
- Determine the hole position. This is done by pacing the distances as set from the pin sheet. Say the pin placement is...
- Now that the hole position is determined, if you are using a twist in or rotating cup hole cutter, hold the cup hole...
- Release the grass plug into the container, wipe off the outside of the cutting cylinder with a towel, carefully...
How to cut a cup hole in a golf hole?
Now that the hole position is determined, if you are using a twist in or rotating cup hole cutter, hold the cup hole cutter 18 to 24 inches above the green and release it. This method cuts a cleaner hole edge than placing the cutting edge on the surface of the green and twisting the cup hole cutter.
Why cut Cup holes on the Greens?
Greens are the most valuable area of any golf course so daily cup hole cutting is an important task. The most valuable areas of a golf course are the greens. Any activity that occurs on the greens should be the most meticulous, cautious and professional activity that transpires any where on the golf course.
How do you cut a 7 inch hole in grass?
Release the grass plug into the container, wipe off the outside of the cutting cylinder with a towel, carefully insert the cup cutter into the new hole, bring the cup cutter to a perpendicular position by centering the level, and then rotate the cup cutter left and right until the 7-inch depth is reached.
How does a greenskeeper cut a hole in a golf course?
He pushes the cutter into the selected spot, then pulls the tool up, removing a plug of turf and dirt from the green. The greenskeeper may then smooth the bottom of the hole to make sure the new cup fits properly.

Do they change the holes in golf tournaments?
During PGA tournaments, hole locations are typically changed each round. This is commonly termed each day's “pin placement.” The USGA, however, disapproves of this term, listing “pin” as one of the top 10 misused golf terms, according to a 2009 article on the USGA website.
How often are the holes moved on a golf course?
It is common to change holes every day on the course, but not as common on the practice green. Leaving holes in the same location for more than a day is inviting a lot of traffic in a relatively small area, thus wearing grass around those holes quicker.
How is a golf course laid out?
It consists of a series of holes, each consisting of a tee box, a fairway, the rough and other hazards, and a green with a cylindrical hole in the ground, known as a "cup". The cup holds a flagstick, known as a "pin". A standard round of golf consists of 18 holes.
How do you cut a putting green hole?
0:487:17Installing Putting Green Cups - Backyard Artificial Grass ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut what I do is I mark the holes. And I put a nail. In the turf and I stand everything and then IMoreBut what I do is I mark the holes. And I put a nail. In the turf and I stand everything and then I come back and I just locate where the nail is. Now. You've got a lot of sand around here and what I
What is an illegal hole placement in golf?
Seriously, though, there is nothing in the Rules of Golf about hole location, so there's no such thing as an “illegal” hole location.
How close to the edge of the green can the hole be?
“We keep hole locations a minimum of five paces – approximately 15 feet – from the edges of a green. Many golfers are not aware that while there are rules about the size of the hole and the depth of the liner, there is no rule about how far from the edge of a putting green the hole must be located.
Why does golf have 18 holes?
Andrews formalized the rules and stated, “One round of the Links, or 18 holes is reckoned a match, unless otherwise stipulated.” Legend has it that the reason for 18 holes is that a bottle of whiskey contained the same number of shots as holes on a course, thus providing just enough drink for a shot on each hole.
What do golfers shout to warn other golfers when they hit an errant shot?
"Fore"—actually, fore! —is a word of warning yelled out by a golfer who hits an errant shot. If your shot is in danger of hitting or landing very close to another golfer or group of players on the golf course, you should yell "fore!" to warn players to watch out.
What is a golf hole called?
Hole A circular hole in the ground which is also called “the cup”, 4.25 inches in diameter.
How deep is the cup of a golf hole?
Golf Hole (Golf Cups) have a regulated diameter of 4.25” (108 mm) and total depth between 4”-6” (101.6-152.4 mm). Golf Holes, or Golf cups, are the ultimate target for hitting the ball into in a game of golf.
How do you cut the green on a golf course?
0:000:51Cutting a Golf Green Part 1 of 2 - LandscapeSafety.com - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhile mowing it is not appropriate to slow the machine. You must keep a constant ground speed whenMoreWhile mowing it is not appropriate to slow the machine. You must keep a constant ground speed when the reels are touching the putting surface.
What goes under artificial putting green?
To make the base for the putting green, put crushed stone, such as 1/4-inch to 3/8-inch unwashed, crushed limestone, into the excavated area. Spread the crushed rocks out evenly with a rake or shovel.
How often do golf courses spray?
To the casual observer, spraying greens every one or two weeks may appear to be overkill. However, short spray intervals allow superintendents to observe putting green performance throughout the season and apply products only at the appropriate time to maximize their efficacy.
Why do golf courses move the hole?
The frequency for changing hole locations is dependent on golfer traffic, turf growth and labor availability. For daily play, the purpose for changing the hole is primarily to distribute traffic over the entire putting surface to prevent wear damage.
How are golf pin placements determined?
Pin Placement Defined The tool extracts a cylindrical chunk of grass and dirt from the green. The cylinder is placed into the former hole's location, and the cup that lined the old hole is positioned in the new spot. During PGA tournaments, hole locations are typically changed each round.
Do Augusta members get greenjackets?
Green jacket Every member of Augusta National receives a green sport coat with the club's logo on the left breast. Members are required to wear them during the tournament, and the jackets are not allowed to be removed from the grounds. The idea of the green jacket originated with club co-founder Clifford Roberts.
What is a cut in golf?
A cut is used to determine which players will make it to play into the weekend and, in doing so, will qualify to receive a check from the tournament based on their place of finish.
What is the cut line for PGA?
The standard cut line for a PGA event after two rounds is the score of the 65th lowest scoring professional. Any players that finish with that score or better are considered to have made the cut and continue play in the weekend rounds.
How many strokes does a golfer have to cut to make the weekend?
Some events utilize a 10-stroke cut rule, under which any player within 10 strokes of the leader after two rounds is permitted to make the weekend, even if the player ranks worse than 65th. This is primarily used in major tournaments, where the course is very difficult and a player who goes out and shoots a score in the mid-60s can climb through the field quickly.
Why is changing holes important?
Changing hole locations regularly is important, not only for variety and player enjoyment but also to preserve the health of the greens. “If you get golfers trampling over and over around the same spot, they really do a number on that part of the green,” Guilfoil says.
When does Guilfoil cut new holes?
At many other properties, though, the frequency depends on a range of factors, including maintenance budgets, turf type and time of year. From early fall, when he overseeds, through June 1, Guilfoil cuts new holes at Desert Canyon every morning. But come summer, he takes Tuesdays and Thursdays off.
Is it illegal to cut holes in golf courses?
The logic behind where golf courses cut their holes, according to a superintendent. There is no such thing as “illegal” hole locations, but there certainly are good ones and bad ones . Location, location, pin location. The golden rule of real estate is also a key consideration for golf-course superintendents.
Is Guilfoil's cup cut on the green?
In the spirit of fairness, Guilfoil always cuts his cups at least one flagstick-length away from the collar, never any closer. Nor does he want a cup cut on a portion of the green with too much slope.
Why are golf holes moved?
First, if the holes weren’t moved the immediate area around each hole would be worn down by the constant use. Additionally, moving the hole locations adds variety to the course.
How deep is a hole in golf?
According to the Rules of Golf, the hole must be 4.25 inches in diameter and a minimum of 4 inches deep. A greenskeeper uses a hole cutter to create a new hole for the green. He pushes the cutter into the selected spot, then pulls the tool up, removing a plug of turf and dirt from the green.
What to do if a plug isn't flush with the putting surface?
Extra dirt may be added to the hole if the plug isn’t flush with the putting surface. To blend the plug in with the rest of the green, the greenskeeper may poke some very thin holes around the plug’s edges, then step on and around the plug. Extra water may also be added to help the plug’s grass remain healthy.
Why do golfers take different approach shots to the green?
Tee shot strategy on par-4 and even some par-5 holes can also change with differing hole locations, because golfers may try to get themselves in position to make a specific type of approach shot.
How far below the putting surface should a cup be?
The cup -- which may be taken from the former hole location -- is then inserted into the new hole, with the cup’s edges at least 1 inch below the putting surface. White spray paint may be added around the edges of the new hole to make it easier to see.
Can you play a hole differently?
A hole may play much differently when the hole placement changes. Moving the hole on a golf green isn’t a very difficult job, but the greenskeeper must pay attention to all the details to maintain the putting surface in top condition.
1. The Plug
First, after they cut a new hole, the maintenance crew uses the hole-cutter to plug the dirt taken from the previous location and plug it into the new hole.
2. The Scissors
In order to keep track of where the exact holes are, the greens crew sprays a small dot on the new location. When that piece of dirt is placed in the previous day’s hole location, the cut that sprayed piece of grass off the green.
3. The Fork
Then, similar to using a repair tool to replace a pitchmark, they use a fork to perform a mini aeration on the bare spot and the surrounding area.
