Apply heat evenly to the hosel for about a minute, using a heat gun or heat torch. This will break down the epoxy that bonds the shaft to the hosel and make removal easier. If you are working with graphite shafts, use a heat gun, not a torch.
Full Answer
How do you remove a golf shaft from the head?
Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly. Remove the ferrule. The ferrule is the small plastic band that sits just above the hosel.
Do you need a professional to reshaft a golf shaft?
It is sometimes necessary to have a professional tackle a complete reshaft job; however, it can make his job easier if you eliminate a step in the process. Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly. Remove the ferrule.
Can You Heat a club in a shaft puller?
However, if you do heat the club with it in the shaft puller, make sure to heat the rear of the hosel. If you do discolor the head, at least it will be on the back side that it least likely to be seen by the golfer when the club is at address.
How do you heat the hosel on a golf club?
Heat the hosel (small metal joint linking the shaft to the club head) with a heating gun. Be sure to dispense heat evenly on all sides of the hosel and don't be alarmed if small amounts of white smoke begin to escape the hosel cavity.
How do you remove a shaft from a golf club?
1:015:14Golf Club Repair - Part 1 - Removing a shaft & cleaning the hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro willMoreBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro will come right off you can almost pull it off with your hands once it gets softened.
How do you remove a golf shaft at home?
0:172:32How To Remove A Steel Golf Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also use a heat gun but it's going to take three times as long. The other things that you'reMoreYou can also use a heat gun but it's going to take three times as long. The other things that you're going to need or a club making vice vice clamp some heavy-duty gloves and probably a knife.
Can you remove a golf shaft with a hair dryer?
Another alternative heat source I've had success with (literally twice) was a hair dryer. I read about golfers packing prized putters in their carry-on luggage, re-shafting at their hotel, and then removing the head with the hotel hair dryer prior to traveling home. Following that, I tried it and it worked.
How do you remove the shaft from an iron?
0:437:18Removing an iron shaft by hand - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you guys have a set of clubs that are out there steel shafted irons and you're just kind ofMoreSo if you guys have a set of clubs that are out there steel shafted irons and you're just kind of interested in tinking around how do i take them apart.
Can I Reshaft my own golf clubs?
Reshafting is just one way to keep your clubs performing at a high level. You can also benefit from regripping your clubs. Replacing worn-out golf grips can help make your clubs feel new again. Adding the right shaft to your favorite clubs can get you back on the course and working toward a new personal low round.
How do you remove a graphite shaft at home?
0:184:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're just going to damage the shaft. So you needed a special tool called a graphite shaft pullerMoreYou're just going to damage the shaft. So you needed a special tool called a graphite shaft puller you're several on the market.
What temperature does golf epoxy melt?
You must apply enough heat to break the epoxy bond. Shaft epoxy breaks down at about 250 degrees Farenheit.
How do you Reshaft a driver at home?
0:144:53How To Reshaft Golf Clubs - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere just as the pocketable bandha looks better with it as you can see two of ours also prep the tipMoreHere just as the pocketable bandha looks better with it as you can see two of ours also prep the tip taken basically the paint off the shaft that way to here to the epoxy.
How do you remove graphite shaft without a puller?
0:556:40pulling a graphite shaft 2016 - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow can you use a propane torch and the big monster. Yeah you can particularly if you're using steelMoreNow can you use a propane torch and the big monster. Yeah you can particularly if you're using steel on steel I don't see anything wrong with it it's just a much bigger. Application of the heat.
Can you reuse a golf shaft?
However, if the shaft tip stays intact, take a closer inspection of the tip section to see if you notice any longitudinal cracks or delaminating, or basically anything that you think would be considered damage. If not, there is a good chance you could reuse the shaft into another head or the same head later on.
How do you change a golf club shaft?
0:5210:45How to replace a golf club shaft - Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is a nylon brush a wire brush wouldn't be too bad either that way you can clean out the actualMoreThis is a nylon brush a wire brush wouldn't be too bad either that way you can clean out the actual end of the golf club or the iron. Before you actually put the new shaft in you'll need a ferrule.
How much does it cost to Reshaft a golf club?
The average cost to reshaft your golf clubs is $24 per club plus the cost of the shaft and grip. A new iron shaft and grip can range between $10 and $95 while a new driver shaft and grip can range between $18 and $440. The majority of the cost comes down to what type of shaft you want and what grips you like.
How to remove graphite shaft?
One method to remove a graphite shaft is to remove the ferrule, cut the shaft off at the hosel and drill the remaining part out of the hosel. However, on modern drivers, fairways and hybrids which are nearly all hollow inside, could potentially could push material into the cavity of the head and cause it to rattle.
When to remove head from shaft?
You are now ready to apply heat to the head for the purpose of removing the head from the shaft. It is best to remove the shaft as soon as the epoxy breaks loose. By doing so, this will limit the possibility of heat penetrating into the shaft and causing it to break down.
What is a graphite shaft made of?
A graphite shaft is made from many layers of graphite pre-preg or long continuous strands of carbon fiber wrapped around a forming mandrel. To hold the layers or strands together, an epoxy resin is used. This same epoxy resin is not much different from the epoxy that is used to hold the head onto the shaft. In order to remove the head ...
How long to reheat a golf club?
If the clubhead does not come off at this point, reheat for a period of 25-30 seconds. Remember, you can always reheat the hosel, but you can’t remove heat if you heat the club too long. Continue this method of heating for 25 second intervals until the shaft puller has forced the clubhead from the shaft.
How much does a shaft puller cost?
Shaft pullers can range anywhere from around $20 for a devise that looks like a modified pry bar (you still need a vise and shaft clamp) to several hundred dollars for a hydraulic model. Regardless, invest in a good shaft puller if you are repairing clubs in any sort of volume. Remember how much shafts cost again.
How many times can you remove graphite from a clubhead?
Sometimes these steps will have to be repeated as many as 3 or 4 times (or more) before successfully removing the graphite shaft from the clubhead, especially for titanium and aluminum clubheads. The more pressure that the shaft puller applies the less heat it takes to remove the shaft from the clubhead.
What to do before you heat a propane tank?
Rule #4 – Before you heat, take a peek. Before grabbing the propane tank, take of peek of the finish because this will tell you what type of heat source to use. If the hosel is a satin or high polish finish, you should have no problem using a propane (or butane) torch or heat gun.
How to get the head off a golf club?
Place the grip end of the club on the ground so the head end is sticking straight up and gently pull the head off the shaft. Do not twist, especially if you want to reuse the shaft or sell it, as twisting may harm the inner walls of the hosel as well as the tip of the shaft.
How to heat a hosel?
Heat the hosel (small metal joint linking the shaft to the club head) with a heating gun. Be sure to dispense heat evenly on all sides of the hosel and don't be alarmed if small amounts of white smoke begin to escape the hosel cavity. That is just the old epoxy melting.
Is a stock shaft good for golf?
Golf shafts come in a variety of materials, flexes and specifications. Often, the stock shaft is not the best choice for your particular game. You may remove the original shaft and replace it with one that more closely fits your abilities. When considering a new shaft, note features such as weight, length, kick point and flex.
Can you remove graphite shafts?
It is important to know the proper technique for removing a graphite shaft. A graphite shaft could be ruined forever if removed by the conventional twist and pull method that we use for steel shafts. The fibers in the shaft tear apart when you do this.
Can you load a spring in a vise?
If you buy a spring that is larger on the inside than a shaft, you can load it in the vise to make the hosel protector apply continuous pressure to the club head.
Series Navigation
In this video, I show you how to remove the putter head from the shaft. I use a propane torch, but a heat gun would suffice too. This technique can be used for irons, wedges, etc.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
