- Determine how much of the shaft’s tip you wish to trim. ...
- Place the shaft into a rubber golf club clamp, then insert the clamp into a vise. The rubber protects the graphite from damage.
- Wrap two or three layers of masking or electrical tape around the area to be cut. The tape helps prevent the shaft from splintering.
- Measure the distance that you wish to trim from the tip, then mark the distance on the tape with a pen.
- Cut carefully along the marked line with a hacksaw, insuring your blade is perpendicular to the shaft.
- Determine how much length must be trimmed from the butt end of the club. This typically depends on the type of club you're constructing.
- Tape and mark the area to be cut, as you did with the tip. However, add 1/8 inch to the cut to account for the grip cap.
- Cut the butt end the same way as you trimmed the tip. ...
How to cut a fiberglass golf shaft?
To do that, the DIY golfer will have to:
- Remove the existing grip.
- With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw.
- Re-install a grip on the newly shortened shaft.
- And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club. ...
How do you cut down a golf shaft?
- Measure the amount that you want to cut.
- Measure from the top of the shaft down.
- Measure carefully and make clear thin marks.
- Take note of whether your cut should take the marks or leave the marks.
Can you change a shaft from graphite to steel?
The steel shafts are replaceable and graphite can be replaced with, meaning there is no heavier weight to the clubs. However, the grip may need to be changed, and you will probably have to use a new heat treatment. It requires a bit of effort, but it can be done.
How to replace the grip on a graphite golf shaft?
How to Replace a Graphite Shaft on a Golf Club
- Remove your old graphite shaft. There are two ways to do this step. ...
- Prepare you new shaft. A graphite shaft has a protective coating, so you must remove it from the tip of the shaft by carefully peeling it off with ...
- Put on you new graphite shaft. ...
- Cut the shaft and add your new grip. ...
How do you shorten a graphite driver shaft?
With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw. Re-install a grip on the newly shortened shaft.
How do you cut graphite?
Most people like to use a hack saw with a blade that can cut graphite. Many golf club part manufacturers will sell blades like this, and they are usually easy to install on your current hack saw. A typical hack saw blade is probably not going to do the trick. Many people also use a Dremel-type tool.
What do you use to cut a golf shaft?
0:394:01How to Cut Golf Shaft DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou need a pipe cutter.MoreYou need a pipe cutter.
How much can you cut off a golf shaft?
If you are going to shorten a golf club, there are a few things to keep in mind. The more shaft you cut off, the lighter, more stiff, and effectively flatter the club becomes. For every 1/2 inch you remove, you will lose approximately three swingweight points.
What do you cut graphite with?
0:092:12HOW NOT TO CUT GRAPHITE GOLF SHAFTS / Wrong Tool for the JobYouTubeStart of suggested clipEnd of suggested clipAnd the answer is emphatically no and i'm going to show you real quick what happens if you do chooseMoreAnd the answer is emphatically no and i'm going to show you real quick what happens if you do choose to try and use the pipe cutter on a graphite shaft remember graphite shafts you're going to want to
Can you cut a graphite shaft with a chop saw?
0:031:17How To Cut a Golf Shaft with a Chop Saw - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou want to use an abrasive wheel. And you'll notice that the cutting edge is devoid of any teeth.MoreYou want to use an abrasive wheel. And you'll notice that the cutting edge is devoid of any teeth. This ensures that you'll stay for you cut both steel and graphite shafts.
How do you shorten a golf club shaft?
0:483:03Golf Tips : How to Trim Golf Club Shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst thing we got to do is determine the length of the golf club we're going to we're going to cutMoreFirst thing we got to do is determine the length of the golf club we're going to we're going to cut and how much we need to cut off of it. So we're going to lay the club.
Does cutting shaft make stiffer?
When you cut off a portion of the softest part of a golf shaft (the tip), it increases the overall stiffness. The handle section of a shaft, on the other hand, is longer and more uniformly stiff, so removing material from the handle does not make such a pronounced difference in overall stiffness.
Can I cut down my driver shaft?
Shortening the shaft will make the club shorter but it will also make the shaft stiffer and adjust the swing weight as well. Plus, the more length you remove, the less flex your club will have. Depending on how much you cut it down, it could move a regular flex to a stiff or a stiff to an extra stiff.
Can you shorten your own golf clubs?
If you have purchased a set of used golf clubs that are too long, you can quickly cut them down to size with a hand-held rotary tool. You can also resize your old clubs and pass them on to your children. The shaft of a golf club is narrower at the head end to generate power on the swing.
Is it bad to shorten golf clubs?
For most golfers, having clubs that are too short will be better than if they're too long, but can still result in inconsistent shots. Clubs that are too short will make you stand bent over, which can cause back pain. You'll also have the tendency to push the ball a lot.
How much does it cost to shorten a driver shaft?
Generally, this fee will be about $15 to $35 depending on where and when you get the work done. Replacing a shaft on a driver is a bit more work than regripping a club.
Can you cut graphite?
A safe way to cut graphite shafts by hand Yes, it is even strong enough to cut steel. It can cut through a graphite shaft in 15-20 seconds after the shaft has been securely place in your vise. The model we sell fits on a standard 12” hacksaw frame found at any hardware store or in many home shops.
How do you cut a graphite rod?
1:473:26Rod Building 101: How to Cut Your Rod Blanks - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd by using the tape you can prevent the rock from splintering. Itself. So it's okay this is just aMoreAnd by using the tape you can prevent the rock from splintering. Itself. So it's okay this is just a quick tip on how we used to cut the rod to see it's got that little bevel on it.
Can you machine graphite?
Despite being a softer material, graphite is actually one of the most difficult materials to machine. There are many considerations machinists need to make in terms of tooling, coolant use, and personal safety when it comes to machining these parts.
Remove the Grip
The first things to do is to remove the grip tape from the golf club [how to remove grip tape from golf club]. This will make it easier to cut the shaft. You can use a cutter to slice the grip from the top and slowly peel it off the club. The specific process can differ, which will depend on the material of the grip.
Measure the Shaft
With the grip now off the golf club, the next step is to take the appropriate measurement. Use a measuring tape and run it from the top to the bottom of the shaft. Mark the specific spot where the measurement ends. You can do this with a marker or by wrapping the tape around the tip. The measurements should be as precise as possible.
Cut the Shaft
Now comes the most important part of the task. Before cutting the shaft, make sure that it is in a stable position. Some might think that they can cut by holding the shaft with one hand, but this isn’t the case. For your safety and to make the cut more accurate, we recommend placing the golf club in a vise.
Wrap a Grip Tape
Once you are done cutting, the next step is to wrap it using your grip of choice. Pick a material you are comfortable with. This is important since it is the part that you will be holding, and hence, it will affect how you swing the club. Also, it must absorb vibration, making sure of your highest level of comfort, even during aggressive shots.
Step 1: Prepare tools
Preparing your tools is the first step but will contribute to your success. If you prepare incorrectly or lack the tools, it will take time in the process.
Step 2: Measure and mark
Measuring and marking will help you know exactly where to cut and make them more specific. It is impossible to guarantee that you will be satisfied with the first measurement results.
Step 3: Prepare to cut
After you have determined the point you want to cut, do not rush to pick up the knife to cut it. It would help if you prepared a little more to make the cutting process more convenient and safe for yourself.
Step 4: Cut a graphite golf shaft
After a complicated preparation process, now you have come to the most critical step: cut a graphite golf shaft. However, you do not need to worry too much if you have carefully prepared the above steps.
Step 5: Check the cut
The process of cutting a graphite golf shaft is almost complete. Now you just need to double-check that the cut is exactly what you want, and you can use it.
Why use masking tape on graphite shafts?
Secondly, by wrapping tape around the shaft, reduces the likelihood that the shaft would splinter during the last moment of the cutting process.
What is a rod saw blade?
Even for veteran clubmakers, the rod saw blade is handy to cut a single shaft instead of firing up your motorized equipment or to find that you have a damaged blade in need of replacement. Plus it comes in handy cutting the shaft angle and through bore plugs for those golf club thru bore installations. All-in-all, it is a long-lasting tool no golf ...
Can a hacksaw cut steel?
Yes, it is even strong enough to cut steel. It can cut through a graphite shaft in 15-20 seconds after the shaft has been securely place in your vise. The model we sell fits on a standard 12” hacksaw frame found at any hardware store or in many home shops. How To Tips. I would like to share a few how-to tips as well.
Can a rod saw blade cut steel?
It makes thin straight cuts in all types of shaft materials used in golf. Yes, it is even strong enough to cut steel.
Can you cut graphite shafts?
Graphite shafts need special care to be cut properly. A tubing cutter, that you would use to manually cut a steel golf shaft, will crack or destroy a graphite shaft in no time at all. Don’t think about pulling the hacksaw from your tool chest either.
Feedback
Hey guys. I want to cut a half inch off my driver shaft. I've done a lot of searching but am not finding a definitive answer. I know you need to wrap the area you're cutting in masking tape but what's not clear to me is the correct type of blade to use. Some say hacksaw, others say a chop saw (which I have to admit, I have no idea what that is).
Feedback
i've used a dremel -- or a chop saw. either work fine. hacksaws COULD splinter the ends --not sure if it's 100% true but, i'd rather not risk it.
Feedback
I used a miter box and hacksaw with a blade with the highest number of teeth per inch (TPI) I could find at the hardware store. Came out just fine.
Feedback
What is a chop saw? I have a dremel but what attachment should be used? Also, if using a dremel, how do you get the cut perfectly straight?
Feedback
I'll use anything that has fine sharp teeth. I've done most of my shafts by hand recently because I have limited space and its easier without needing electricity and cords.
Feedback
Dremel cutoff wheel. They use a similar abrasive material circular saw blade as a chop saws uses (which is what you will find at a club maker for cutting graphite shafts). I use it for my graphite shafts as well as my carbon fiber arrows for my compound bow. Never had problems with either.
Feedback
Chop saw is best, Dremel with cutoff wheel will work (but it is tough to make an even cut), and if you use a hacksaw get a 'grit' blade.
Series Navigation
I know this might seem obvious, but be sure to measure and mark off the point at which you are cutting. Especially while tipping a shaft (you can’t undo this), it is important to have precise measurements. Use a sharpie to make your marks on the shaft. Here is a tutorial on how to measure golf clubs.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
How to shorten a golf club shaft?
To do that, the DIY golfer will have to: 1 Remove the existing grip. 2 With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw. 3 Re-install a grip on the newly shortened shaft. 4 And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club. "If clubs are shortened and no weight is added back to the clubhead, the chances of the length reduction having the desired effect are somewhere between slim and none."
What is the difference between a golf shaft and a tip?
All golf shafts taper; that is, their circumference is greater at the grip end than at the tip end. That means that the grip end is the strongest part of the shaft and the tip end the weakest, which, Wishon says, leads trimming to have different effects: "Cutting more of the tip will have the effect of getting rid of some of the weaker end ...
Should the reduction in length be made from the grip end only?
"If the goal in making the clubs shorter in length is a desire to gain an improvement in accuracy, the reduction in length should be made from the grip end only ," Wishon said.
