Golf-FAQ.com

golf cart forward switch only works when its too tight to shift

by Greg Towne Published 3 years ago Updated 2 years ago
image

Your golf cart may be stuck in either forward, reverse, or in neutral and will start and rev the motor, but it will either not go anywhere, or only go in forward or reverse. How to Fix it Remove the seat and move the shift lever. If the lever isn’t broken, look at your cable where it switches gears in the transmission.

Full Answer

Do golf carts shift forward and reverse?

The important point to note here is that the shifting forward and reverse in these golf carts do create trouble sometimes, particularly on slopes. There’s a certain level of tightness about them and you would want to tighten the cable accordingly.

Is your f/R switch affecting your golf cart?

If you are a golf enthusiast and own a cart, then you are likely going to experience wear and tear issues that can affect your F/R switch. When the switch is in the reverse mode you get only a buzzer sound. The cart moves forward even when the switch is in the neutral position. Not getting the best speed while in the forward position.

Why does my golf cart buzz when in reverse?

If you are a golf enthusiast and own a cart, then you are likely going to experience wear and tear issues that can affect your F/R switch. When the switch is in the reverse mode you get only a buzzer sound. The cart moves forward even when the switch is in the neutral position.

How do I know if my golf cart switch is bad?

When the switch is in the reverse mode you get only a buzzer sound. The cart moves forward even when the switch is in the neutral position. Not getting the best speed while in the forward position. Sometimes you may even notice a burning smell that can be due to overheating.

image

Why is my golf cart not going forward?

The problem could be with either the Run/Tow switch or Forward/Reverse switch or both. Check the switches to ensure that they aren't stuck midway. If they are, getting them released should help. However, if they show signs of wear and tear, you must get them replaced.

Why would a golf cart go in reverse but not forward?

A faulty Forward/Reverse switch can cause a Club Car golf cart to move in reverse but not forward. Replace the entire switch and the contacts if they are burnt. The cart moving only in the reverse and not in the forward position is peculiar and there are only a few areas that need to be checked.

How does a forward reverse switch work on golf cart?

0:379:43Golf Cart Forward and Reverse Switch Direction Selector Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipThat is brand new it simply cables connect to the bright copper colored contacts. And the switchMoreThat is brand new it simply cables connect to the bright copper colored contacts. And the switch rotates through a hand action and that changes the polarity.

Why won't my EZGO golf cart go forward or reverse?

Electrical Issues For example, if your run/tow switch has malfunctioned, your cart won't go forward or backward. This switch is designed to change your cart's operating mode from normal operation to increased power for towing. Check the switch to make sure that it isn't “stuck” between the two modes.

How do I know if my golf cart solenoid is bad?

Press on the accelerator while the key is turned on and the cart is in forward.The solenoid needs to be replaced IF the voltmeter shows a full battery voltage without a click.If your voltmeter stays at 0, the problem stems from somewhere else in your cart.

How do I troubleshoot my EZGO forward/reverse switch?

Check all the connections and make sure each part is getting power by using the multimeter. Have your foot firmly on the brake, put in the key, and the F/R switch in the forward position. When you push the go pedal if the solenoid charges up then your EZGO F/R switch is good to go.

How do you test a forward forward switch on a golf cart?

Place your foot on the car's brake, insert the key, and put the forward-reverse key in the forward position. If you see that the solenoid charges up pushing the pedal, then your forward reverse switch is working fine. As you put your Golf Cart in the forward mode, check your multimeter for full voltage.

How do you test a golf cart switch?

Testing a Club Car Ignition SwitchFind the back and red wires on the back of your battery pack.Connect the black wire to the negative terminal and the red to the positive.Keep the cart turned off while you work on it.Check the wires with a probe meter while the cart is off – only one wire should have a charge.More items...

Why does my electric golf cart only go in reverse?

One possible cause of a cart not moving forward or in reverse is because of the way the wires are hooked in reverse. To fix this, you should switch the position of both the wires that are leading to the motor. If the golf cart is not rolling across freely, there might be an issue with the brakes.

Do all electric golf cart motors have a reset button?

Electric golf cart motors have a reset button on their chassis which is designed to put your motor back into its original factory state. While it doesn't repair damage that may have occurred to the motor over the years, obviously, it does help to overturn any changes to the operation which may have occurred.

How do you make a golf cart go forward?

0:5911:38Golf Cart Forward Reverse Switch - YouTubeYouTubeStart of suggested clipEnd of suggested clipMost likely that your forward reverse switch. Which is located right there. This is what makes yourMoreMost likely that your forward reverse switch. Which is located right there. This is what makes your golf cart go forward or reverse.

How do you test a EZGO pedal switch?

There are multiple switches on an EZGO golf cart and the following step-wise guide can help you test all of them. What is this?...How to Test EZGO Micro SwitchStep 1 – Access the Micro Switch. ... Step 2 – Connect a Voltmeter. ... Step 3 – Check for Continuity. ... Step 4 – Reset the Switch.

What makes a golf cart go in reverse?

The simplest and most likely cause of reverse problems in a golf cart is a malfunctioning F&R switch. This switch – which stands for forward and reverse – is common on most golf carts and makes it easier for you to go forward and in reverse without requiring a lot of complex machinery or levers.

Where is the solenoid on a ezgo golf cart?

0:498:12How to Replace Golf Cart Solenoid Coil | Install - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is not from one of the resistor set okay we've got this we've got the car let's get startedMoreThis is not from one of the resistor set okay we've got this we've got the car let's get started cylinder is located under this black box here on the passenger side of the car.

Where is the controller on ezgo golf cart?

All EZ-GO speed controllers are equipped with a maintenance switch that needs to be flipped before you begin work on repairing the problem. You will likely find the switch under the seat of your golf car,t but if you're having trouble finding it, consult your owner's manual.

Does a gas golf cart have a transmission?

All golf carts (much like cars) have a clutch, which is the part of the drivetrain that helps the put the power of the motor down through to the wheels/ground. Golf cart clutches are a part of the Continuously Variable Transmission (or CVT).

How far is the shift cable on a golf cart?

A golf cart shift cable adjustment is 1 3/8-inch from the washer and is to be made till the end of the threads. The adjuster has to be in the neutral position while making this change in the cable’s position.

How to adjust a golf cart?

If you are only making an adjustment to the shift cable, follow these steps: 1 Examine the shift cable closely for any damage. 2 If it is damaged you must go for a full replacement. 3 Do this inspection when the golf cart’s engine is off. 4 Allow the engine to cool before you do this exercise. 5 The adjustment has to be done at both ends. 6 One is the transaxle end and the other end is where you use the handle to shift R and F. 7 You should thoroughly clean the cable using a spray like WD40. 8 You can do the shift cable adjustment, with the shift lever in the forward position and then again changing it to the reverse position. This has been seen to be the better method in the Yamaha G2

How to adjust shift cable on Yamaha G20?

You can adjust the shift cable in the Yamaha G20 Gas by removing the adjustment nuts by slackening the jam nuts. Get the cables out by moving the shift lever back and forth. Now replace the cable and keep adjusting the cable-ending position at the transaxle end. They have to be of equal length.

Why is my Yamaha G9 not moving?

If you are facing the issue of the shift not working forward or reverse, it could be because a detent ball bearing may have fallen off during some other work on the transmission.

Why is my shift not moving?

The belt has been seen as one possible reason for the shift not moving freely. You can also check if the belt is of the right length. Some people removed the belt and say the shift worked fine afterward. Belts with shorter lengths can be fitted to see if it solves the issue.

Why do you need to mark the location of the bracket on the vehicle before pulling it out?

This helps to ensure that the replacement does not alter the arrangement in the area.

Can you replace the shift cable on a Yamaha G2?

You have to access the transaxle on the rear of the cart and pull out the bracket where the cables are attached. You can now replace the cable. Remember to mark the location of the bracket on the vehicle before pulling it out.

Where is the F/R switch on a golf cart?

The F/R switch on a EZGP PDS is located under the seat of the golf cart. Here are some pointers: If you want to convert it to a rocker type switch on your dash, ensure to use diodes that are at least 3 amps. Check the low voltage setting, it should be less than your cart voltage.

How to Install EZGO Forward Reverse Switch?

Installing the EZGO F/R switch is an easy process that I have explained below. But please be very careful while handling the battery and other electronic equipment.

Why does my Ezgo golf cart get hot?

A F/R switch on a EZGO golf cart is likely to get hot due to of loose or broken contacts. These broken contacts increase the resistance and heat build-up causing the FNR switch to heat up.

How to test EZGO FR switch?

The easiest way to test your EZGO FR switch is to check and confirm if the solenoid starts working when you start the golf cart. If this works, this means your cart is in working order.

What to replace FNR switch with?

If nothing else works replace the manual FNR switch with a set of solenoids.

What to do if top cover doesn't fit?

In case your top cover does not fit correctly, bend the wires to fit them in. Pro Tip: Ensure your nuts and screws are as tight as possible. If not, they are likely to vibrate when moving and this could lead to overheating and damage to your F/R switch and/or the cart as well.

Why does my cart keep melting?

The melting could be due to excessive heat. Sometimes this can cause the contacts to sink in as well. Delaying a fix could prove harmful to your cart, so act fast.

Which arms are difficult to move?

The forward and reverse motion arms are difficult to move.

Does a 1995 Club Car go in reverse?

1995 Club Car - Engine Runs fine and will go in reverse but

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9