How do I install kingpin bushings?
0:473:39Meritor FastSet No-Ream King Pin Kit Installation Video - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo begin the installation twist the new spiral bushings in clockwise. Start by hand at a slightMoreTo begin the installation twist the new spiral bushings in clockwise. Start by hand at a slight angle then use a t-handle tool continue installing until the bushing is below the top of the bore.
How do I check my kingpin bushings?
2:446:29HOW TO CHECK KING PINS - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what you do to check these okay. It's just take up on the push up on the tire. Pull on the tire.MoreSo what you do to check these okay. It's just take up on the push up on the tire. Pull on the tire. Okay. If you get any more than about a quarter inch a half inch of play in. There.
How do you get a stuck kingpin out?
1:168:13How to Remove KINGPINS! - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf it takes too much force to hit eat it up the axle with the torch heat up the kingpin area withMoreIf it takes too much force to hit eat it up the axle with the torch heat up the kingpin area with heat up the axle with the torch.
What is kingpin kit?
King pin kits are composed of king pins as centrepiece of the steering knuckle, slide bearing bushings and roller bearings. Depending on the area of application, the kits are additionally equipped with oil seals, thrust washers, o-rings, shims and lubrication nipples.
How do I know if my king pins are bad?
Signs of king pin wear or damage include uneven front tire wear, incorrect vehicle alignment, and a pull in the steering.
How do I know if my king pins are worn out?
You will notice signs of kingpin and bushing failure from incorrect vehicle alignment, premature and uneven front tire wear, and rough handling. Experiencing these symptoms while driving may result in a shaking cab or steering wheel.
How do you remove kingpin bushings?
7:3838:20How To Replace Kingpin Bushing And Assemble An Early Ford Front ...YouTubeStart of suggested clipEnd of suggested clipThrough. That quick so the key is to get one or two good hits to make sure you're very square. AndMoreThrough. That quick so the key is to get one or two good hits to make sure you're very square. And hitting straight down and that will kind of get it moving once it gets moved.
How do you remove a kingpin semi?
0:5111:39kingpin replacement on big truck - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow these can be kind of stubborn sometimes I leave nut on they back the end of the threads out justMoreNow these can be kind of stubborn sometimes I leave nut on they back the end of the threads out just a little past the end of the bolt. Then I use a drift. And a hammer and that will come right out.
How do I remove kingpins from my f100?
4:2710:031963 Ford F100 F250 Remove & Install Kingpins Straight Axle Truck ...YouTubeStart of suggested clipEnd of suggested clipReal easy make sure you put jack stands on your rig. Put a couple blocks. In the back so it doesn'tMoreReal easy make sure you put jack stands on your rig. Put a couple blocks. In the back so it doesn't roll just a little safer.
How long does it take to change kingpins?
6-8 hoursA kingpin replacement generally takes 6-8 hours.
How do I install kingpins?
0:092:57King Pin Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut the cup washer on the pin itself. The next item that goes on is the felt washer. So the feltMorePut the cup washer on the pin itself. The next item that goes on is the felt washer. So the felt washer will go on here the felt washer is what keeps the grease from riding up the king pin.
Where do kingpin shims go?
If excessive play is present, the spindle can be shimmed by removing the King Pin and placing one or two of the thin shims between the upper side of th axle and the upper spindle boss. The number of shims needed will be different from car to car and even side to side.