Golf-FAQ.com

how do you change the drive axles on a 2004 volkswagen golf

by Dr. Ophelia Fritsch MD Published 3 years ago Updated 2 years ago

How do I replace the front drive axle?

Remove the front wheel from the side of the vehicle you are replacing the drive axle on. If you do not have an impact gun you can remove the center cap on the front wheel.

What are the most common problems with drive axles?

The most common problem for drive axles is the tearing of the CV boot. This will cause the CV grease to be thrown out from the CV joint and allow contaminants in. Lack of grease or contaminants in the CV will quickly lead to failure of the joint.

How do you remove a ball joint from a rear axle?

Depending on the age and condition of the tie rod end you may need to use a pickle fork or ball joint remover (red arrow) to separate the ball joint from the bearing housing. By removing the tie rod end and the ball joint the hub now has enough room to move forward while pressing the axle out.

What happens if you don’t Grease Your drive axles?

Your drive axles or drive shafts can wear out over time or get damaged during use. The most common problem for drive axles is the tearing of the CV boot. This will cause the CV grease to be thrown out from the CV joint and allow contaminants in. Lack of grease or contaminants in the CV will quickly lead to failure of the joint.

How do you remove a VW axle?

0:416:19How to Replace Front CV Axle 2006-10 Volkswagen Jetta - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust give it a tap just to loosen the axle up take these three nuts off use a 16 millimeter socketMoreJust give it a tap just to loosen the axle up take these three nuts off use a 16 millimeter socket and i can separate. This slide that out. And slide the axle. Out just twist it to the side.

How do you remove a drive axle?

Loosen the lower ball joint and remove the lower control arm from the steering knuckle. With the old axle nut protecting the end of the axle, tap with axle while pulling the steering knuckle out and away. Remove the nut and slide the axle out the back of the hub.

How do you remove a VW drive shaft?

0:087:15VW Golf Jetta Driveshaft CV Joint Removal Simple Easy StepsYouTubeStart of suggested clipEnd of suggested clipOkay for this CB joint driveshaft removal you're gonna need a 30 mil socket this is a multi-pointMoreOkay for this CB joint driveshaft removal you're gonna need a 30 mil socket this is a multi-point socket which means is it like your normal one it's got loads of points inside.

Can I replace a CV axle myself?

You absolutely can replace your CV axle at home, but you'll need to be at least remotely comfortable using a jack, jack stands, and power tools. Assuming you have most of the equipment already set up in your garage at home, the cost to replace your CV axle will be quite reasonable.

Is it hard to replace an axle?

Replacing a front-wheel-drive axle is straightforward, although physically demanding. Get the replacement axle before you start, as well as a new spindle nut and a cotter pin or two.

How long does it take to replace an axle?

between one and a half to three hoursReplacing a CV axle is a maintenance item that usually takes between one and a half to three hours to complete, depending on the vehicle and if other repairs are needed. A CV axle typically lasts for 70,000 to 130,000 miles, but the axles should be inspected for damage regularly.

How do I remove the inner axle CV joint?

2:183:18How to remove and replace an inner CV joint. VW Passat ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo make sure you use a non marring hammer or something to avoid damaging the joint. Then use anotherMoreSo make sure you use a non marring hammer or something to avoid damaging the joint. Then use another circlet plier to pry this off then slip your new boot on top installation is a reverse of removal.

How do you remove an outer axle CV joint?

0:061:21CV joint removal trick, makes CV boot replacement fast and ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipI've taped this on just so go flying off hold this parallel to the ground and let the axle hang downMoreI've taped this on just so go flying off hold this parallel to the ground and let the axle hang down this trick uses gravity to hold the axle straight and the weight of the axle to knock the joint.

How do you remove a CV axle bolt?

0:591:50A Fast And Easy Way To Remove A Cv Axle Nut Without Impact tools!YouTubeStart of suggested clipEnd of suggested clipGo ahead and spray your CV axle with penetrating fluid or some sort of lubricating fluid. Go aheadMoreGo ahead and spray your CV axle with penetrating fluid or some sort of lubricating fluid. Go ahead and get your wheel and pop the center cap. Off.

What tools do I need to change a CV axle?

Tools and Equipment Needed to Replace a CV AxleBreaker bar.Dead-blow hammer.Drain pan.Jack and jack stands.Large hammer or mallet.Long-handled diagonal cutting pliers.Pry bar or CV axle puller.Ratchet and socket set.More items...•

How do you remove axle without puller?

3:354:54REMOVING AN AXLE SHAFT - Without a Slide Hammer - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhat you're going to do essentially is use your rotor. As a slide hammer. Right. As you see they didMoreWhat you're going to do essentially is use your rotor. As a slide hammer. Right. As you see they did do the trick. It seems violent.

Is CV joint and CV axle the same thing?

A CV axle has two CV joints (an inner joint and an outer joint). These joints allow the axle to transfer the engine's power to the drive wheels at a constant speed while accommodating for the different travel conditions, including the up and down motion of the suspension and cornering.

How do you remove axle without puller?

3:354:54REMOVING AN AXLE SHAFT - Without a Slide Hammer - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhat you're going to do essentially is use your rotor. As a slide hammer. Right. As you see they didMoreWhat you're going to do essentially is use your rotor. As a slide hammer. Right. As you see they did do the trick. It seems violent.

How do you separate axle from hub?

0:190:52How to Remove a Stuck Axle from a Hub Using the OTC Heavy Duty ...YouTubeStart of suggested clipEnd of suggested clipI do is I use a little bit of penetrating. Oil on it spread to help things move then you bolt theMoreI do is I use a little bit of penetrating. Oil on it spread to help things move then you bolt the tool up to the hub here. And as you screw the center bolt in it pushes the axle. Through.

How do you pop out a CV axle?

1:294:23TWO WAYS to remove a stuck CV axle. - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell for that i'm going to use this five pound slide hammer. And an attachment which is designed toMoreWell for that i'm going to use this five pound slide hammer. And an attachment which is designed to remove cv axles it just threads. On like that and then we'll tighten it. Down with the nut.

How do you get a stuck CV axle out of transmission?

0:325:10Removing Stuck CV Axle from HALF SHAFT - SIMPLE - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd that way i can use the the old cv axle as a it's kind of like a slide hammer. And then uh try toMoreAnd that way i can use the the old cv axle as a it's kind of like a slide hammer. And then uh try to get out that way. So bring in my vice grip here just blocking it using this to lock it off.

Like many modern manufacturers Volkswagen shares components and even platforms across its many model lines

This article is based on one of those shared components but the work may have been performed on a different model than your vehicle. While some fasteners and other hardware types and sizes may be different, all of the information you need to safely complete the project is included in this article.

Project Photos

Figure 1 If you do not have an impact gun you can remove the center cap on the front wheel. Leave the car on the ground and insert the 27mm socket through the center (red arrow). Next, place the largest breaker bar you have on the socket and break the bolt loose.

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9