Step on the gas and listen for a clicking sound. If you get a clicking sound, look for a reading of less than 0.4 ohms. If the reading is higher, the solenoid is not working and needs to be replaced. On an electric golf cart, if the solenoid is silent – no clicking – use the setting voltmeter to DC volts using the 200 range.
- The solenoid needs to be replaced IF the voltmeter shows a full battery voltage without a click.
- If your voltmeter stays at 0, the problem stems from somewhere else in your cart.
How to check your golf cart for a bad solenoid?
What Are The Symptoms Of A Bad Solenoid In A Golf Cart?
- The first and most obvious symptom is the golf cart won’t start. ...
- The engine on the gas-powered cart starts, but the starter doesn’t disengage after starting. ...
- The solenoid clicks and works sometimes, and sometimes it doesn’t. ...
- The golf cart solenoid doesn’t click when the accelerator is pressed. ...
- The golf cart solenoid clicks, but nothing happens. ...
How to test pulser coil on EZGO?
Steps to replace pulser coil:
- The pulser coil can be removed while the engine is still placed in the cart.
- To remove the coil, the flywheel needs to be detached.
- Use a balance styled puller and attach the same to the threaded holes.
- Now add some pressure and let the puller do its job by removing the flywheel.
How to test motor on EZGO electric golf cart?
- Flip the maintenance switch.
- Reset the battery cable.
- Check your connections.
- Test the solenoid.
- Check your controller's power output.
How to wire a radio to EZGO golf cart?
How To Wire A Radio To EZGO Golf Cart. Simply hooking the radio power to two batteries on your EZGO Golf Cart is not the best way to go. Your EZ-GO cart will need a converter from 48 or 36-volt to 12-volt for the radio. That way it draws power off of all the batteries equally or eventually your golf cart will not run correctly since one or two ...
How do I know if my ezgo golf cart solenoid is bad?
First, turn on the ignition while looking for a reading on the smaller terminals. If nothing is appearing, then press on the accelerator. If the needle doesn't move, then the problem is not with the solenoid. If it jumps and displays full voltage, then the solenoid is the problem and should be replaced with a new one.
How do you test a gas solenoid on a golf cart?
Turn on the engine of the cart and press the pedal downwards. If you hear a clicking sound, then it means that the low side voltage is working. But, if there is no such sound, it means that either there is no low side voltage or there is a problem with the solenoid. Use a voltmeter and engage the solenoid.
What are the signs of a bad solenoid?
As a result, the common signs of a bad starter solenoid include:Engine Doesn't Crank or Start. ... No Clicking Noise When Trying to Start the Engine. ... Starter Spins Without Fully Engaging the Flywheel (Rare) ... Engine Cranks Slowly (Rare) ... Test the battery. ... Check That Power is Getting to the Starter Solenoid.More items...•
How do you check if a solenoid is working?
0:532:52The right way for testing any solenoid coil !! How to test ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipStep one set your multimeter on ohms if the multimeter is not automatic set it on 2k ohms. Step 2MoreStep one set your multimeter on ohms if the multimeter is not automatic set it on 2k ohms. Step 2 place the probes of multimeter across the pins of a solenoid coil.
How do you bypass a solenoid on a golf cart?
Bypassing Golf Cart Solenoid Method If you do decide to bypass the solenoid, this is what you need to do: Take the two larger wires that connect to the solenoid and connect them directly (keeping all safety precautions in place). This should do the trick and if it does not work then the solenoid is not the problem.
How do you fix a gas golf cart that won't start?
First, try this: turn the key switch on, hit the accelerator, and check for a clicking noise. If you don't hear clicking, it's time to take a look at your cart's batteries. Make sure the battery is fully charged and the terminals are cleaned and secure. Next, see how the water level in the battery is holding up.
What happens when a solenoid goes bad?
When you have a bad starter solenoid, the starter motor won't work. This means the engine won't start when you turn on the starter switch or press the start button. However, if your vehicle has an automatic transmission, the engine could sometimes not crank because of the neutral safety switch.
Can you bypass a starter solenoid?
5:037:29Solenoid Bypass - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll you have to do to bypass the solenoid. And make the starter turn is basically connect this hardMoreAll you have to do to bypass the solenoid. And make the starter turn is basically connect this hard copper wire to this point on the battery. Then you're not doing anything with the solenoid.
How do you test a solenoid relay?
0:192:25How to Test Starter Relay Solenoids for Motorcycle, ATV, UTV ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo to test one you actually have to activate it you can't really test it passively with a multimeterMoreSo to test one you actually have to activate it you can't really test it passively with a multimeter. So here I have a power supply setup which basically a battery. Set at 13 volts.
How do you check for a bad solenoid valve?
How to Test a Solenoid Coil?Set your multimeter on ohms. If the multimeter is not automatic, set it on 2k ohms. ... Place the probes of multimeter across the pins of a solenoid coil. If you find 3 pins there, one of them is a flat pin which is connected to the ground. ... Read the number on the multimeter.
How many ohms should a solenoid have?
For irrigation applications, a solenoid is considered to be good if its resistance is between 20 - 60 ohms. It is best to compare resistance measurements to that of a new solenoid. Example, if a solenoid measures 44 ohms, it would be considered good because it is between 20 - 60 ohms.
Should a solenoid have continuity?
While the solenoid coil would be defective if it were electrically open (NO continuity), just having continuity doesn't necessarily mean the component is good. The solenoid's armature could be seized in place and unable to move at all or whatever that armature is connected to could be faulty as well.
How to tell if golf cart solenoid is bad?
One of the most common and obvious signs of the bad solenoid is the golf cart's failure to start when you initiate the ignition process. Once you click the accelerator and turn on the ignition switch, it is supposed to send a signal to activate the solenoid and start the cart. If the cart does not start, there is a big possibility ...
What is a solenoid in golf carts?
Simply put, a solenoid is a device that can transform electrical energy into mechanical energy. It's a coil of wire which is used as an electromagnet. The solenoid has the capability of creating a magnetic field with the help of an electric current. Solenoids work as the “go switch”, which is a must for any golf cart.
Why is my golf cart not starting?
If the cart does not start, there is a big possibility of a damaged solenoid. Another reason for a bad solenoid is that the contacts are starting to get damaged due to overheating or high current passing through them. Note: You may not necessarily experience all of these issues to recognize bad solenoids on your golf cart.
Why won't my golf cart turn over?
For a gas golf cart, the most common symptom is the starter failing to engage, so the engine doesn't turn over. Starters have the responsibility of activating the flywheel. When the flywheel starts to work, the starter is supposed to disconnect.
How to test golf cart solenoid?
A diode allows current to run in one direction, but not in the other. Testing the diode is a simple procedure. Remove the diode from the circuit and check the leads with a continuity tester.
How to tell if solenoid is bad on golf cart?
The common symptom of a bad solenoid is no clicks when the cart’s ignition is on and you press the accelerator.
Why doesn't my golf cart solenoid click?
This can be a faulty wire connection, but can also mean the solenoid is beginning to fail. The golf cart solenoid doesn’t click when the accelerator is pressed. This again can be faulty wiring or a failed solenoid.
What to do if your solenoid is not zero?
If the reading is not zero, then the solenoid is stuck and needs to be replaced. If the ohmmeter does read zero, set the cart to forward travel and turn the key switch on. Press the accelerator pedal (or have a friend do it) and you should hear a click. If you don’t hear a click, measure the resistance anyway.
How to check if a battery is low?
First, follow these steps: Step 1 – Check the battery voltage from the positive connection to the battery negative. A solenoid uses 12-18volts and low voltage will not activate the solenoid. Step 2 – If the voltage is low, check the cable ends for corrosion. Clean and charge the battery.
How to tell if a golf cart won't start?
The first and most obvious symptom is the golf cart won’t start. If it is a gas-powered cart, the engine doesn’t turn over, and if it is an electric cart, the cart doesn’t move. Now, on to the next symptoms…. The engine on the gas-powered cart starts, but the starter doesn’t disengage after starting.
Where are the solenoids on a golf cart?
In all golf carts, new and old, the solenoids can be found under the seat or in the engine well and are easily identifiable by the wires that lead to them. Banks of heavy duty solenoids, as in the previous illustration, are mounted on the side or back panel near the electric motor.
How to check a solenoid?
Follow These Simple Steps to Check the Solenoid: 1. You will need a couple of tools: a voltmeter or multimeter, and (typically) a ½” wrench. 2. Disconnect any cables from the two large terminals. Be sure to wrap the cable ends in tape, and keep the ends separate from each other. 3.
What voltage is applied to the two small terminals to activate the solenoid?
Battery voltage is applied to the two small terminals to activate the solenoid, which then connects the two large terminals together. From time to time, the two large terminals malfunction and the solenoid needs to be replaced.
What does it mean when a golf cart solenoid goes bad?
Technically, in fact, a solenoid is a shape – a shape in which the length of something coiled is longer than the diameter of the coils. In engine starters, this refers to the smaller motor ...
How to check if a golf cart solenoid is silent?
On an electric golf cart, if the solenoid is silent – no clicking – use the setting voltmeter to DC volts using the 200 range. First, turn on the ignition while looking for a reading on the smaller terminals. If nothing is appearing, then press on the accelerator. If the needle doesn’t move, then the problem is not with the solenoid.
Why is my golf cart not clicking?
On an electric golf cart, the most common symptom is the solenoid is not delivering electricity to the controller when the vehicle’s ignition is turned on. In normal operating conditions, the solenoid clicks on and off with the ignition switch. A failing solenoid will generally not click. Two things could be going on here.
What does a solenoid do when you turn the ignition?
Step by step, it looks like this: When you turn the ignition key, a small amount of electricity goes to the solenoid. The solenoid uses that small amount of juice to close two heavy-duty contacts that allows a large jolt of electricity to pass through the starter. The solenoid also sends a pinion gear forward, which is the device ...
Why do golf carts have solenoid?
The solenoid is simply there to allow electricity to flow freely to the controller and motor which will result in a running golf cart. RELATED: 4 Signs you need to Replace your Golf Cart Batteries.
Why won't my solenoid click?
The solenoid might not be getting enough electricity to do its work – which could be caused by loose connections, a weak battery or the coil wearing out.
Why do you use electrical tape on a solenoid?
When you do this, use electrical tape to seal the cable ends, so they won’t form a circuit by accidentally touching each other or connecting through a metal conductor inadvertently. Doing this will ensure the vehicle will not run while testing the solenoid.
What is a solenoid in a golf cart?
A golf cart solenoid is one of the major components of any golf cart. This part is essential regardless whether you own an electric or gas golf cart because both types primarily rely on a solenoid for their movement. What this means is whichever brand or model you choose for your cart, a solenoid is truly an indispensable part of the vehicle.
How to get a golf cart going without a glitch?
To get your golf cart going without a glitch, you most definitely need the solenoid of your cart to be functioning properly. Thus, it goes without saying that you must check this component occasionally to monitor its performance so that you don’t get stranded mid-way.
What is a solenoid wiring diagram?
A solenoid wiring diagram can be very helpful in guiding you about the various connections made to and from the solenoid. This can come in handy when you set out to troubleshoot a problem in your cart on your own. The solenoid wiring diagram is generally very simple, straightforward and self-explanatory.
What does the inductive throttle sensor do on a golf cart?
When you push down the pedal of the golf cart downwards, the inductive throttle sensor sends out the first low power signal to activate the solenoid on its low side and the speed controller. The low side is the steel rod of the solenoid.
How often do solenoids work?
Since solenoids need to work very frequently; turning on and off each time you use the cart, they are prone to wear and tear easily. This is not surprising as they can switch on and off as much as 1,500 times a day). One of the first indications that a solenoid is faulty is when your cart fails to start.
Why is my golf cart not clicking?
This may be because the safety reed switch is not working properly in the charger socket. There could be a loose connection of the MOLEX plug.
Why does my gas cart not turn over?
In a gas cart, a bad solenoid prevents the starter from being engaged and therefore results in the engine not turning over.
What is solenoid in golf cart?
Basically, a solenoid is an electromagnetic coil that converts electricity into a form of mechanical energy. It has many applications, one of which of course is being a switch that connects the battery of your golf cart to the starter or motor, with the help of both the high and low power circuits. This device is present in ...
Why do golf cart solenoids need maintenance?
Just like many things, a golf cart solenoid needs proper maintenance in order to avoid any hassle that can disrupt its functions and minimize breakdowns which can put a damper on your enjoyment .
Why does my golf cart make a clicking sound?
The Golf Cart Has a Clicking Sound. As mentioned earlier, low amperage and insufficient voltage will cause a clicking sound. But when the solenoid is already damaged in the first place, it will also give off those clicks when you try to start your cart.
Why does my golf cart solenoid turn inactive?
That’s because the voltage is passed through it via its subparts, which are the steel plunger and a thin wire, allowing the flow of energy from the battery to the motor to create a linear motion . During its operation, your solenoid turns somewhat inactive, which reduces the usage of your golf cart battery.
What to do if your solenoid is not clicking?
In case there is no click at all, adjust your measuring device to 200 volts and check the small terminals this time. If they give off a zero reading, you have a problem other than your solenoid. If a full voltage registers without any clicking sound, your coil is toast, therefore, your solenoid calls for a replacement.
How many wires does a golf cart have?
It has a total of four-wire connections or terminals, big and small at two posts each. The solenoid may well be one of the most crucial and utilized components of a golf cart since it has to perform frequently as the number of times you power it on. It will work on the principle of attracting and repelling material that is sensitive ...
What happens if a starter is held on?
When the starter continues to hold on, it will not only damage the flywheel, but the adjacent components as well such as the circuit and solenoid altogether. For gas-powered carts, the bigger terminals alongside the starter remain in operation even when the microswitch is not powered on.