Push on the base of the hosel with a pry bar to release the head from the shaft. Catch the head as it falls off the end of the shaft. Allow the club head to cool off before installing the new shaft.
How do you remove epoxy from a golf club head?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.
How do you replace a broken shaft on a golf club?
Prepare the hosel of the club head for your new shaft by removing the old epoxy from inside it. The easiest way is to first put the club head into a vise, making sure you don't damage it. Then use a hand drill to carefully remove the debris.
How do you remove a ferrule from a golf club?
Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it. Place the club in a vise to position it for shaft removal. The club should lie horizontally. Make sure the vise grips the shaft securely to prevent it from slipping out. Expose the length of the head and about 8 inches of shaft. Heat the glue inside the hosel.
How to reshaft a golf driver?
How to Reshaft a Golf Driver. 1 Step 1. Prepare the tip of the new driver shaft by scraping the paint and polyurethane off with a sharp knife. Make sure you don't cut in to the shaft ... 2 Step 2. 3 Step 3. 4 Step 4. 5 Step 5. More items
How do you remove a driver head from the shaft?
0:314:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipThat are commercially available but they do essentially the same thing they securely clamp the shaftMoreThat are commercially available but they do essentially the same thing they securely clamp the shaft. And either push or pull the head straight off that's the key.
How do you remove a golf iron head from the shaft?
2:217:18Removing an iron shaft by hand - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo how do we do this right so a simple tool burns-a-matic butane torch you can get these at lowe'sMoreSo how do we do this right so a simple tool burns-a-matic butane torch you can get these at lowe's home depot or anything like that they're like 15 bucks very handy little item for around the house.
How do you remove a golf head from a steel shaft?
How To Re-Shaft Your Steel Golf ClubsCarefully clamp the shaft into a vise using a Shaft Vise Clamp. ... When removing steel shafts from clubheads, use a torch to heat the hosel. ... After 30 seconds of heating, with your gloved hands grasp the head and twist/pull the head.More items...
How do you remove a wedge head from a shaft?
As you apply heat to the hosel (by keeping the heat moving around the whole area), you should periodically try and twist the head and shaft. If they don't budge, keep applying heat. Eventually you will feel the epoxy break and will be able to twist the head off.
How do you replace a driver head?
0:045:16Golf Club Repair - Removing the driver head and cleaning & preppingYouTubeStart of suggested clipEnd of suggested clipWe can take the old shaft out of the shaft extractor here pretty easy to get the old shaft out justMoreWe can take the old shaft out of the shaft extractor here pretty easy to get the old shaft out just loosen up the screws. Take the protective film off the shaft. So you don't scratch it.
Can you put a new driver head on an old shaft?
The only way to know if we can put your old fitted shaft into a new head it to pull the shaft, weight the head and test the new head with the old shaft. The head may be heavier or lighter, the hosel dimensions may be off which could cause a length issue.
How are golf club heads attached to the shaft?
Golf Club Epoxy. Adhesives are used in many different sports equipment bonding applications. One such application is that of bonding heads onto shafts for golf clubs. It sounds like an easy application and in principle it is – put some adhesive on the tip of the shaft and then insert it into the club head.
How do you remove a bore through the shaft?
2:1313:16How To pull bore thru Golf Shafts, Golf Club Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd that goes right on over here and it acts as the buffer to pull so I don't dent the top of theMoreAnd that goes right on over here and it acts as the buffer to pull so I don't dent the top of the head with my shaft puller. Ok. So that's what this does.
How do you change golf club heads?
0:272:32How To Remove A Steel Golf Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also use a heat gun but it's going to take three times as long. The other things that you'reMoreYou can also use a heat gun but it's going to take three times as long. The other things that you're going to need or a club making vice vice clamp some heavy-duty gloves and probably a knife.
Should I take my driver head off when flying?
Remove the Heads Removing the club heads decreases the likelihood of the heads getting snapped off in transit, one of the easiest ways of mastering how to protect your golf clubs when flying. Simply wrap the club head in a golf towel or a headcover and store it in an extra pocket of your golf bag.
How do you remove graphite shaft without a puller?
0:353:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain using a butane torch you can actually really focus the heat which is a lot better than sayMoreAgain using a butane torch you can actually really focus the heat which is a lot better than say trying to use a heat gun which could end up damaging. The fibers of the golf shaft.
What to do if your golf club shaft is bent?
If the shaft of your golf club is bent or broken, do not discard the entire club. Instead, remove the clubhead from the damaged shaft and install it on a new one. Disconnecting the golf club shaft from the head also allows you to try the latest shaft technology on the market without purchasing a whole new club.
How to remove ferrule from golf club?
Step 1. Use a utility knife to scrape off the ferrule at the connection point between the shaft and the clubhead. Scrape down toward the head and away from your body.
Step 1
Put on protective gloves and keep them on until the procedure is complete.
Step 2
Heat the hosel (small metal joint linking the shaft to the club head) with a heating gun. Be sure to dispense heat evenly on all sides of the hosel and don't be alarmed if small amounts of white smoke begin to escape the hosel cavity. That is just the old epoxy melting.
Step 3
Place the grip end of the club on the ground so the head end is sticking straight up and gently pull the head off the shaft. Do not twist, especially if you want to reuse the shaft or sell it, as twisting may harm the inner walls of the hosel as well as the tip of the shaft.
Step 4
Allow the club head to cool completely once its been liberated from the shaft.
Step 5
Roll up a small piece of sandpaper and use it to clean out any remaining epoxy residue inside the hosel joint, making it ready for the insertion of a new shaft.
How to prepare a club head for a new shaft?
Prepare the hosel of the club head for your new shaft by removing the old epoxy from inside it. The easiest way is to first put the club head into a vise , making sure you don't damage it. Then use a hand drill to carefully remove the debris.
How to loosen epoxy on golf club shaft?
Move the plastic ferrule from its position next to the club head to a position up the shaft so that it will be out of the way and won't be damaged when you apply heat. Step 3. Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. ...
How to remove epoxy from golf club?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside. Since the club head can get quite hot, wear ...
Step 1
Place the shaft, or what remains of it if it is broken, in a vise parallel to the floor. Secure the shaft in the vise.
Step 2
Apply heat evenly to the hosel for about a minute, using a heat gun or heat torch. This will break down the epoxy that bonds the shaft to the hosel and make removal easier. If you are working with graphite shafts, use a heat gun, not a torch. Wear goggles and protective gloves.
Step 3
Remove heat from the hosel and twist the club head counterclockwise. It should twist off fairly easily. If it does not, apply more heat.
Step 4
Clean out any remaining epoxy in the hosel. Begin using a file and scrape away the residue, then apply a solvent to a small rag and wipe down the interior of the hosel. You may want to push the rag in with the tip of a screwdriver or similar tool.
What does a new shaft do for a driver?
A new shaft can put the wallop back in your trusty driver and have it hitting like a brand-new club. One of the nice things about replacing a driver shaft is that there is generally no tip trimming involved.
How to secure a ferrule on a golf club?
To do this, place a small amount of epoxy on the inside of the ferrule and slide the ferrule onto the shaft, narrow end first. Place your clubhead on top of the ferrule and place the grip end of the club on the floor. Butt down the grip while pushing down on the clubhead to secure the ferrule at the correct depth on the hosel.
How to mix shaft epoxy?
Mix your shaft epoxy on a piece of cardboard with a craft stick. Professional shaft epoxy comes in two parts; mix them together according to the instructions on the epoxy bottles.
Weight
The weight of your shaft is going to primarily affect your distance. A heavier shaft will reduce your clubhead speed and thus the amount of energy transferred into the ball.
Kickpoint
Depending on the kickpoint, your shaft will bend closer to the head or the grip of the club.
Torque
Torque refers to how much the shaft twists. It’s the least talked about feature but still an important one to club fitters. High torque shafts can twist easily, and low torque shafts are resistant to twisting.
Cost
It always comes down to price at the end of the day and we are always looking for the best deal. A driver shaft can cost anywhere from $40 – $300.
Conclusion
Fitting yourself for a driver shaft is a bit like trying to do your own plumbing. You could do it yourself but if you get something wrong then you might end up in the water.
