Some manufacturers provide in-between flexes (R+, S+, R/S combo) for players to get a closer match. As a shaft bends during the loading and downswing, so does the head rotate through the swing. Choosing the proper flex allows head to come back to square position, thereby transferring the maximum amount of energy to the ball at impact. // Length
Full Answer
How do I reshaft my Irons?
Here's how to reshaft your irons, a way that can both improve your golf game and save you a lot of money. Remove your old shafts. If they are made of steel, place one in a vise, then tighten it. If there is a plastic ferrule where the club head meets the shaft, wrap it in a wet paper towel to keep it from burning.
Do you have the right flex shafts in your Irons?
As you can see, there are so many options for the flex of your shaft that there will be something out there for your swing. 80% of golfers fit into a regular or stiff shaft so you are probably going to be fitted with one of them. If you’re not sure that you have the right flex shafts in your irons then book yourself some time with a club fitter.
How to choose the right shaft for your golf clubs?
The more force you create in your golf swing (higher swing speed) the stiffer you will want your shaft. When it comes to iron shafts, the options of what you can play is growing but not as fast as it is in graphite shafts.
Should I use graphite or steel shafts in my Irons?
Graphite or steel for your irons? This depends on you fast you swing the club, I believe that people who swing the club fast (players who use stiff shafts and stiffer) should use steel in their irons. However, players on the regular side of the spectrum can gain a lot of club head speed by using graphite.
What does S stand for on a golf club shaft?
stiff flex"S" denotes "stiff flex" (might also be designated "Firm") "X" denotes "extra stiff flex" (might also be designated "Tour")
What is a parallel Iron shaft?
Parallel-tip shafts are the same, within the model type, for each iron but are trimmed to fit the length for each club. As a result, parallel-tip shafts are heavier in the longer irons and weigh less in the shorter irons.
What is an S flex shaft?
Firm Shaft More commonly known as the stiff shaft (S), this flex is favored by golfers who have a fairly fast swing and drive the ball 250 yards on a consistent basis. Golfers who play a firm or stiff shaft have club speeds between 90-105 mph.
Can you switch shafts on irons?
If you're thinking about changing the shafts on your golf clubs, you can either do them yourself or take them to your local golf shop.
How do you tell if a shaft is parallel or tapered?
0:173:29Differences Between Taper Tip & Parallel Tip Iron Shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you see something labeled as a 355 tip iron shaft you know that's a taper tip product whereasMoreSo if you see something labeled as a 355 tip iron shaft you know that's a taper tip product whereas parallel tip shafts or in that tip.
What is the difference between tapered and parallel shafts?
The difference between a parallel tip shaft and a taper tip shaft is the tip diameter and shaft weight. All golf shafts taper from the butt to the tip, but parallel tips stop tapering below the last step, while the taper tips, continues to narrow.
What happens if shaft is too stiff?
There are a few tell tale signs that your shafts are too stiff, firstly you will lose the ball to the right, because the shaft is to stiff it will be hard to square up at impact, causing the face to be open when you hit the ball, this is going to produce a fade or slice shot, generally ending up on the right side of ...
How far does Tiger Woods hit a 7-iron?
And when it comes to how far Tiger Woods, arguably the greatest iron player of all time, hits his irons? Tiger hits his 3-iron a 'carry' distance of 240 yards on average while his 4-iron goes 225 yards and 5-iron 210 yards. When it comes to his mid-irons he hits his 6-iron and 7-iron 195 and 180 yards.
When should I switch from stiff to regular irons?
If you have a slower swing speed, you are probably going to want to choose regular shafted clubs because the additional flex will provide a little more power and accuracy. When you swing harder, the stiff flex will be more controlled and give you the punch you need to hit better shots.
Is it worth Reshafting my irons?
Reshafting is just one way to keep your clubs performing at a high level. You can also benefit from regripping your clubs. Replacing worn-out golf grips can help make your clubs feel new again. Adding the right shaft to your favorite clubs can get you back on the course and working toward a new personal low round.
How stiff should my iron shafts be?
In general, golfers with driver swing speeds over 95 mph should play stiff flex shafts, and those under 95 mph should play regular flex. Shafts also come in extra stiff (105+ mph) and senior flex (under 85 mph).
Are steel shafts better than graphite?
Typically, steel shafts are much heavier, more durable and are generally less expensive than their graphite counterparts. They are more often than not made from stainless steel and they tend to weigh in between around 90g-120g. Torque or lateral twisting found in all graphite shafts is lower in steel irons.
Are Pxg irons taper or parallel?
PXG GolfWeight0.05 lbsFerrule I.D.355 Taper Tip, .370 Parallel Tip
How do you trim parallel shafts?
0:113:03Golf Tips : How to Trim Golf Club Shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipGood measuring stick a marking pin will need a chop saw that we can chop with and we'll also need aMoreGood measuring stick a marking pin will need a chop saw that we can chop with and we'll also need a grinder just to trim off the burner off the end of it before the club is reesh aft.
Are all iron shafts the same?
In a traditional iron set - what some have started referring to as "variable-length irons" - each iron in the set is a different length. The irons get shorter as the number gets higher. A 5-iron is shorter than a 4-iron; a 6-iron is shorter than a 5-iron; and so on.
What is a constant weight iron shaft?
Constant weight refers to each shaft in the set being approximately the same weight even though they are different lengths. This is a big issue in creating overall shaft balance in either swing weight or MOI matched sets of irons. Not all factory trimmed iron shaft sets are tapered, some are parallel.
Why is it that we are the only golf club manufacturer who uses this approach to shafting?
Why is it that we are the only golf club manufacturer who uses this approach to shafting? Simply stated – cost versus profit. Our proprietary Shaft Optimization Process adds numerous additional steps and associated costs into the club building process that no other brand wishes to incur. However, our goal has always been to produce the highest performance golf clubs in the industry, and we will always do whatever it takes to achieve this goal.
When the shaft is correctly oriented in respect to its inherent flex plane, it will resist twisting to any other?
When the shaft is correctly oriented in respect to its inherent flex plane it will resist twisting to any other position when placed under load and will remain stable through impact. It is as if the club-head is riding on rails through the impact zone.
What is shaft flex?
There is no standardization in the golf industry as to shaft flex which means that one brand’s stiff flex shaft might be the equivalent of another brand’s regular flex shaft, and a particular brand’s regular flex shaft might be the equivalent of another brand’s senior flex shaft, and so on.
What shaft did Jack Nicklaus use?
There is a story concerning Jack Nicklaus where he bent his #8 iron (his favorite iron) during a tournament round. He took it to the tour van to replace the shaft and told the technician that it was a stiff shaft. Upon testing, the technician told Jack that it was, in fact, a regular flex shaft. Jack berated the technician for a few minutes that he should ever question him in the matter of golf so, in the end, the technician put in a stiff shaft. Jack came back later and complained that the club did not feel right and that the technician had screwed up, so the technician went ahead and replaced the shaft with a regular flex shaft without telling Jack. After winning the tournament Jack came back and praised the technician for a job well done.
How to determine flex of a unitized shaft?
The flex of a unitized, parallel tip shaft is determined by how much to trim off the tip of the shaft based on the weight of the head. As head weight increases, the amount of tip trimming increases incrementally to maintain the flex the manufacturer designed into the shaft.
What is soft stepping on a parallel tip shaft?
Soft stepping on a parallel tip shaft is simply the process of trimming less than what the manufacturer suggests. For example, if you have a 5-iron, you tip trim the shaft like a 4-iron. This is called soft stepping once and would decrease the stiffness by a quarter flex. Soft-stepping twice would be cutting the shaft as a 3-iron ...
Is a taper tip shaft hard stepped?
The concept of hard stepping a taper tip shaft is just the opposite of soft stepping. However, this is rarely done because you run out of raw lengths when you get to your shorter scoring irons and wedges. If you examine the row labeled "hard stepped once", notice the 9-iron and wedge entries.
Can you tip trim a long iron?
Secondly, if you have a long iron or hybrid, you cannot tip trim less than zero which will not maintain uniformity in the set. In the example above would affect the 2-iron by soft stepping once or the #2 and 3-iron by soft-stepping twice.
Is a 39.5" shaft stiffer than a 4" shaft?
The 39" 5-iron shaft is not only shorter, but stiffer than the 39.5" 4-iron shaft to offset the heavier weight. Therefore, if we placed the 39.5" 4-iron shaft into the 5-iron (or soft stepping once), then the club will become more flexible. Soft stepping twice would be placing the 40" 3-iron shaft into the 5-iron.
What type of shaft is used for irons?
You have three main choices when it comes to your irons. You have the classic steel shaft, the graphite shaft or the innovative SteelFibre (a graphite shaft surrounded by a very thin layer of steel fibre).
What is the difference between a stiff shaft and a regular shaft?
The main difference is that a stiff shaft is harder to bend than a regular shaft . This is usually created by adding more material to make the shaft up which can often also make them slightly heavier. The more force you create in your golf swing (higher swing speed) the stiffer you will want your shaft.
Who should use stiff flex irons?
The starting point for this is swing speed, if you swing your driver between 90-105 mph then you will probably need a stiff shaft. This will benefit you by delivering great control of your club during your swing and stop you spraying it everywhere. Also taller players using longer clubs require stiffer shafts as they have a longer lever with the clubs.
How will flex affect distance, trajectory and accuracy?
If you have a shaft that flexes too much you are likely to hit high hooks as the club can’t handle your speed. If you have a shaft that is too stiff for you, you will hit low slices as you can’t move the club fast enough.
How fast can a golf driver swing?
Elite golfers can create swing speeds that far exceed what is on the chart above and so they require stiffer shafts. On top of stiff you also have extra-stiff which would be for swing speeds over 105mph. When some tour golfers swing the driver they can generate 115mph and more, some even exceed 120mph!
What do people brag about in golf?
In golf there are a few things that people like to brag about around the club. How far they hit a driver, how high their swing speed is and what their handicap is to name a few. However, another that people use as a bragging point is the flex of their shaft. This can get tiresome and it can mean that some golfers play a shaft ...
Why are wedges stiff?
Interestingly, most wedges on the market have a stiff shaft to maximise control of these more attacking shots. If you’ve ever seen that the shaft on your wedge states that it is “wedge flex” it is actually stiff and they just don’t want to spook you if you’re a regular flex golfer.
How to make steel iron shafts?
There is two primary ways to manufacture steel iron shafts. 1.SEEMLESS CONSTRUCTION. A Seamless shaft starts out as a large cylinder of solid steel, which is heated and pierced with a special machine, turning the solid steel into a large, thick-walled tube. Over a series of stretching operations on very specialized machines called draw benches, ...
What shafts are used in the PGA Tour?
True Temper shafts have been #1 on Tour every week since official equipment counts were started on the PGA Tour, more than 90% of the field will rely on True Temper s hafts in their clubs. Teur Temper shafts have won more tournaments worldwide than all other shaft manufacturing companies combined.
How is a tube shaft formed?
A WELDED TUBE shaft begins as a flat strip of steel that is coiled and welded into a tube. Through what is called high frequency welding, the two ends of the coiled strip are literally fused together without the presence of a second, different material as in the case of most welding. A machine then removes the excess metal from the outside and inside of the welded tube. Once formed, the tube is stretched down to the required 5/8” diameter in the same procedures used in the forming of seamless steel shafts, with the step-downs formed in the same manner. Once formed into the step pattern dictated by each individual shaft design, the raw steel shafts are heat-treated, straightened and then nickel-chrome electroplated to prevent rusting.
What were golf clubs made of?
The golf shafts were made of wood, normally either hazel or ash, which is a very rigid wood and today used in walking sticks. The shafts were then attached to the head of the golf clubs with a splint and bound tightly ...
When did steel shafts become legal?
1930 the Royal and Ancient Order of Saint Andrews, the golf- decision making body in Scotland, made the steel shaft legal for tournament play. 1941 True Temper introduces the first steel iron golf shaft to offer complete flex categories. 1942 True Temper’s Dynamic line is tested and introduced on the PGA Tour.
When did steel shafts stop being used?
Steel shafts were banned by the R&A until the Prince of Wales used a set at St Andrews back in 1929. Go figure, this forced a rule change in 1930.
What is soft stepping on iron shafts?
Soft stepping a shaft is when you take a 6 iron shaft and put it in a 7 iron head ( as an example) or a 7 into an 8 or 8 into a 9 etc. If you look at the first step on an iron shaft you will see it is farher up from the hosel on a 6 compared to a 7 iron. Basically the section is longer and there for more flexable or a softer flex. This is done in shaft manufacturing because the iron head weights decrease ( get lighter ) from short irons up to long irons. Soft stepping one time equals approx 1/3 weaker flex than standard or stated on the shaft.
How much does the S300 weigh?
The weights get heavier as you got from R-S-X but the weights also overlap. S300 and X100 are both 130g.
Can you use a hard step shaft in a wedge?
Always better to use the stiffer shaft and soft step them....when you hard step DG shafts you end up with the same shaft in your wedge, 9 iron and 8 iron.....NOT exactly optimal.
How to abrade a golf club shaft?
Use sandpaper or a file to abrade the end of the steel shafts that will go into the hosels of your club heads. However, if the shafts are made of graphite, remove the outer coating with a sanding belt before you sand them. If the shafts are a little too fat to fit into the hosels, use a wire drill bit on them until they fit snugly into them.
How to keep a golf club shaft from burning?
If they are made of steel, place one in a vise, then tighten it. If there is a plastic ferrule where the club head meets the shaft, wrap it in a wet paper towel to keep it from burning. Wearing a pair of fire-retardant gloves, heat the hosel of the club head for 30 seconds with a heat gun, then twist the shaft to remove it. ...
How to adjust grips on a golf cart?
Put on the grips. Thoroughly clean the area on the shafts that will be covered by the grips before you wrap it with double-sided tape. Cover the tape with grip solvent and carefully slide each grip down the shaft to the end. Since it takes about 10 minutes for the solvent to dry, you have plenty of time to adjust the grips with your hands.