The fuse box is located behind the storage compartment on the driver’s side of the dashboard (LHD). Open the storage compartment, squeeze from the sides, and pull it towards you to access the fuses. On right-hand drive cars, this fuse box is most likely located behind the cover on the left side of the glove box.
- Remove Cover - Locate interior fuse box and remove cover.
- Locate Bad Fuse - Find the fuse that is tied to the bad component.
- Remove Fuse - Take out the fuse in question and assess if blown.
- Test Component - Secure the cover and test component.
How do you check a fuse to see if it's blown?
Test the fuse. If you're using a digital multimeter set to measure resistance, touch the probes together to get an initial reading. Then put the probes on either side of the fuse and check if the reading is similar. If it is, then the fuse works properly. If you get no reading or "OL", then the fuse has blown.
How do I find a blown fuse in my car?
The blown fuse will be apparent because the wire element within will have melted or burned from the higher electrical current. You can also use a test light or a multimeter to identify the dead fuse without having to pull it out. Both tools are affordable and easy to use.
What are 3 ways to check fuses?
Use a multimeter to test cylindrical fuses in electronic devices.Touch one of the multimeter's probes to each of the fuse's terminals. As with plug fuses, a resistance reading of 0 to 5 Ω means the fuse works. ... You can inspect cylindrical fuses for broken filaments or charred marks just like automotive and plug fuses.
How do you troubleshoot a blown fuse?
6:457:57How to troubleshoot a blown fuse in motor control. - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhether this fuse is good or fuse is blown we're gonna read zero volts. So what we need to do is useMoreWhether this fuse is good or fuse is blown we're gonna read zero volts. So what we need to do is use the crisscross method. We're gonna keep this lead on and we're gonna measure voltage.
Should I disconnect battery before checking fuses?
Before you start working on any automotive project, it's important that you turn off the engine and disconnect the battery, especially before doing any electrical work. Any misstep with automotive wiring while the battery is hooked up could cause further damage and potentially give you an unpleasant zap.
How do you check a car fuse without a multimeter?
Put one wire to neutral/common, and one wire on the line side of the fuse. If voltage is present the bulb will light up. Now move the wire from the line side to the load side of the fuse. If the fuse is good the light will come on.
Can you use a multimeter to test fuses?
To test if the fuse is blown, we require a multimeter. Once configured, a multimeter can measure the resistance of the fuse element. Resistance is measured in Ohms 'Ω'.
How do you check a car fuse with a multimeter?
1:014:10How to check car fuses without pulling them out - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you can test that without having to remove it great little tip so on your multimeter you want toMoreSo you can test that without having to remove it great little tip so on your multimeter you want to set it to the ohm setting on the lowest setting mine goes down to 20 ohms.
What causes blown fuses in cars?
A short in the electrical system will just cause a fuse to blow, rather than the wiring overheating or melting. A short is just a poor connection between two conductors that supply electricity, causing an electrical overload in the circuit.
How do you check fuses?
0:572:58How to Check For Bad Fuses With A Multimeter - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow we'll just touch both sides of the fuse. And check the meter and then you want it close to zero.MoreNow we'll just touch both sides of the fuse. And check the meter and then you want it close to zero. Now a fuse you're not gonna have any in between it's either gonna be good or it's bad unless.
What happens if a fuse blows?
A blown fuse can trigger a circuit breaker, which will knock out the power to a section of your home. Getting to the bottom of the problem will help you get the power back on as soon as possible.