Name Plate - Right behind the name plate are two snap nuts on the mounting studs. You can use a small, flat blade screwdriver to remove these. If they prove to be troublesome, you can use a pair of dikes to remove ONLY the snap nut.
What is the front end alignment for a 2001 EZGO TXT golf cart?
The front-end alignment for a 2001 EZGO TXT golf cart can be done using the steps given below. Take center-to-center measurements on the front and rear of the front tires. The front measurement must be lesser than the rear measurement by 1/8 to 1/4 inches.
What to do if your EZGO golf cart has a wobbly front wheel?
You can try out the following steps on a 2006 gas EZGO golf cart that has a wobbly front wheel. Jack up the golf cart to lift the front wheels off the ground. Try shaking the tires from side to side and top to bottom. If you’re able to shake the tires both ways, it indicates that the wheel bearings need tightening.
How do you adjust the tie rods on an EZGO cart?
This can be done by adjusting the ends of the tie rods. Often, a 1/16 to 1/8 inches toe-in adjustment works well for EZGO carts. You should also consider checking the pressure of the tires and centering the steering wheel.
How do I do a front wheel alignment on a TXT?
If both measurements are not the same, it indicates that the front weld-mount axle has shifted. The front wheel alignment for a 1999 EZGO TXT electric golf cart can be done by following the steps given below. Position the golf cart so that both the front wheels are pointed straight.
How do you remove the front cowl on a EZGO RXV?
1:442:57EZGO RXV Front Cowl Removal How-To - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay now that we got the two bolts on the side before out across the top we just grabbed home toMoreOkay now that we got the two bolts on the side before out across the top we just grabbed home to this front Cal it pull it on out keep in mind here. And on the other side is a little clip.
How do you remove vinyl decals from a golf cart?
0:031:04How to remove a golf course number decal from your golf car - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd simply warm up the decal to soften the adhesive. Once that's warm you can just find an edgeMoreAnd simply warm up the decal to soften the adhesive. Once that's warm you can just find an edge normally you start on a corner. Pick that edge carefully.
How do you take apart an EZGO golf cart?
6:569:35EZGO TXT Body Removal | How to Remove Golf Cart Body | Episode 1YouTubeStart of suggested clipEnd of suggested clipAcross the backyard you've got four little round tabs these tabs have to be pried out and then underMoreAcross the backyard you've got four little round tabs these tabs have to be pried out and then under each one is a 7/16 bolts we'll take those out and get started we're just about done now.
What does TXT mean EZGO?
EZGO launched the RXV models in the year 2008. The TXT golf carts date back to 1996 and its production by EZGO continued till 2013. For those not familiar with the acronyms, TXT is the acronym for Textron the company manufacturing these golf carts. RXV stands for Rear Crossview Mirror.
How do you remove vinyl lettering?
0:021:16Quick Tips - How to Remove Vinyl Lettering - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply apply heat with a heat gun hair dryer onto the surface of where you're trying to remove. TakeMoreSimply apply heat with a heat gun hair dryer onto the surface of where you're trying to remove. Take your chisel on the side with this the shiny edge dig under the letter.
What is the best decal remover?
The Best Adhesive Removers for Eliminating Tough ResiduesGoo Gone Original Liquid Surface Safe Adhesive Remover. ... 3M General Purpose Adhesive Cleaner. ... Elmer's Sticky Out Adhesive Remover. ... un-du Original Formula Remover. ... Uni Solve Adhesive Remover Wipes.
How do you speed up an EZGO electric golf cart?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
How do I speed up my EZGO gas golf cart?
One way to increase the speed of EZ Go golf carts is to incorporate an octane booster when you fill the tank. The cart will have more pick-up, and it could gain as much as 5 mph. A different approach is to take out the throttle linkage governor on the carburetor.
How do you remove an armature from a golf cart motor?
0:301:56How To Remove The Motor Armature - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what you want to do is get a hammer just like this and a flathead screwdriver. You want to justMoreSo what you want to do is get a hammer just like this and a flathead screwdriver. You want to just tap on the end no the front end. Oh. Coming out you guys what a wiggle. The armature gently.
How do you tell if my EZGO is a txt?
Where your manufacturer's code is located generally tells you which EZGO model you have (i.e.: TXT, RXV, Marathon, etc.). On many of the newer EZ-GO's, they will have the words "TXT", "Freedom TXT", "RXV" or "Freedom RXV" listed on the side of your golf cart.
What year did EZGO TXT come out?
19966. TXT (1996 to Present)
How do I know if my EZGO golf cart is a txt?
0:356:50How to tell what EZGO TXT you have. EZGO Lingo - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then there for a while they came out with the dcs which is a drive control system the way youMoreAnd then there for a while they came out with the dcs which is a drive control system the way you can tell if you have a dcs is you will have a lever under your legs.
How do you remove stickers from golf clubs?
How To Remove Stickers From Golf Clubs (Step-by-Step Guide)Step 1: Gather Supplies. The first step in this process is to make sure you have everything you need in place before starting the removal process. ... Step 2: Heat Up Sticker. ... Step 3: Peel Sticker. ... Step 4: Wipe With Grip Solvent. ... Step 5: Dry.
How do I remove my ezgo emblem?
0:001:08How to remove an E-Z-GO golf cart emblem - YouTubeYouTubeStart of suggested clipEnd of suggested clipThat nut is in this particular case a ten millimeter. So you have to reach underneath the back sideMoreThat nut is in this particular case a ten millimeter. So you have to reach underneath the back side of the emblem in order to loosen that nut. So just find where that is now taking your tool.
Where are the hinge plates on a car?
Seat Hinge Plates - After removing the seat from the car, you will notice the hinge plates that hold the seat on the car. Each one has two rivets that need to be drilled out with the same bit from earlier. There is also one rivet between each plate, right above the shift handle. Drill that out also.
How to remove a rear bag well?
The best method for removing them is to use a chisel and hammer. Remove the head of these, and a punch to remove the bodies. Remove all 4 of these lower rivets this way. Rear Bag well - There are two drive rivets to be punched out. These are located in each corner of the rear section of the bag well.
How to remove Phillips head bolts?
There are two Phillips head bolts on each plate. Use a screwdriver and a 7/16" combination wrench to remove each one. You may need to soak them down with WD-40 for several hours first. If one breaks, you can get a replacement from your local dealer.
How to remove snap nut?
You can use a small, flat blade screwdriver to remove these. If they prove to be troublesome, you can use a pair of dikes to remove ONLY the snap nut. The name plate can now be removed, thereby exposing the two rivets beneath it. Drill those two rivets out with the same 3/16" drill bit.
How to run a golf cart?
Turn each wheel around and mark a line around the tire circumference in the middle of the tread pattern. Bring the vehicle to rest on the ground and ensure that the tires are positioned pointing straight ahead. Move the golf cart forward by about five feet so that the tires are in the usual running position.
How to make a golf cart spin?
Use a crayon or chalk and draw a circle on one of the front tires in the middle of the thread as it’s spinning. Repeat the above step for the other front tire as well. Rest the golf cart on the ground and move it forward or backward by a few feet. Measure the distance between the lines on the front and back of the tires.
Why does my EZGO RXV shake?
The front end of an EZGO RXV may shake or vibrate due to one or more reasons. You may have an improper toe-in adjustment or there may not be sufficient pressure in the tires. You can do the following if the front end shakes when an EZGO PCS cart moves at a relatively high speed.
How to check if golf cart tire is bulging?
Jack up the golf cart in such a way that only a single end is lifted at a time with just enough ground clearance. Keep a spray can or any object with a straight edge at a distance of about 1/8 inches from the tire to check if it has bulges on the side.
How to check alignment on a cart?
Spin the front wheels using your hand. You can also check the alignment when they are in the air. Use a crayon or chalk and draw a circle on one of the front tires in the middle of the thread as it’s spinning.
Why do you need front end adjustments on a golf cart?
Front end adjustments for most golf carts are needed because of damaged parts like bent A-arms or bent or worn out tie rods as well as worn out bushings.
How to tighten tie rods?
To do this, you’ll have to turn the rods either counterclockwise or clockwise. If the rods feel snug, pour some penetrating oil on them. Tighten the nuts on either end of the tie rods and take a re-measurement to ensure that nothing has moved out of place. Grease the steering gear, spindles and ball joints.