Remove the rear tire from the driver’s side of the golf cart. Remove the circlip with two clips above the speed sensor. Push the speed sensor in gently and then pull it out from its place.
Full Answer
How do you adjust the speed on an EZ GO golf cart?
Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.
How to remove speed sensor from EZGO TXT PDS golf cart?
The speed sensor of an EZGO TXT PDS golf cart can be removed easily by following a few simple steps as given below. Locate the speed sensor on the golf cart. This is usually present behind the rear tire of the golf cart on the driver’s side. Remove the snap ring or circlip with two clips that hold the speed sensor in place, using a pair of pliers.
What are some of the problems with my EZGO golf cart?
Some problems that you may face with your EZGO golf cart are that the cart creeps along or slows down after starting at a normal pace. These issues could be related to the speed sensor. A faulty speed sensor wiring, a torn speed sensor wire, a broken speed sensor magnet, or a magnet that has slipped out of place can also cause problems.
Can you adjust the governor on an EZ GO spark plug?
Many manufacturers, including EZ Go, do not want consumers tampering with their engines, and have thus hidden the governors in the spark plug ignition. This is very difficult to adjust without ruining the engine, and should be left to trained professionals. How can I stop the choke cable from getting hot on my EZ-GO golf cart?
How do you remove a speed limiter from a golf cart?
0:040:46How to remove governor on a Club Car golf cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the farther you bend that normally the faster it goes and then that's it basically when you wantMoreSo the farther you bend that normally the faster it goes and then that's it basically when you want to return your heart you just bend that back down and go back to normal speed.
How do I make my ezgo golf cart go faster?
One way to increase the speed of EZ Go golf carts is to incorporate an octane booster when you fill the tank. The cart will have more pick-up, and it could gain as much as 5 mph. A different approach is to take out the throttle linkage governor on the carburetor.
How do you change the governor speed on a golf cart?
If you find this rod, then your governor can be easily adjusted by accessing the cart's inner workings. Simply adjust the cable coming from this metal protrusion, turning the nut counterclockwise to make the cable longer, effectively adjusting the cart's governance to increase the overall speed.
How do you turn off the governor on a electric golf cart?
Basically, an electric speed governor can be controlled by a tiny metal rod that's located by the clutch of your golf cart. First things first: The electric speed governor is connected to a cable. You can adjust your speed by rotating the nut in a counterclockwise rotation.
Why is my ezgo golf cart so slow?
A EZGO RXV and TXT golf cart can run slow because of a faulty speed sensor, low battery charge and insufficient levels of water in the battery. A problem with the speed sensor. A faulty speed magnet. One or more batteries could are weak and don't have sufficient charge or the water level could be low.
How do I unlock Freedom mode on EZGO?
Toggle the forward/reverse switch from the "neutral" position to "reverse" five times in quick succession. After a few seconds, the computer controller will beep four times, indicating it has shifted into the freedom mode. Flip the run-tow switch back to “tow” and then "run” to escape the diagnostic setting mode.
Where is the speed controller on an ezgo golf cart?
These speed controllers are located under the EZGO cart seat. Check the speed controller's attachment near the carburetor.
How do you bypass a speed sensor on a golf cart?
The speed sensor on the EZGO golf cart can be bypassed by unplugging it from the speed controller. By disconnecting the J5 pin on the speed controller, this will cause the golf cart to creep along as the controller will go into limp mode.
What does removing the governor do?
Removing the governor will increase the maximum rpm of the engine, but the internal parts of the Predator 212 are designed for 3600 rpm. Generally, this isn't an issue with just the governor removal, the internal parts can usually withstand 5000 rpm without breaking apart (unless you go full throttle for too long).
Where is the governor on a ezgo golf cart?
The engine is in the front of golf carts, underneath this panel. Take off the plastic cover and set it aside with the seats. Follow the thickest cable coming from the gas pedal until your find a small spring wrapped around a metal rod. This is the governor.
How do I turn off speed governor?
1:072:00How to remove your car's speed limiter como sacar limitacion de ...YouTubeStart of suggested clipEnd of suggested clipSelect on that and then. When you press cancel it means you're done and the tune will start toMoreSelect on that and then. When you press cancel it means you're done and the tune will start to upload you'll hear the fan kick on and then when you're all done it'll say the press select to enter.
How can I make my electric golf cart go faster without upgrading?
How to Make an Electric Golf Cart Faster Without UpgradesWash Your Cart Properly. ... Inspect the Batteries. ... Refill the Battery Water. ... Check the Gas Pedal and Linkage. ... Measure the Tire Pressure. ... Charge Up Your Battery Unit. ... Lighten Up Your Cart's Weight.
How to increase speed of EZ Go golf cart?
One way to increase the speed of EZ Go golf carts is to incorporate an octane booster when you fill the tank. The cart will have more pick-up, and it could gain as much as 5 mph. A different approach is to take out the throttle linkage governor on the carburetor.
Do golf buggies have a carburetor?
Many older models have gas powered engines with a throttle and carburetor linkage. Aside from using the accelerator pedal to go slower or faster, there is a variety of options to adjust the speed of these great golf buggies.
Where is the speed sensor on an EZGO golf cart?
The speed sensor on an EZGO TXT golf cart is located close to the motor. This sensor is present on the rear side of the motor on the driver’s side of the golf cart.
Why does my EZGO golf cart beep?
If you hear a rapid beeping sound and resistance to the pushing action because of the regenerative braking action , your EZGO golf cart has a good speed sensor and is communicating with the speed controller. On the other hand, if the cart begins to roll, it indicates that the speed sensor is faulty.
How fast does a PDS golf cart go?
If there is no input from the sensor, the stock controller will make the cart move only at a speed of 2 to 3mph.
Why does my golf cart beep when it goes downhill?
If the golf cart beeps very fast and continuously when it goes downhill, it means that the sensor is communicating with the speed controller. This indicates a faulty controller and replacing it should help.
How to replace a speed sensor magnet?
A pair of pliers can make the replacement easy. Remove the clip holding the speed sensor magnet in place. Pull the magnet out gently using the pliers. Put the new magnet in the same place from where you took out the old one. Fasten the holding clip once again and ensure that it doesn’t slip out of place.
How to change speed sensor on golf cart?
Remove the rear tire from the driver’s side of the golf cart. Remove the circlip with two clips above the speed sensor. Push the speed sensor in gently and then pull it out from its place. Remove the wire connection behind the sensor. Connect the wire to the new speed sensor.
Do you need a voltmeter for an EZGO golf cart?
You will need a voltmeter to assist you with troubleshooting the speed sensor of your EZGO TXT golf cart. The following steps can help you with going about this process.