At this point, you need to find the wheel cover on the rear wheels and use your slotted screwdriver to remove it properly. Typically, there should be a few slotted areas where you can slide this screwdriver beneath the cover and carefully pry it off to get easy access to the wheel. Don’t force the cover off with a lot of pressure.
- Remove the rear wheel of the golf cart.
- Take off the brake drum from its place.
- Insert a 90-degree snap ring pliers through the holes in the hub and remove the snap ring.
- Slide the axle out of its position.
How do you remove the rear axle of a club car golf cart?
You can remove the rear axle of a Club Car golf cart by taking off the snap ring that is located behind the hub. Remove the rear wheel of the golf cart. Take off the brake drum from its place. Insert a 90-degree snap ring pliers through the holes in the hub and remove the snap ring. Slide the axle out of its position.
How to remove axle shaft on a club car DS?
You will need a few chocks, a pair of 90-degree internal snap ring pliers, a floor jack and jack stands to remove the axle shaft on a Club Car DS. The steps given below can help you to take off the axle shaft from the golf cart.
What causes a drive axle to fail on a golf cart?
The drive axle for a golf cart rarely fails because of the low power of the motors. You may need to remove one to change the bearing or if a gear is stripped.
Where is the retainer nut on a 1998 club car rear axle?
If the groove that houses the ring is damaged with a burr on the edges, you can use the edge of a small three-sided file to knock off the burr. This is often helpful when the axle is installed. The axle bearing of a 1998 electric Club Car rear axle houses a retainer nut that is located inside the axle tube.
How do you remove a golf cart axle?
1:592:59How to Remove an E-Z-GO TXT Front and Rear Axle - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe first step is to remove the rear pin from the brake cable once this is done remove the c-clipMoreThe first step is to remove the rear pin from the brake cable once this is done remove the c-clip and slide the brake cable from the assembly.
How do you remove a rear shaft?
1:1011:06How to Remove Rear Axle Shafts and Replace Outer Seals ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's back and it came off easily. Okay so we're kind of holding everything together here pull thisMoreIt's back and it came off easily. Okay so we're kind of holding everything together here pull this out then the pin.
How much does it cost to replace a rear axle?
The average to repair a front axle is $550 dollars. Rear axle repair costs run a little higher and average about $799 dollars.
How do you grease a golf cart wheel bearing?
0:307:15How To Grease Wheel Bearings - 2 Easy Methods - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just put some grease in the palm of your non-dominant. Hand now take the bearing and you'reMoreAnd just put some grease in the palm of your non-dominant. Hand now take the bearing and you're gonna press it in. So when you get these wheel bearings you need to grease these.
How do I remove an axle?
2:107:50How To Remove A CV Axle– AutoZone Car Care - YouTubeYouTubeStart of suggested clipEnd of suggested clipA regular pry bar can be used to break the joint loose.MoreA regular pry bar can be used to break the joint loose.
How do you remove an axle shaft?
3:338:33Step by Step: How to Replace Axle Shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipSeparate the strut from the lower control arm this will be necessary to remove the axle shaftMoreSeparate the strut from the lower control arm this will be necessary to remove the axle shaft position a drain pan under the vehicle to catch any oil that might come out of the transmission.
How do you change a rear axle?
0:483:38How to Replace Rear End on Your Car (Differential) - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust put one on each side so it's even then basically you on bolt everything you take the driveshaftMoreJust put one on each side so it's even then basically you on bolt everything you take the driveshaft off the back. Then you pick up the back seat.
How long does it take to replace an axle?
between one and a half to three hoursReplacing a CV axle is a maintenance item that usually takes between one and a half to three hours to complete, depending on the vehicle and if other repairs are needed. A CV axle typically lasts for 70,000 to 130,000 miles, but the axles should be inspected for damage regularly.
How do you change an axle?
4:427:08Fastest and Easiest Way to Replace a CV Axle - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn the transmission. So when you go to put this in you want to make sure you put it straight. AndMoreOn the transmission. So when you go to put this in you want to make sure you put it straight. And you push it all the way in I find that this way is to push it from me once she wants to sing gate.
Where are the grease fittings on a Club Car golf cart?
0:282:10Club Car Golf Carts - Lubrication Schedule - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're going to want to actually feet see how the grease comes out of there fitting. Watch when IMoreYou're going to want to actually feet see how the grease comes out of there fitting. Watch when I push this see how it comes out you want to be able to see grease coming out of the fitting.
What happens if you over grease a bearing?
Too much grease volume (overgreasing) in a bearing cavity will cause the rotating bearing elements to begin churning the grease, pushing it out of the way, resulting in energy loss and rising temperatures.
How do you remove the club car from a DS rear axle?
How do I remove the rear axle on a Club Car golf cart?Remove the rear wheel of the golf cart.Take off the brake drum from its place.Insert a 90-degree snap ring pliers through the holes in the hub and remove the snap ring.Slide the axle out of its position.
How to remove the rear wheel of a golf cart?
Remove the rear wheel of the golf cart. Take off the brake drum from its place. Insert a 90-degree snap ring pliers through the holes in the hub and remove the snap ring. Slide the axle out of its position. You may require a slide hammer to help you with releasing the bearing from the axle if it’s stuck on to it.
How to remove rear axle seal on 2002 Club Car DS?
In a 2002 Club Car DS, you can remove the rear axle seal from the axle opening by popping it out using a seal puller. If you want to install a new axle assembly, you’ll have to do the above steps followed by fitting the new assembly in place and redoing these steps once again in the reverse order.
How to remove the shaft on a club car DS?
How to remove the axle shaft on Club Car DS. You will need a few chocks, a pair of 90-degree internal snap ring pliers, a floor jack and jack stands to remove the axle shaft on a Club Car DS. The steps given below can help you to take off the axle shaft from the golf cart. Keep the chocks before the front wheels of the Club Car.
How to remove rear axle snap ring?
You can remove the rear axle snap ring on a Club Car using a pair of 90-degree snap ring pliers and a flashlight. Take off the rear wheel from the Club Car golf cart. Remove the brake drum from its place.
How to tell if rear axle bearing is bad?
The most common giveaway sign of a bad rear axle bearing is a loud noise coming from the axle assembly. You can try one of the following tips to solve the problem.
Where is the C clip on a golf cart?
You can also check for a C-clip at the backside of the golf cart that keeps the axle in position. This clip is often inside the axle tube behind the drum mounting flange.
Where is the retainer nut on a 1998 Club Car?
The axle bearing of a 1998 electric Club Car rear axle houses a retainer nut that is located inside the axle tube. This is often a C-clip and keeps the axle in position inside the tube. This C-clip or retainer nut can be accessed only using a pair of 90-degree C-clip pliers.
Why does my golf cart drive axle fail?
The drive axle for a golf cart rarely fails because of the low power of the motors. You may need to remove one to change the bearing or if a gear is stripped.
How to tighten a golf car bearing?
Screw the bearing puller into the center of the axle and wrap its arms around the back bearing housing. Tighten the bearing puller until the bearing is released. Pull the axle from the golf car with your hands. Some bolts may be locked in place because of their age.
When was the golf cart invented?
The golf cart was invented in 1962 by Merlin L. Halvorson. The golf cart allows golfers a more relaxing way of getting around the course verses walking and carrying their clubs. Like all mechanical devices, golf carts require maintenance and repair to operate properly.