
Apply 2 (extra) WRAPS of grip tape (which will add ~1/32" to the diameter) IMPORTANT NOTE: You only need to apply solvent to the last layer of tape, before installing the grip. * (Another) IMPORTANT NOTE: Sometimes adding more than 1 layer of grip tape may compromise the torque (the amount of twisting that can occur during a swing) of your club.
Full Answer
How do you tape the end of a golf club shaft?
Wrap the tape around the shaft. Then take the extra tape hanging off the end, twist it and tuck it into the shaft butt. Tucking in the tape provides 3 things. First, it allows for proper sealing and adhesion at the butt end of the grip.
How do you keep the grip from sliding off the shaft?
The grip could slide off the shaft resulting in serious injury or harm. Wrap the tape around the shaft. Then take the extra tape hanging off the end, twist it and tuck it into the shaft butt.
How many tape wraps do I need to make my Grip bigger?
Using one layer of tape around the shaft already increases your diameter by 0.0075 x 2, or 0.015 inches. Based on this calculation, here are the number of wraps to use when you want to increase the size of your grip, starting with a bare grip:
What happens if I remove the grip and tape from the shaft?
It can cause unwanted bulges in your grip. Most importantly, you'll end up with extra layers of tape, increasing the diameter of the grip which may not be what you want. After the grip and tape are fully removed from the shaft, we can now prep the new tape. If you are working with a roll of tape, pull out and cut the length of tape you will need.

How many layers of tape do you put on a golf grip?
Standard grips with 3 layers of tape.
Do you need double sided tape to Regrip golf clubs?
Yes, you can regrip your golf clubs without a tape by using an air compressor. The advantage of using an air compressor is the ease of use. This method is also less time consuming when compared to the solvent or tape method.
Is golf grip tape just double sided masking tape?
What tape is used for golf grips? This is a loaded question with a few views, let's start with the simple answer… Double Sided Tape is the golf grip tape of choice.
Can you leave the old tape on when regripping golf clubs?
Make a Tape Decision One option is to leave the existing tape on your clubs and reuse it. This is possible, but it's probably the least desirable of the three options. After all, it's likely the tape won't form as strong a bond with the grip as it did the first time around.
How many wraps of tape do I need for a midsize grip?
A standard grip with 3 wraps of tape is as close to midsize as you get.
How long should clubs sit after Regripping?
It's tempting to take your clubs out for play once the grips on are. However we strongly recommend waiting at least 6 hrs after re-gripping. The solvent needs to completely cure and you'll want to leave the clubs in a dry and cool area during this time.
How can I Regrip my golf clubs without a solvent?
What kind of solvent do you use to grip the golf clubs?Water. You can use water as long as you are using water-soluble tape. ... Paint Thinner and Mineral Spirits. Paint thinner or mineral spirits are much more cost friendly solutions than traditional grip solvent that you would purchase at a golf store. ... WD-40. ... Hairspray.
How do I make my golf club grips tacky again?
0:121:12How to Make Golf Grips Tacky - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne is to clean the grip you can clean the grip using just soap and water but be sure to dry it offMoreOne is to clean the grip you can clean the grip using just soap and water but be sure to dry it off or scrape. The grip now you can do this using a pocketknife or a piece of sandpaper.
What do I need to Regrip my clubs?
0:205:48How To Regrip A Golf Club | Golf Pride - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd worn out and that's the reason you need to take it off so the way that I remove a golf grip isMoreAnd worn out and that's the reason you need to take it off so the way that I remove a golf grip is simple. I get the hook blade. And I always cut away from myself with the blade.
How do you remove old golf club tape?
Using a tape stripper, peel the tape off the shaft by pushing the tape stripper through the length of the tape. Rotate the shaft after each strip is taken off until all tape is removed. On a graphite shaft, after warming the tape, it is recommended to peel the tape off by hand. Tape strippers can damage graphite.
Can you use WD40 to Regrip golf club?
Some people will use WD40 when they are regripping golf clubs. WD-40 is not the best solution to use as a grip solvent because it is priced a bit higher than other choices, but it will work. You can use the WD-40 to remove grip tape from golf clubs, and then you can use it as the solvent when you put a new grip on.
Can I reuse golf club grips?
Golf grips can be removed and reused if they are in relatively good condition and if you are able to remove neatly without destroying them. If you are removing an old, damaged, or worn-out golf grip, cutting it off is the easiest option.
Step 1
Measure the length of the grip you plan to install. Mark the measurement on the shaft of the club with a marker.
Step 3
Apply the tape lengthwise to the shaft so the is half-inch of excess tape extends from the butt of the shaft. Begin to smooth the tape over and around the shaft, but do not wrap in all the way around the shaft.
Step 4
Peel off the protective top layer of the tape. Finish wrapping the tape around the shaft. Twist the excess tape at the top and push it into the shaft to seal the end.
What thickness is 1/64 golf tape?
Now it seems that they went to a diffrent manufacturer and the tape though still advertisedf as 1/64" is actually closer to 0.006" in thickness. Therefore, you're not going to get 1/64" using that tape and need to figure that out in your calculation. quote]
Can you use double sided tape for wraps?
Many use single sided as build up largely because it's less expensive and easier to use but many will just use double sided for all wraps. Using double sided for build up would be like using single sided 0.015" build up tape (instead of 0.010" build up tape).
What is a grip build up?
Adding extra layers of grip tape to the shaft while installing a grip will increase the diameter which the grip will go over. Whether it’s one, two, or more extra layers of tape on the shaft when the grip is installed, the rubber grip will stretch over the tape, thus making the grip larger.
Reasons for building up your grip
Whether it’s a feel preference or for shot performance, here are a few reasons why golfers add this specific item to their installation spec sheet.
How do I build up the grip with tape?
If you are taking your clubs to your trusted golf shop or course to change the grips, tell them how many extra wraps of tape you would like and they will know what to do.
How much tape do you need to install a grip?
To install a grip, you need at least 1 wrap of grip tape to match the stated size of the grip. This means there is one layer of tape that goes around (and does not overlap) the grip, regardless of the size of the grip.
Why do you need solvent for club grips?
Solvent is needed to both lubricate as well as activate (the stickiness of) the tape so that when dry, the tape will adhere to the inside of the grip. We recommend using a generous amount of solvent to avoid the grip getting stuck halfway. Many club-builders allow the solvent to drip into a pan so they can re-use it again.
How to use double sided tape?
When using double-sided grip tape, make sure to first peel the backing off of the tape. BOTH sides of the tape are sticky. If you leave the wax paper on one side, the tape may not adhere properly to the grip.
Can you use tape solvent in grip kits?
Yes, you can! We sell tape solvent (made by Brampton Technologies) in all our grip kits. But you should know that this solvent is actually NOT the most effective liquid for re-gripping. We use it and sell it here because it is the only one safe enough to meet all California environmental regulations (where our company is based).
How to remove old grips on golf clubs?
Removing the old grip may require the use of a hook blade or knife. Remember to always cut AWAY from you, to avoid injury. Once you've sliced through the grip, you should be able to pull the old grip off fairly easily. Working with golf clubs, it helps tremendously to use a vice and shaft clamp to head the club steady.
How long after re-gripping golf clubs can you take them out?
It's tempting to take your clubs out for play once the grips on are. However we strongly recommend waiting at least 6 hrs after re-gripping. The solvent needs to completely cure and you'll want to leave the clubs in a dry and cool area during this time.
Why do you tuck in tape?
First, it allows for proper sealing and adhesion at the butt end of the grip. Second this prevents solvent from entering the shaft. Third (and most importantly), it prevents the grip from getting cut/damaged from the sharp edge while sliding onto the shaft (during step 7).
What is grip solvent?
A few things to understand about grip solvent: First, solvent is needed as a lubricant that allows you to slide the grip onto the shaft. If there isn't enough solvent applied inside of the grip AND on the shaft, then there is a high likelihood that the grip will get stuck midway. Second, solvent acts as a tape activator.
How to work with roll of tape?
If you are working with a roll of tape, pull out and cut the length of tape you will need. In most cases, you can have the length of tape be equal to the length of the grip. If you are using pre-cut tape strips, then you are ready to move onto step 3. Fyi - if the tape strip is up to 1" shorter than the grip itself, that is OK.
Do you need to remove wax paper from tape?
Both sides of the tape are meant to be sticky. So you'll need to remove the wax paper backing from the tape. If you're working with pre-cut tape strips, there is wax paper on BOTH sides, so remember to remove them both!! Common mistake alert: This seems like an obvious step.
Do you need a vice for golf clubs?
Working with golf clubs, it helps tremendously to use a vice and shaft clamp to head the club steady. While this is not necessary, a vice can help keep your workspace organized and clean. And since the club is held securely by the clamp, this can help prevent injury as well. Vices are sold at most local hardware stores.
