Apply heat evenly to the hosel for about a minute, using a heat gun or heat torch. This will break down the epoxy that bonds the shaft to the hosel and make removal easier. If you are working with graphite shafts, use a heat gun, not a torch.
How to remove a head from a golf shaft?
However, if you do heat the club with it in the shaft puller, make sure to heat the rear of the hosel. If you do discolor the head, at least it will be on the back side that it least likely to be seen by the golfer when the club is at address. You are now ready to apply heat to the head for the purpose of removing the head from the shaft.
How do you remove a ferrule from a golf club?
Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it. Place the club in a vise to position it for shaft removal. The club should lie horizontally. Make sure the vise grips the shaft securely to prevent it from slipping out. Expose the length of the head and about 8 inches of shaft. Heat the glue inside the hosel.
How do you remove epoxy from a golf club head?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.
How do you fix a broken shaft on a golf club?
Expose the length of the head and about 8 inches of shaft. Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. Light your propane torch and apply heat to the underside of the hosel.
How do you remove a shaft from a golf club?
0:194:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you needed a special tool called a graphite shaft puller you're several on the market. That areMoreSo you needed a special tool called a graphite shaft puller you're several on the market. That are commercially available but they do essentially the same thing they securely clamp the shaft.
Can you remove a golf shaft with a hair dryer?
Another alternative heat source I've had success with (literally twice) was a hair dryer. I read about golfers packing prized putters in their carry-on luggage, re-shafting at their hotel, and then removing the head with the hotel hair dryer prior to traveling home. Following that, I tried it and it worked.
How do you remove a golf shaft at home?
0:172:32How To Remove A Steel Golf Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also use a heat gun but it's going to take three times as long. The other things that you'reMoreYou can also use a heat gun but it's going to take three times as long. The other things that you're going to need or a club making vice vice clamp some heavy-duty gloves and probably a knife.
How do you remove a golf driver head shaft?
As you apply heat, grab the clubhead and gently turn it to begin working it out. Avoid cranking with too much force. The shaft could break off inside the hosel. Work the head free carefully and gradually until it comes off.
What temperature does golf epoxy melt?
You must apply enough heat to break the epoxy bond. Shaft epoxy breaks down at about 250 degrees Farenheit.
How do you remove graphite shaft without a puller?
0:193:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain using a butane torch you can actually really focus the heat which is a lot better than sayMoreAgain using a butane torch you can actually really focus the heat which is a lot better than say trying to use a heat gun which could end up damaging. The fibers of the golf shaft.
Can you put a new driver head on an old shaft?
The only way to know if we can put your old fitted shaft into a new head it to pull the shaft, weight the head and test the new head with the old shaft. The head may be heavier or lighter, the hosel dimensions may be off which could cause a length issue.
Can I Reshaft my own golf clubs?
The average cost to reshaft your golf clubs is $24 per club plus the cost of the shaft and grip. A new iron shaft and grip can range between $10 and $95 while a new driver shaft and grip can range between $18 and $440. The majority of the cost comes down to what type of shaft you want and what grips you like.
Should I take my driver head off when flying?
Remove the Heads Removing the club heads decreases the likelihood of the heads getting snapped off in transit, one of the easiest ways of mastering how to protect your golf clubs when flying. Simply wrap the club head in a golf towel or a headcover and store it in an extra pocket of your golf bag.
What kind of epoxy is used for golf clubs?
Permabond offers a range of toughened epoxy adhesives which are suitable for bonding golf clubs. They offer excellent adhesion to carbon, graphite, composite, titanium, steel, wood and many other materials. Cure speed and viscosity can be matched as per the user's preference.
Are graphite shafts good?
Benefits of Graphite Shafts Graphite shafts are lighter than steel shafts, resulting in an increase in swing speed and distance. This is particularly beneficial to players with slow swing tempos. Most golfers can realize an increase of at least 5 yards for each club.
How do you make a golf grip solvent?
Water and Soap The cheapest and most convenient homemade solvent is water. Water-based grip tape has a glue-like substance that is activated by water. Before you spray the tape, add a small amount of detergent, which provides lubrication.
How do you remove iron head shaft?
2:447:18Removing an iron shaft by hand - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn order to be able to apply the knife. And pull it down. All right now the reason why i'm tellingMoreIn order to be able to apply the knife. And pull it down. All right now the reason why i'm telling you this is i tried doing it without moving the ferrule.
How do I remove a shaft adapter?
0:139:32How to Remove Golf Shaft Adapter - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you start to see it's a bubble up a little bit just take your hook blade. Slide it right underMoreOnce you start to see it's a bubble up a little bit just take your hook blade. Slide it right under there. And it should come off free easy a little cold out here in the shop tonight.
How do I change a golf club shaft?
1:465:54Golf Equipment : How to Change a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp as that shaft heats the epoxy starts to break down. And then the shaft the head of the club willMoreUp as that shaft heats the epoxy starts to break down. And then the shaft the head of the club will come will pull off of that shaft. Once that epoxy gives way then you can turn your heat gun.
How do you pull a fairway wood shaft?
1:054:56Club Building 101: Pulling a Shaft from a Bonded Driver - YouTubeYouTubeStart of suggested clipEnd of suggested clipGet it set up. And you'll see that it's already starting to push the ferrule. That's fine startingMoreGet it set up. And you'll see that it's already starting to push the ferrule. That's fine starting to really mush. It.
How to get epoxy off of a clubhead?
Apply pressure to the clubhead, while applying heat to the hosel at the same time. Continue doing this until the epoxy bond has softened and the clubhead comes off easily.
How to make a golf club with masking tape?
Step 1. Completely cover the head of the club with masking tape to prevent the head from being scratched during the process. Now, place the club in the vise, so that the middle of the shaft is the part being held in the vise. Make sure the club is held securely.
How to get ferrule off of a car?
Take the utility knife and cut off the small plastic piece at the base of the shaft , also called the "ferrule." If the ferrule doesn't come off easily, use the butane torch to heat it a bit, and then it should come right off.
Can you replace a golf club shaft instead of replacing the entire club?
By Tami Fisher. Replacing a golf shaft instead of replacing the entire club can save money. Once in a while, something happens to cause a golf club shaft to splinter or even break. When this happens, the old shaft must be removed and a new one installed in its place.
What to do if your golf club shaft is bent?
If the shaft of your golf club is bent or broken, do not discard the entire club. Instead, remove the clubhead from the damaged shaft and install it on a new one. Disconnecting the golf club shaft from the head also allows you to try the latest shaft technology on the market without purchasing a whole new club.
How to remove ferrule from golf club?
Step 1. Use a utility knife to scrape off the ferrule at the connection point between the shaft and the clubhead. Scrape down toward the head and away from your body.
How to catch a club head off a golf club?
Press down on the hosel with a pry bar. Do not twist the head off, as this can damage the shaft. As you press on the hosel, have your other hand ready to catch the clubhead when it drops off the shaft.
How to twist a golf club head?
Remove heat from the hosel and twist the club head counterclockwise. It should twist off fairly easily. If it does not, apply more heat.
How to remove graphite from hosel?
Apply heat evenly to the hosel for about a minute, using a heat gun or heat torch. This will break down the epoxy that bonds the shaft to the hosel and make removal easier. If you are working with graphite shafts, use a heat gun, not a torch. Wear goggles and protective gloves.
Do you need a new shaft for golf?
Almost every golfer will need a new shaft at some point during his golfing career. Clubs can be reshafted at most golf stores and country clubs, but if you are a do-it-yourself type, removing and/or installing a new shaft is a straightforward project that will save you money.
How long to reheat a golf club?
If the clubhead does not come off at this point, reheat for a period of 25-30 seconds. Remember, you can always reheat the hosel, but you can’t remove heat if you heat the club too long. Continue this method of heating for 25 second intervals until the shaft puller has forced the clubhead from the shaft.
How to remove graphite shaft?
One method to remove a graphite shaft is to remove the ferrule, cut the shaft off at the hosel and drill the remaining part out of the hosel. However, on modern drivers, fairways and hybrids which are nearly all hollow inside, could potentially could push material into the cavity of the head and cause it to rattle.
How many times can you remove graphite from a clubhead?
Sometimes these steps will have to be repeated as many as 3 or 4 times (or more) before successfully removing the graphite shaft from the clubhead, especially for titanium and aluminum clubheads. The more pressure that the shaft puller applies the less heat it takes to remove the shaft from the clubhead.
What to do before you heat a propane tank?
Rule #4 – Before you heat, take a peek. Before grabbing the propane tank, take of peek of the finish because this will tell you what type of heat source to use. If the hosel is a satin or high polish finish, you should have no problem using a propane (or butane) torch or heat gun.
How to protect a carbon head?
If this is the case, go to you local welding supply center and get a bottle of a product called Cool Gel. This is very cool stuff! Just spray it on the carbon surface only and it will protect it from any wayward heat like an accidental pass with the torch. When you are done, you can just wipe the head with a wet paper towel or rag to remove the gel.
When to remove head from shaft?
You are now ready to apply heat to the head for the purpose of removing the head from the shaft. It is best to remove the shaft as soon as the epoxy breaks loose. By doing so, this will limit the possibility of heat penetrating into the shaft and causing it to break down.
Does stainless steel hosel heat up?
If you heat a stainless steel hosel, it remains hot in the area that it is heated. Where as titanium and aluminum are very good conductors of heat and the heat will transfer to the other parts of the head. Thus it takes a longer duration of heat to break the epoxy bond loose.
How to install a new shaft on a golf club?
Prepare the hosel of the club head for your new shaft by removing the old epoxy from inside it. The easiest way is to first put the club head into a vise , making sure you don't damage it. Then use a hand drill to carefully remove the debris. Make sure that the hosel is totally clean before you begin installing your new shaft.
How to loosen epoxy on golf club shaft?
Move the plastic ferrule from its position next to the club head to a position up the shaft so that it will be out of the way and won't be damaged when you apply heat. Step 3. Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. ...
How to remove epoxy from golf club?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside. Since the club head can get quite hot, wear ...
