The top of the cup holder is snapped on and will come right off. Sometimes you need to use a wide screwdriver or something flat to stick in next to the front 3 tabs to release them. On the key plate those plastic pins will push out of the center and then you can remove the plate.
Full Answer
How do you remove the governor on a golf cart?
1 Loosen the nut attached to the governor arm with a 7/16” wrench to turn the shaft. 2 Push the governor arm to the back of the cart and grasp it with your hand. 3 Turn the governor shaft in the counter-clockwise direction until it cannot be turned further. 4 Retighten the nut and let go off your hold on the governor arm. More items...
How do you bypass the throttle cable on a golf cart?
The throttle cable coming from the gas pedal generates a response to the spring-loaded linkage. This linkage is counteracted by the governor in the golf cart. If you want to bypass the governor, disconnect and reconnect the throttle cable once again without the intervening linkage.
How do you adjust the governor on a Yamaha G2 golf cart?
The following methods show you how to adjust the governor on your Yamaha G2 golf cart. Locate the lever present above the transaxle. This lever houses a 10mm nut. Tighten the nut or move it inwards as much as you want based on the desired speed using a 1/4″ drive ratchet with a 10mm deep socket.
How to replace the gas pedal on a golf cart?
Raise the seat and take off the cushions covering the engine. In newer model carts, you may have to remove the seat screws for raising the seat. Remove the screws present behind the seat on the black plastic cover as well. Locate the thick cable connected to the gas pedal and follow it to trace its connection at the other end.
How do you remove the cup holder on a EZ Go golf cart?
1:107:33E-Z-GO TXT Dash Install.wmv - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's simply pushed back on the stock - pump out with clips. Pull it forward no tools required. YouMoreIt's simply pushed back on the stock - pump out with clips. Pull it forward no tools required. You may need a flathead screwdriver to pry it back if it's a new car or the dash is pretty new.
How do you remove body from a golf cart?
6:569:35EZGO TXT Body Removal | How to Remove Golf Cart Body | Episode 1YouTubeStart of suggested clipEnd of suggested clipI've got all four bolts out of the back what on each sides of bumpers are to pop rivets per side andMoreI've got all four bolts out of the back what on each sides of bumpers are to pop rivets per side and there's two in the bag will they still need to drill. Out.
What is the difference between a G2 and G9 golf cart?
The later G9 model is a virtual clone of the G2 except the G9 has a band of rubber trim around the dash compartment instead of the aluminum trim found on the G2 model. The serial number has a prefix that designates the model, starting with a 'J' followed by 1 more letter and 1 number, or just 2 numbers.
How do you remove the dash on a Yamaha golf cart?
0:337:45Yamaha Drive 2 Golf Cart Body Removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt just has two tabs that hold that down underneath of that is a three millimeter allen head screw.MoreIt just has two tabs that hold that down underneath of that is a three millimeter allen head screw. Then you can just pull up on the dash.
How do I remove a body from my Club Car DS?
2:537:18VLOG #10 Club Car DS body removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipBody is to use a number three phillips on the forward reverse handle remove those bolts and pull theMoreBody is to use a number three phillips on the forward reverse handle remove those bolts and pull the handle. Out. Then the charger receptacle use the number two phillips.
How do you remove lug nuts from a golf cart?
How to remove lug nuts on golf cartOpen the lug nuts with the wrench and hammer while the wheel stays on the ground.After loosening the nuts, use your hand to open the nuts and replace them or tighten them for the performance.
What year is a Yamaha G2 golf cart?
Yamaha Electric & Yamaha Gas Golf Cart Serial Numbers:Yamaha G1 to G11Yamaha's Longest Running Cart Model. The G-Series.JA2-000001G2 GAS1988J55-000101G2 GAS1989J55-100120G2 GAS199084 more rows
What size engine is in a Yamaha G2 golf cart?
At 357cc and 11.4 horsepower, it is Yamaha's most fuel-efficient carburetor engine. The PowerTech AC enables muscular hill climbing and a smooth ride. At 48 volts, its output is 5.0kw (6.7hp) for up to 60 minutes before recharging.
What year did Yamaha drive 2 come out?
2017In 2017 Yamaha introduced the current model, the Drive2.
How can I make my Yamaha Golf Cart faster?
0:005:15Yamaha G29 Drive Golf Cart Governor Adjustment - MORE SPEED!!YouTubeStart of suggested clipEnd of suggested clipItself by tightening this nut down you're putting more pressure on the spring. So that the governorMoreItself by tightening this nut down you're putting more pressure on the spring. So that the governor has to work harder to pull back on the throttle.
How do I speed up my Yamaha electric golf cart?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
How do you take the governor off a Yamaha gas golf cart?
General InstructionsDetach the cable from the carburetor. The cable is about the width of a straw. ... Follow the disconnected cable up to the governor. ... Disconnect the gas pedal cable from the governor and reroute it to the carburetor. ... Using your wrench, remove the bolt on the gas pedal shaft.
How to adjust golf cart governor?
The governor on a golf cart can be adjusted easily by loosening the tension on its springs using a wrench or screwdriver to get the golf cart going at a relatively faster speed.
Where is the governor arm on a golf cart?
Locate the governor arm of the golf cart. This is mounted above the rear axle housing and under the cart. Depending on the cart model, there may be a protection plate above the governor.
How Does a Golf Cart Governor Work?
A golf cart governor is a mechanical device that helps in controlling the maximum speed of the cart when it moves on flat ground. This device prevents the engine RPMs from increasing beyond the recommended specifications.
How to increase the speed of a cart?
Loosen the nut fitted on the cable. This will gradually increase the length of the cable. As the length increases, the speed of the cart will increase accordingly.
How to start a golf cart with a gas pedal?
Locate the gas pedal that is fitted to the governor and remove the connection. Re-route the gas pedal to the carburetor. Remove the bolt present on the shaft of the gas pedal. Slide the shaft upwards so that the gas pedal has more play. Tighten the bolt and start the golf cart.
How fast is an EZGO golf cart?
The top speed of an EZGO golf cart is usually 19.9mph and the average speed is 14mph to 15mph. With governor adjustment, the EZGO cart can go faster by 5 to 10mph.
How to change the speed of a golf cart?
Locate the spring on the differential or carburetor that helps in changing the cart speed by adjusting its tension. Increase the length of the cable that is fitted on to the body of the throttle and clutch of the two-stroke engine.
