How to use a Mikuni carburetor on a golf cart?
Flip the choke lever of the Mikuni carburetor from side to side for about half a minute. The cart makes use of a Walbro carburetor with three-line vacuum pumps with connections as follows. One vacuum pump is connected from the gas tank to the fuel pump. The second vacuum pump is connected from the fuel pump to the carburetor.
What kind of carburetor does a Columbia golf cart have?
1985 Columbia gas golf cart The cart makes use of a Walbro carburetor with three-line vacuum pumps with connections as follows. One vacuum pump is connected from the gas tank to the fuel pump. The second vacuum pump is connected from the fuel pump to the carburetor.
What is the fuel pump pressure on a Yamaha G2 cart?
An electric fuel pump in a Yamaha G2 cart often has a low pressure of 3 to 5PSI with 1/4-inch lines. In some cases, the fuel pump gets activated when the fuel pressure is lower than 2PSI.
How to clean the carburetor of a golf cart with fuel breakdown?
Fuel breakdown due to long-term storage 1 Unhook the gas lines from the golf cart. 2 Drain the fuel inside the fuel pump into an approved gasoline storage container. 3 Empty the contents of the carburetor. You can use this chance to clean the carburetor inlet.
How to remove jets from carburetor?
Each jet can be removed with a flat blade screw driver. To adjust the jet needle position you need to unscrew the top of the carburetor. Be careful as you take the cap off because there is a spring inside. Once you remove the cap and spring you will see the slide inside the carb.
How to setup throttle cable?
To setup your throttle cable, insert the throttle cable into the top of the carburetor cap. The rubber boot on the cap will hold the cable in place. Your cable will need a lead ball or barrel on the end of the cable wire. If your cable does not have a lead ball or barrel on the end you can solder on a cable fitting p/n 16430.
Can you tune a Mikuni carburetor?
There is a large amount of horsepower to be found in a properly tuned carburetor. Unfortunately, there isn't a universal setup that will work with every engine combination. Jetting that works great with one engine may not work so well with another. Armed with an assortment of jets and a free afternoon, we are confident you can tune your Mikuni ...
How to adjust carburetor on golf cart?
In most cases, you’ll need to adjust the jet pilot screw, perform a valve clearance adjustment and then clean the carburetor.
How to replace carburetor float?
Remove the carburetor and turn it upside down. Remove the nut that is used to secure the bowl on. Check the float for a puncture as this prevents the activation of the fuel cut-off needle valve. Replace the float if there is a puncture. Check for dirt accumulation in the needle valve.
Why does an EFI carb require more maintenance than an EFI?
The carb requires more maintenance than an EFI because of the cleaning and rebuilding of the carburetor involved.
Why does my carburetor flood on my golf cart?
The reason why a carburetor floods on a golf cart is usually due to a faulty fuel pump. The pump must be repaired or replaced accordingly. Seek professional assistance if required. This is usually due to the proximity of the fuel line to an exhaust manifold, a radiator hose or a heat source.
How to cool down a golf cart?
Procedure. Turn off the golf cart engine and allow it to cool for a couple of hours before you start working. This cooling down prevents damage to the cart and injury to yourself when you’re at work. Turn off the fuel-supply valve and remove the fuel line to prevent flooding of the fuel and other complications.
Which is more powerful, carb or EFI?
The carb model is more powerful as well as starts and goes faster when compared to the EFI. The EFI experiences delay to start moving when the pedal is pressed.
How to remove cable from carburetor?
Remove the cable from the carburetor and cover its sheath opening using duct tape. To do this, make a small funnel with the tape and ensure that the wire sticks out from its middle. Loosen the nut that fixes the cable on to the mount housed on the motor just before its entry into the carburetor.
How does a Mikuni carburetor work?
A Mikuni carburetor, like any other carburetor, is a mechanical device. It works in motorcycles to combine air and fuel within the internal combustion engine. Its primary job is to control air flow into the engine. During this controlling process, the air pressure within the engine is determined by the speed at which the air enters ...
How to identify a Mikuni carburetor?
How Do You Identify Mikuni Carburetors? It’s simple to identify a Mikuni Carburetor by looking at the top view of the float chamber cover, the cover gasket of the float chamber or the jet chamber cover gasket. The word Mikuni ought to be printed somewhere on the carburetor. It could be in small or large letters.
What is a Mikuni 33mm carburetor?
Like other Mikuni carburetors, the TM Series 33mm improves throttle response on motorcycles. The air flows faster in the TM series and the flat slide design blocks the jet helping to create a smooth bore effect. It is a dual cable carb and works on the Suzuki 97 DR350 bike and others, empowering them to run as though they are new although they may be significantly older.
What carburetor fits a Honda XR?
This carb works with a Honda XR/CRF engine ranging from 100cc, 200cc and 250 cc. if you want to see the horsepower in your pit bike increase, then this is the carburetor of your choice. It also increases the airflow in the bike. The 30mm carburetor fits bikes that have an engine similar to that of the Honda 200 250. Additionally, it works with a 44mm air filter and improves throttle response in general.
What is Mikuni HSR48?
The Mikuni HSR48 is used with race and custom applications and is not for use with standard applications. It is custom polished for the Harley Davidson and uses the Harley’s cables in addition to coming with a Flange. Its finish is that of high polished aluminum and it helps riders and racers to realize the optimum potential of their custom race engines. Additionally, it is recommended for use in engines that are 120ci or bigger. These engines ought to have higher flow heads and cams for the Mikuni carb to be compatible.
Why is a carburetor important?
The carburetor, for example, is one of the most important parts of your bike. It heavily influences the throttle: the response and control that you have as the rider. It has the power to improve throttle control which is desirable to the rider. A time comes when you need to replace your carburetor, adjust it or even rebuild it.
Does Mikuni carburetor work with stock motor?
There are a number of advantages to be enjoyed from using Mikuni carburetors. The first is that it drastically improves throttle response. It does work best with a stock motor. Secondly, it is easier to tune and does not force you to pay extra to get a professional to do it for you as you can do it yourself.
Special offers and product promotions
Create your FREE Amazon Business account to save up to 10% with Business-only prices and free shipping. Register today
Product Description
Please review all product information to ensure that this product is compatible with your unit.
Customer reviews
There was a problem filtering reviews right now. Please try again later.
Top reviews from the United States
There was a problem filtering reviews right now. Please try again later.