How to Lengthen a Driver Shaft
- Get an extension with a butt diameter of a slightly lower size than that of your present shaft so that it goes into the current shaft with a tight fit.
- Place a little two-component golf epoxy on a clean surface and mix it up.
- Use a toothpick or a small spatula and apply some epoxy on the outer surface of the extension.
Full Answer
How to measure golf shaft length?
How to measure golf club shaft length 1st step. Place the golf club on a level surface with your toes. Fix golf club point perfectly. 2nd step. Place a border above the golf club that you will use to fix a specific place. For example, fix the 60-degree angle to the head of the golf club. 3rd step
How to extend a golf shaft?
Materials Needed
- Extension (You could also use an old golf shaft) Make sure you purchase the right size extension. ...
- Brampton Pro-Fix 20/20 Epoxy
- Paper Towels
- Acetone
- Epoxy Board (or something smooth to mix epoxy on)
- Something to mix epoxy with (I use the end of a paintbrush)
What is the best golf shaft for a driver?
Shaft Material
- Steel. Steel is the most frequently used material in iron shafts. ...
- Stepped Steel Shaft. The shaft reduces in diameter from top to bottom via some steps at intervals. ...
- Rifle Steel Shafts. Rifle steel shafts are manufactured using a similar process to stepped shafts but without the reduction in diameter and any steps.
- Graphite Shafts. ...
- NanoFuse Shafts. ...
How much does re-shafting golf clubs cost?
The cost of re-shafting a golf club will depend on the number of clubs, the type of materials, as well as the professional that is doing the job. How much does reshafting golf clubs cost? Depending on the quality of the shaft, the cost can be anywhere from $15 to as much as $150 per club .
Can you add length to a golf shaft?
There are two ways to lengthen your shafts. You may add extenders to your existing shafts or you may replace your existing shafts with longer ones. The effects can be very different. Tom Wishon has written extensively about the effects of changing shafts in "The Golfsmith Practical Clubfitting Program" guide.
How can I make my golf shaft longer?
1:1014:42Golf Club Repair - How To Extend a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe are going to talk about the graphite first then the steel rule of thumb in the McGowan. LikeMoreWe are going to talk about the graphite first then the steel rule of thumb in the McGowan. Like material for like extension meaning that you have a like that's a graphite extender.
How much does it cost to extend the shaft of a golf club?
Everything will be explained in this article. Most retailers will charge $15-$25 to install a shaft, once a club is re-shafted it needs a new grip which ranges from $3-$12, the average cost to replace a golf shaft is $18-$37 per club. Clubs are either graphite or steel, reshafting a graphite club is far more expensive.
At what height should you lengthen golf clubs?
Using the ratio of every 6" of height there should be a 1" change in length then there should be a 1 ½" difference between their 5-irons. For example, recommend 36.5" for the lady and 38" for the man (or 36.75" / 38.25").
What if my golf clubs are too short?
What Happens When Golf Clubs Are Too Short? For most golfers, having clubs that are too short will be better than if they're too long, but can still result in inconsistent shots. Clubs that are too short will make you stand bent over, which can cause back pain. You'll also have the tendency to push the ball a lot.
Should I add length to my irons?
Sometimes a golfer's height and arm length will negate each other and a standard length is the best option. As length is increased, so is the weight. Increasing the length also changes shaft flex. For every 1" added, the shaft becomes one flex softer; likewise, a shorter shaft plays stiffer.
Is it worth it to Reshaft irons?
Reshafting is just one way to keep your clubs performing at a high level. You can also benefit from regripping your clubs. Replacing worn-out golf grips can help make your clubs feel new again. Adding the right shaft to your favorite clubs can get you back on the course and working toward a new personal low round.
Can you add length to a graphite shaft?
Never extend a graphite shaft more than 2″. Any more may cause premature failure due to stress where the extension is made. 2. Always use either nylon or plastic extensions to extend a graphite shaft.
Does half an inch make a difference in golf clubs?
Master clubmaker Ralph Maltby says that adding 1/2 inch length can add about 5 to 7 yards in distance for irons. But the longer shaft still makes it harder to control the clubhead, which is even more important the closer you get to the green.
How long should my driver shaft be for my height?
Driver Shaft Length Based Solely on HeightHeight (feet/inches)Driver Shaft Length5'4″-5'7″45.5″5'2″-5'4″45″5'0″-5'2″44.5″4'10”-5'0″44″6 more rows•May 9, 2021
How long should your golf clubs be if you are 5 7?
2. Get Your Wrist-to-Floor Measurement (once more, “static” fitting)OVERALL HEIGHTWRIST-TO-FLOOR MEASUREMENTGOLF CLUB LENGTH ADJUSTMENTS5'4″ to 5'7″32 to 34 inchesminus 1/4″5'7″ to 6'1″34 to 37 inchesstandard length in inches6'1″ to 6'2″37 to 38.5 inchesplus 1/4″6'2″ to 6'4″38.5 to 40 inchesplus 1/2″7 more rows
What height is Tiger Woods?
6′ 1″Tiger Woods / Height
How does lengthening a shaft affect swing?
Timing and Feel. In many ways, the biggest effect of lengthening a club shaft is how it affects your ability to swing the club. The combined changes in length and swing weight make the club feel different. In turn, these changes will affect your timing and even your mechanics, perhaps without you even realizing it.
What does swing weight mean?
Swing Weight. Swing weight isn't an actual weight so much as a comparison of the difference in weight between the club head and the butt end of the shaft. It's expressed as a letter-number combination, such as C9 or D2. Lengthening the shaft increases the swing weight, which makes the club head feel heavier. It may even make the club too heavy ...
Can you add extenders to your golf shaft?
You may add extenders to your existing shafts or you may replace your existing shafts with longer ones. The effects can be very different. Tom Wishon has written extensively about the effects of changing shafts in "The Golfsmith Practical Clubfitting Program" guide.
Does lengthening the shaft make the club head heavier?
Lengthening the shaft increases the swing weight, which makes the club head feel heavier. It may even make the club too heavy for you, which will slow down your swing speed and actually reduce your distance.
Does lengthening a golf club shaft affect accuracy?
Accuracy. As a general rule, lengthening any club's shaft will reduce your accuracy with that club. The longer the club, the more difficult it becomes to hit the ball solidly. This is especially true when the ball is on the ground rather than on a tee, since hitting the ball fat is more likely.
Is shaft length a factor?
Shaft length is certainly a factor in how far you hit a given club. However, some clubs benefit more than others. Installing longer shafts in wedges and short irons will almost always result in more distance, as most players have little trouble swinging the shorter clubs.
Do golf clubs have longer shafts?
Effects of Lengthening a Golf Club Shaft. Tall players like Bubba Watson have to use longer shafts in all of their clubs. Most players consider using longer shafts in their clubs at some time or another, believing that longer shafts equal more distance, although that isn't necessarily true. There are two ways to lengthen your shafts.
Why Do I Need To Extend My Golf Shafts?
One thing that is obvious when playing golf is that if you don’t play with clubs that offer a good fit, your performance will be affected.
How To Install Golf Shaft Extenders
To start, you will need to remove the old grip and you can do this using a utility knife.
Conclusion
If your golf clubs are too short then you may have considered investing in a new set but there really is no need.
How long is a golf driver shaft?
The standard length for a male driver shaft used to be 43.5 inches for a steel shaft and 44 inches for a graphite club. However, in recent times, the standard driver length has been accepted as 45 inches. Typically, the length of a female golfer’s club is an inch lesser than that of a male golfer’s club.
How to shorten a golf club shaft?
Remove the grip from the driver using a hook blade or a utility knife, as well as the grip tape on the shaft. Measure the length that you want to shorten on the shaft. Add an extra 1/8 inch to this and mark the position using a permanent marker. Fix the golf club in position in a vise.
Why is grip size important?
Grip size is just as important as the size of the shafts of your driver and other golf clubs for a perfect game. Big grip size can inhibit your wrist release through the impact area and cause a fade or a block.
How to make a golf club more upright?
By increasing or decreasing the shaft length by an extra half an inch will result in the club playing 1 degree more upright, or flat respectively. With a standard-length club, tall players tend to stoop quite a bit while short players will find themselves having to stand in a more upright position than required.
How to narrow down a golf shaft?
The best way to narrow down on the right shaft is to do test shots on the range with drivers of varying lengths. The right shaft length will help you to hit the golf ball with the driver much the same way that you would do with a wedge.
What is the difference between the length of the golf club and the length of the clubhead?
The length of the golf club’s shaft in relation to the overall length of the club defines the length of the driver shaft. Alternatively, this is the difference between the length of the overall golf club and the length of the clubhead. Generally, the longer your driver shaft is, the more difficult it becomes to have control over ...
When you shorten your golf shaft, do you keep in mind the after effects?
When you have decided to shorten your golf shaft, you must keep in mind the after-effects of doing so. How much and where you cut off the shaft has different effects on the golf club.
How does a lengthened golf club work?
A longer distance can be achieved with a lengthened club if you have the ability to swing it with the same force and speed that you did with a shorter club . This increases the ball’s velocity upon impact, and you can hit it farther. Flex: The flex of the shaft will be altered. This happens for a few reasons.
When shortening a golf club, do you have to remove the crown?
When you shorten a golf club, you have to remove the crown, and safely disconnect the shaft from the head.
Why are golf clubs made the way they are?
The reason clubs are made the way they are is to gather momentum as you swing down. If your club is too short, you’re going to build momentum while having resistance, meaning you will push too hard against the wind and not just swing naturally. There’s not enough weight to the club.
What happens if your woods aren't longer?
If your woods didn’t have the length that they do, and they were shorter, you’d be sending your ball almost straight up and they wouldn’t close much of a distance. It’s not always about the angling of the golf club head; sometimes it’s about the length and force to make it meet the ball.
Why do you have to swoop on your golf club?
Because the club is longer, you have to swoop on your downward swing, causing the force of your wood – if you’ve hit it correctly – to be applied to the bottom of the ball and send it upwards. A wood without enough length just doesn’t cut it. You’d be sending the ball higher but with almost no distance.
What happens if you play too long in a golf club?
If the club is too long for you, then you’re spending extra time during ramp up which is the amount of time spent during your initial downswing. You want a balance between your abilities, ramp up, and momentum while cutting through the wind with as little resistance as possible.
Why did Lars start golfing?
Father of six and long-time golfer, Lars started golfing because of a summer job when he was nineteen, where he caddied for a Virginia state official. From that moment on, he fell in love with the sport, and made it a core staple in his life. Thirty-five years later, with thousands of games under his belt, he’s here to teach you the fundamentals and master techniques of golf, while recommending proper golfing gear and equipment for every step in your journey.
How to determine the length of a golf club?
To determine the approximate length of clubs that are right for your height, you need to know how tall you are and how far your wrists hang from the floor. As Golf Components explains, you can obtain your wrist-to-floor measurement by standing on a hard, level surface in regular shoes or golf shoes. Relax your shoulders and let your arms hang down.
What happens if your golf clubs are too short?
In fact, if your clubs are too short or too long, expect to spend lots of time in the rough, bunkers and water hazards, if not out-of-bounds. As club equipment guru Tom Wishon explains, the length, loft, lie of your clubs are critical factors in determining how far and high your shots will fly.
How long is a 5 iron?
Clubs other than drivers gradually get shorter -- if a 44-inch steel shaft driver is indicated by the chart, your 5-iron will measure 38 inches and sand wedge 35.5 inches. Graphite clubs are slightly longer, with a standard driver at 45 inches, 5-iron at 38.5 inches and a sand wedge 36 inches. Standard club lengths for women are one inch shorter ...
What Is Shaft Length?
Shaft length is the shaft’s raw length, which is connected between the clubhead and the grip. It acts like a lever and allows a player to hit the golf ball over a great distance by using the body’s rotation.
Shaft Length in Irons
The optimal shaft length in Irons can be determined by a set of measurements like arm length, player’s height, and swing posture. A tall player would not benefit by using a golf club designed for a short golfer.
Shaft Length in Drivers
The shaft length in drivers helps you determine how fast you can swing the golf club, along with the angle of attack and the club’s path. The standard length for the drivers is 44.5 inches.
How does a half inch length change affect a golf swing?
Every half-inch length change alters the lie by a degree. There will be an alteration in the way you grip the club, change in your positioning or posture while taking a swing, you may need to bend it a little to drop your hands a bit, or you may stand more upright to make up for the change in distance. Since there will be changes in the length of ...
Where is the extension on a golf club?
An extension can be used in lengthening the golf club where it is fitted in the butt end of the shaft , and once dried, the golf club can be cut to the preferred length.
What does it mean when a golf club is too upright?
A club that is too upright every time you swing means that the heel of the clubhead is lower than that of the toe. The tendency here is for the ball to hook, especially for those who are right-handed golfer where the curving of the shot, often takes place. An upright lie angle is more common because the golfers who are just beginning in ...
Why does my golf club slice?
There is a risk of slicing the ball when your angle is too flat. This means that the angle between the shaft and the ground is smaller. Once your club is too flat for your swing, the toe of your golf club will have a lower range than the heel when it should be leveled. Slicing happens because of such reasons.
How to increase swing weight?
Swingweight can easily be increased by using lead tape placed at the clubhead. Lengthening a club softens the shaft a fraction while increasing the swing weight of the club. Each time you add length like half an inch will also add three swing weight points.
What is the best way to get accurate golf clubs?
Club fitting is the best way to get accurate golf clubs, cause there is no standard lie angle that you can find in any golf store, and you need the fitting, so it will be according to your build, swing type, and preference.
How to get the right lie in golf?
To get the right lie, make sure that whenever you change the length of the golf club, you are also trying out the clubs to match your swing. Pro-golf shops can adjust some clubs to match it according to your need.
