- Switch OFF the golf cart’s engine.
- Reach to where the drive belt is located and use your fingers to press the drive belt between the two clutches.
- The belt must deflect at least one and a half inches under the pressure of your fingers.
- If it doesn’t yield, the drive belt is too tight. If the deflection is more than 1½ inches, then the belt is too loose and it is recommended that you ...
How to properly drive a golf cart?
- When you go for your backswing, you should shift your weight backward. This will give your swing more power.
- A lot of times your instinct might be to have a fast backswing thinking that it will give you more power to crush the ball. ...
- Stay flat. ...
- Take a steady backswing and pause at the top to reset before begin your downswing. ...
How to change drive belt on EZGO golf cart?
The removal of the drive belt on a Club Car golf cart involves a series of steps as given below:
- Turn the Forward/Reverse handle to Neutral.
- Chock the wheels of the cart.
- Disconnect the battery by removing the negative cable first, followed by the positive.
- Disconnect the spark plug wire from the plug.
- It would be better to wear gloves when you do this.
How to adjust the drive belt?
The Process To Adjust Husqvarna Self-propelled Lawnmower
- Adjusting the drive control. ...
- Step #1: Disconnect Power Cable. ...
- Step #2: Adjust Lawn Mower Speed. ...
- Step #3: Test Lawn Mower Speed. ...
- Step #4: Change The Belt. ...
- Adjusting the cutting height. ...
- Step #1: Adjust The Adjusting Lever. ...
- Step #2: Increase The Deck Height. ...
- Step #3: Reduce The Deck Height. ...
- Adjusting the drive pulley. ...
Does my golf cart need seat belts?
Typical golf carts are designed and manufactured to meet an ANSI (American National Standards Institute) safety standard which limits the maximum speed to 15 mph and does not require (or prohibit) seat belts. It is worth noting however, that this ANSI safety standard was written entirely by a committee of the major golf car manufacturers.
How loose should drive belt be on golf cart?
The drive belt should not be too tight. If it's too tight it can risk wearing off faster and it's also harder to shift gears. To check if your drive belt is set just right make sure your golf cart is turned off then check the drive belt by pressing it down between the two clutches with your finger.
How do you tighten the belt on a Club Car golf cart?
Slide the old drive belt off the front drive clutch pulley, and then the rear clutch pulley. Slip the new belt around the golf cart's clutch pulley, and then stretch it out over the front pulley. Pull the front pulley forward slightly to increase the belt tension, and then tighten the tension bolt with the wrench.
How do I adjust my drive belt?
0:591:57Checking and Adjusting a Drive Belt // Supercheap Auto - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll also need a pry bar a middle bar you can use as a lever to apply tension on the belt. LoosenMoreYou'll also need a pry bar a middle bar you can use as a lever to apply tension on the belt. Loosen the adjustment fastener. Then wedge the pry bar between the alternator.
How do you adjust the belt on a EZGO gas golf cart?
And EZGO is no different – there are no screws, knobs, or any other type of adjustment item that you can use to tighten up your belt. Once the belt is one, it has the same tightness and can only be changed if you swap the belt for another one either the proper length and width for your specific cart engine.
How do I know if my golf cart belt is too loose?
0:012:00How to Check the Belts in your Gas Golf Cart | Golf Cars UnlimitedYouTubeStart of suggested clipEnd of suggested clipDown below and you don't want to press the moderate pressure on that belt you're gonna want to seeMoreDown below and you don't want to press the moderate pressure on that belt you're gonna want to see about 3/16 to 1/4 inch of deflection. There no more than that that'll be your proper.
Can you adjust a golf cart clutch?
If you are unsure about removing the drive belt or the clutch, then you can adjust it. Just take out the belt and wound it again with the secondary clutch according to the requirements, and your problem should be fixed.
How do you measure a drive belt tension?
Belt tension is measured by plucking the belt span while holding a sensor close by. Belt tension is adjusted until the belt span frequency, or measured tension level is within manufacturer's recommendations.
How do you tighten a belt with two loops?
0:150:43How to Buckle a Belt With Two Loops : Solutions for Clothing QuestionsYouTubeStart of suggested clipEnd of suggested clipBring the belt back. Pull the first buckle over to the right slide the belt through and bring itMoreBring the belt back. Pull the first buckle over to the right slide the belt through and bring it under the other buckle tighten the belt to the desired tightness Center your buckle and you're all set.
How tight should the tensioner pulley be?
When twisted either way from the middle, the tension in the belt must not be more than 12 inch. The belt is too tight if it is twisted more. The positions do not work for the vehicle.
How do I stop my golf cart belt from squeaking?
Your belt may also be wearing down and even fraying which is a problem that can cause the belt to both squeak and whine as it runs. Replace any frayed belts right away, before they break, to avoid damaging your engine, and lubricate or replace any pulleys which continue to squeak on your cart.
How does a clutch work on a golf cart?
0:463:28How a golf cart CVT slip drive clutch works - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the rear drive clutch actually separates it widens causing the belt to drop down into the clutchMoreAnd the rear drive clutch actually separates it widens causing the belt to drop down into the clutch.
How do you change a drive belt on a Yamaha golf cart?
0:462:46Yamaha Drive Belt | How to Install on G29 Golf Cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow to wet do this on the back clutch or the secondary clutch take the belt and slowly lay it overMoreNow to wet do this on the back clutch or the secondary clutch take the belt and slowly lay it over the top of this outer chief like this just slowly roll it over. And. It will come right.
How to tell if golf cart drive belt is too tight?
To check if your drive belt is set just right make sure your golf cart is turned off then check the drive belt by pressing it down between the two clutches with your finger. If it deflects less than 1.5” it’s too tight.
Why is my Ezgo golf cart belt so loose?
The reason your EZGO drive belt is too loose could be because it’s worn out, or you’re simply using the wrong size drive belt. In this case, need to find a replacement immediately. A loose drive belt can result in your EZGO Golf Cart to lose top speed and underperform.
Why is my EZGO drive belt so tight?
The reason your EZGO drive belt is too tight can be because you’re not using the right size drive belt. Check and make sure if you’re using the right one. A quick search online will give you the right information. It can also be too tight because the drive/driven clutch is misplaced or broken.
Why is my clutch too tight?
It can also be too tight because the drive/driven clutch is misplaced or broken. A drive belt that’s too tight can damage the drive and driven clutches and can also result in the drive belt being worn out too fast. To check, whether the drive/driven clutch is misplaced or broken call a certified technician to have a look.
Why is my drive belt so loose?
If the drive belt is the right model but it seems to be too loose then it could be because there is something stuck in the clutch or there is some damage in the clutch. In this case you’ll need to call a certified technician to inspect your golf cart.
How to stop a EZYGO drive belt from slipping?
How to stop a EZYGO drive belt slipping: Make sure that you have the right drive belt. Sometimes the wrong drive belt will not be as wide as the clutch you are putting it on. This gives it an unwanted room to move back and forth when you are using the golf cart.
Where is the primary drive clutch located?
After doing so, you can follow these steps: Locate the primary drive clutch. It’s located at the bottom of the two clutches and is the smaller one. Take note of how the existing belt has been adjusted to the clutches and then remove it.
How to change the belt on a golf cart?
Slide the old drive belt off the front drive clutch pulley, and then the rear clutch pulley. Slip the new belt around the golf cart's clutch pulley, and then stretch it out over the front pulley. Pull the front pulley forward slightly to increase the belt tension, and then tighten the tension bolt with the wrench.
Why does my golf cart not engage?
If the cart is having trouble accelerating or will not engage at all, it may be because the belt needs changing. Park the golf cart, and turn off the engine.
