Push on the base of the hosel with a pry bar to release the head from the shaft. Catch the head as it falls off the end of the shaft. Allow the club head to cool off before installing the new shaft.
How do you remove steel shafts from a golf club head?
Using propane or a torch, heat the hosel of the club to remove the steel shaft from the club head. The heat will break the epoxy bond that holds the head to the shaft.
How to install a golf club head?
Step 1. Tape the club head with masking tape to prevent it from being scratched during installation. Place shaft firmly in the vise. Step 2. Making sure the hosel in the club head is clean, apply epoxy all around the inside of the hosel. Also, apply epoxy around the end of the shaft where the club head goes.
How do you fix a broken hosel on a golf club?
Use a heat gun to heat up the area around the hosel to soften the epoxy glue that connects the shaft to the club head. Push on the base of the hosel with a pry bar to release the head from the shaft. Catch the head as it falls off the end of the shaft. Allow the club head to cool off before installing the new shaft.
How do you epoxy a golf club head?
Making sure the hosel in the club head is clean, apply epoxy all around the inside of the hosel. Also, apply epoxy around the end of the shaft where the club head goes. Gently, push the shaft into the hosel of the club head, turning the shaft at the same time.
How do I change my club heads?
1:4010:45How to replace a golf club shaft - Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipProbably start off on high but you want to move it around on actual the hostile here kind of andMoreProbably start off on high but you want to move it around on actual the hostile here kind of and spinning it around a little bit and make sure you get this superhot.
How do you remove the head from a golf club?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.
How do you reattach a club head?
0:006:41HOW to FIX your GOLF CLUB if the HEAD comes off | Easy TutorialYouTubeStart of suggested clipEnd of suggested clipIf you want to just make sure you're getting the right thing basically just one side hardener. AndMoreIf you want to just make sure you're getting the right thing basically just one side hardener. And one side resin. And they mix together to form a really strong bond.
How do you put a golf club head on?
Golf Club Epoxy. Adhesives are used in many different sports equipment bonding applications. One such application is that of bonding heads onto shafts for golf clubs. It sounds like an easy application and in principle it is – put some adhesive on the tip of the shaft and then insert it into the club head.
How do you remove a club head from a graphite shaft?
0:314:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipThat are commercially available but they do essentially the same thing they securely clamp the shaftMoreThat are commercially available but they do essentially the same thing they securely clamp the shaft. And either push or pull the head straight off that's the key.
What glue is used for golf club heads?
Golf club heads are attached to the golf shaft with epoxy glue. Epoxy is a thermosetting polymer that is a high strength adhesive. Two parts, the resin and the hardener, are mixed together to create a chemical reaction that cures the epoxy to hardness.
How do you attach a driver head to a shaft?
4:297:38How to Install Graphite Golf Shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipRemove the head and place some epoxy inside the hosel dip the tip of the shaft into the epoxy mix.MoreRemove the head and place some epoxy inside the hosel dip the tip of the shaft into the epoxy mix. And then install into the head rotate.
Can you use JB Weld on golf clubs?
Jb Weld can be used on both metal and plastic golf clubs. It is non-toxic and safe to use on most surfaces.
How do you remove iron head shaft?
How To Re-Shaft Your Steel Golf ClubsCarefully clamp the shaft into a vise using a Shaft Vise Clamp. ... When removing steel shafts from clubheads, use a torch to heat the hosel. ... After 30 seconds of heating, with your gloved hands grasp the head and twist/pull the head.More items...
How do you disassemble a golf club?
0:042:32How To Remove A Steel Golf Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also use a heat gun but it's going to take three times as long. The other things that you'reMoreYou can also use a heat gun but it's going to take three times as long. The other things that you're going to need or a club making vice vice clamp some heavy-duty gloves and probably a knife.
How do you remove a putter head?
0:2911:49THE SHOP: How to replace a putter shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then either a small drill bit or a house a cleaning brush to just clean out the hosel when you'MoreAnd then either a small drill bit or a house a cleaning brush to just clean out the hosel when you're done. So that's all you need - oh. And some eye protection because you know let's be safe here.
Should I take my driver head off when flying?
Remove the Heads Removing the club heads decreases the likelihood of the heads getting snapped off in transit, one of the easiest ways of mastering how to protect your golf clubs when flying. Simply wrap the club head in a golf towel or a headcover and store it in an extra pocket of your golf bag.
How to prepare a club head for a new shaft?
Prepare the hosel of the club head for your new shaft by removing the old epoxy from inside it. The easiest way is to first put the club head into a vise , making sure you don't damage it. Then use a hand drill to carefully remove the debris.
How to loosen epoxy on golf club shaft?
Move the plastic ferrule from its position next to the club head to a position up the shaft so that it will be out of the way and won't be damaged when you apply heat. Step 3. Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. ...
How to remove epoxy from golf club?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside. Since the club head can get quite hot, wear ...
How to remove a broken shaft from a vise?
Step 1. Insert the broken shaft into the vise and remove the shaft by using the heat gun to warm up the hosel and loosen the adhesive that holds the shaft in place. Use medium heat for graphite shafts and higher heat for steel shafts. Once the adhesive has started to melt, pull the broken shaft from the hosel, which is where the shaft meets ...
Can you replace a golf club shaft?
Once a golf club shaft has been broken, it cannot be repaired, but it can easily be replaced. Shafts can be replaced at golf pro shops and most golf stores, but it is also a fairly easy project to do yourself. Replacing your own shaft can save time and money, and allow you to try a new shaft without purchasing new clubs.
How to fix a club head that is stuck to the shaft?
Step 1. Scrape off the ferrule at the bottom of the club head's hosel with a utility knife. Place the club into a shaft clamp to hold it in place while you work on the head. Use a heat gun to heat up the area around the hosel to soften the epoxy glue that connects the shaft to the club head.
How to remove epoxy from golf club?
Remove the club from the shaft clamp and tap the butt end of the grip on the floor to push the shaft all the way into the head. Wipe down the hosel with a soft cloth to remove any epoxy residue. Let the epoxy dry for several hours before using the golf club.
What is the hosel on a golf club?
The hosel is the junction point between the head and the tip of the shaft. Check the size with a shaft identification gauge if you cannot find it on the label.
Can you replace a golf club shaft yourself?
It's usually best to consider having shaft replacement done by someone who knows what they are doing. Instead of paying the pro shop the next time you need to change a golf club shaft, save money by doing it yourself at home. Make sure your replacement shaft is the same size as the original or it might not fit inside the club head's hosel.
Instructions
Tape the club head with masking tape to prevent it from being scratched during installation. Place shaft firmly in the vise.
About The Author
Tami Fisher received her undergraduate degree in mathematics, while also receiving a full-ride golf scholarship. She has extensive experience in the golf industry, as well as the employee benefits area. She is a die-hard Kansas basketball fan, and loves all sports.
