Expect to pay anywhere between $40-$100 reshafting a graphite shaft, if the shaft is steel expect to pay anywhere between $20-$75 per shaft, every replacement shaft needs a new grip which costs $8-$15, and labor costs $5-$35 depending on where you live.
Full Answer
How much does it cost to replace a golf shaft?
Most retailers will charge $15-$25 to install a shaft, once a club is re-shafted it needs a new grip which ranges from $3-$12, the average cost to replace a golf shaft is $18-$37 per club. Clubs are either graphite or steel, reshafting a graphite club is far more expensive.
How to replace a graphite shaft on a golf club?
How to Replace a Graphite Shaft on a Golf Club. 1 Step 1. Remove your old graphite shaft. There are two ways to do this step. One way to loosen the shaft from the clubhead is to heat the hosel, or ... 2 Step 2. 3 Step 3. 4 Step 4.
How do you cut a graphite shaft?
Cut the shaft and add your new grip. Allow about 24 hours for the epoxy to completely set before you finish your golf club. Decide on the length of the club, then mark it where the cut should be made. Since the graphite shaft might shatter when cut, put on a few layers of tape on the cut line before you use a band saw to cut it.
How to remove a head from a golf shaft?
However, if you do heat the club with it in the shaft puller, make sure to heat the rear of the hosel. If you do discolor the head, at least it will be on the back side that it least likely to be seen by the golfer when the club is at address. You are now ready to apply heat to the head for the purpose of removing the head from the shaft.
How much does it cost to replace graphite shafts?
If you need a new graphite shaft in your iron, you could be looking at spending anywhere from $40-$100 just for the shaft. Steel, on the other hand, is much more affordable. Depending on the type of steel shaft and the specifications, you are looking at something closer to $20-$75 per shaft.
How do you remove a graphite golf club shaft?
0:384:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you needed a special tool called a graphite shaft puller you're several on the market. That areMoreSo you needed a special tool called a graphite shaft puller you're several on the market. That are commercially available but they do essentially the same thing they securely clamp the shaft.
How much does it cost to change golf shafts?
The average cost to reshaft your golf clubs is $24 per club plus the cost of the shaft and grip. A new iron shaft and grip can range between $10 and $95 while a new driver shaft and grip can range between $18 and $440. The majority of the cost comes down to what type of shaft you want and what grips you like.
How do you remove a graphite iron shaft?
0:353:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain using a butane torch you can actually really focus the heat which is a lot better than sayMoreAgain using a butane torch you can actually really focus the heat which is a lot better than say trying to use a heat gun which could end up damaging. The fibers of the golf shaft.
Can you pull a graphite shaft without a shaft puller?
Well, the general process for pulling a graphite shaft is just about the same, but there are a few key differences. You need to take more care and HAVE to use a shaft puller. Otherwise, your new fancy and expensive exotic shaft could be at serious risk for major damage.
How do you replace a graphite shaft?
4:297:38How to Install Graphite Golf Shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe epoxy. It is recommended that the golf works high-impact epoxy tore set plus epoxy or tore setMoreThe epoxy. It is recommended that the golf works high-impact epoxy tore set plus epoxy or tore set epoxy be used. It is recommended that enough epoxy be used to adequately assemble two clubs.
Do graphite shafts increase distance?
Graphite shafts are lighter than steel shafts, resulting in an increase in swing speed and distance. This is particularly beneficial to players with slow swing tempos.
Are steel or graphite shafts better?
Typically, steel shafts are much heavier, more durable and are generally less expensive than their graphite counterparts. They are more often than not made from stainless steel and they tend to weigh in between around 90g-120g. Torque or lateral twisting found in all graphite shafts is lower in steel irons.
Is it worth Reshafting my irons?
Reshafting is just one way to keep your clubs performing at a high level. You can also benefit from regripping your clubs. Replacing worn-out golf grips can help make your clubs feel new again. Adding the right shaft to your favorite clubs can get you back on the course and working toward a new personal low round.
Can graphite golf shafts be reused?
Reusing graphite iron and wedge shafts. Along the lines of what fupresti said, as long as they're pulled properly you should be able to reuse a graphite shaft indefinitely.
How do you remove a broken graphite shaft from driver head?
1:357:16Removing a Broken Graphite Shaft 2019 -Golf Club Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd this kind of shaft extraction is no different alright so the easiest way that I have found isMoreAnd this kind of shaft extraction is no different alright so the easiest way that I have found is you have to heat up this area and then you step drill.
How do you make a golf shaft puller?
0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.
How do I make a graphite shaft puller?
0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.
How do you remove golf club shafts?
0:042:32How To Remove A Steel Golf Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also use a heat gun but it's going to take three times as long. The other things that you'reMoreYou can also use a heat gun but it's going to take three times as long. The other things that you're going to need or a club making vice vice clamp some heavy-duty gloves and probably a knife.
How do you remove a ferrule from a graphite golf shaft?
0:223:50How to Remove Ferrule from Steel Shaft Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipGently on the shaft. There's apply the heat. You're gonna see the ferrule start to bubble. Become aMoreGently on the shaft. There's apply the heat. You're gonna see the ferrule start to bubble. Become a bit more smooth-looking kind of like. You know it's getting warm honestly. Does not take. Much.
Can graphite golf shafts be reused?
Reusing graphite iron and wedge shafts. Along the lines of what fupresti said, as long as they're pulled properly you should be able to reuse a graphite shaft indefinitely.
Series Navigation
It is important to know the proper technique for removing a graphite shaft. A graphite shaft could be ruined forever if removed by the conventional twist and pull method that we use for steel shafts. The fibers in the shaft tear apart when you do this. In this video, I will show you the correct (and cheap) way to remove a graphite shaft.
Removing an Adapter from a Wood or Driver
The process for removing an adapter is very similar to removing a graphite shaft with a minor twist as shown in the video below.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
How much does it cost to replace a golf shaft?
Most retailers will charge $15-$25 to install a shaft, once a club is re-shafted it needs a new grip which ranges from $3-$12, the average cost to replace a golf shaft is $18-$37 per club. Clubs are either graphite or steel, reshafting a graphite club far more expensive.
How much does it cost to install a golf grip?
Labor costs vary as much as the price, most retailers will charge $15-35 but it can even be as high as $100, will grip installation costing around $3-5 in most Golf shops, the ProShop mention above charges $3 labor per grip.
How to clean a hosel shaft?
Once the shaft is removed the inside of the hosel needs to be cleaned, use sandpaper to clean it inside, wrap some around a dowel rod slightly smaller than the inside of the hosel, and dip it around, tap any powder left inside and dip a q-tip in acetone to finish.
How long to let a golf shaft rest?
Don’t use too much and cause a mess. Reinsert the shaft, now align the shaft graphics to how you want, let it rest in the playing position for 24 hours. After, apply some acetone to a paper towel and hold the towel to the ferrule and spin it.
How far do the tips of a driver go?
You must know how far the tips of the shafts go, most drivers are 1″ but it varies to 1.25″
Can you use epoxy glue to glue golf clubs together?
Epoxy (glue) come in different types and have different uses, not all of them will work for keeping a Golf club together. Yes, you could use lighter fluid instead of grip solvent but they make the grip smell like gas for a long time.
Can you use lighter fluid instead of grip solvent?
Yes, you could use lighter fluid instead of grip solvent but they make the grip smell like gas for a long time. You have to cut a shaft to a specific length with a tube cutter, it’s even more difficult with one, you could cut the shaft off and drill out the club’s hosel (where the shaft is inserted).
How much does a golf shaft cost?
Last but not least, for those who want only the best when it comes to their golf equipment, shafts can run as much as $600.
How Much Does it Cost to Replace a Driver Shaft?
Golf equipment manufacturers are becoming more cognizant of the important role that shaft plays in the performance of a driver. After all, the shaft is responsible for transferring the tremendous amount of energy generated by the golfer’s swing to the clubhead, which in turn impacts the ball and launches it into the air. The shaft, therefore, affects ball flight just as much as the head of the driver. (Source: Dick’s Sporting Goods – Pro Tips)
What is extra stiff shaft?
Extra stiff – This class of driver shafts is reserved for low handicappers and golfers who play at a competitive level. Long hitters play with extra stiff shafts on their drivers to not only take advantage of their length off the tee but also to control their ball flight and shape shots according to the course layout. Extra stiff driver shafts are designated with the letter “X.” Extra stiff flex shafts range in price from $30 to $600 (without installation).
What is a regular shaft?
Regular – This is the most common type of shaft flex and suits the typical recreational golfer who can routinely drive the ball 225 to 250 yards. This is an all-around shaft for players who are satisfied with their distance and want to maintain ball control. Regular flex shafts are designated with the letter “R.”
What is a driver shaft made of?
When it comes to material, the overwhelming majority of driver shafts on the market are graphite, which is a composite of graphite fibers and epoxy formed into what is essentially a hollow tube that is comparatively stronger than steel, but only half the weight. (Source: golfclub-technology)
Why is graphite important in golf?
It is the lightweight strength of graphite shafts that enables golfers to generate greater swing speeds , which, in the eyes of many, translates to longer distance off the tee. Since there is so much uniformity in driver shafts as far as the graphite material, the most important attribute as far as the recreational player is concerned is the amount of flexibility in the shaft or the flex . (Source: Golf Magazine)
What is the effect of flex in a driver shaft?
The amount of flex in a driver shaft has a significant effect on not only driving distance but also the golfer’s ability to keep the ball in the fairway (or in bounds, for that matter).
Can you pull a pro launch shaft by hand?
I have pulled a few by hand, never anything high end so if it didn't work no biggie. I did mess up the tip of a Pro Launch shaft, just trimmed it and used it in a 5 wood. Did another that was a mess, had to drill it out and throw the shaft away, but I have had several others where I had no issues. It's risky, but it can be done.
Can you pull graphite shafts without a puller?
Pulling a graphite shaft without a shaft puller is almost a guaranteed way to ruin a shaft. You might get lucky and not damage it, but not something I would risk. If someone said here is a shaft to use and by the way, I pulled it by hand, I would pass on it.
How to loosen a club shaft?
There are two ways to do this step. One way to loosen the shaft from the clubhead is to heat the hosel, or connector, of the clubhead with a blow torch until the epoxy that is used to bond them together becomes liquid. Be sure that you wear protective glasses while doing this process. The second way is to cut the shaft right above the hosel ...
How long does it take for epoxy to set on a golf club?
Allow about 24 hours for the epoxy to completely set before you finish your golf club. Decide on the length of the club, then mark it where the cut should be made. Since the graphite shaft might shatter when cut, put on a few layers of tape on the cut line before you use a band saw to cut it.
How to put a clubhead on a hosel?
Carefully place the tip of the shaft inside the hosel, ad twist the clubhead slightly to be sure that both the hosel and the shaft are covered thoroughly. Finally, pull the ferrule down to its proper position.
Can you remove a graphite shaft?
Actually, removing a graphite shaft, then replacing it, are easy to do if you follow these simple steps. Soon you will have virtually a new club, and dreams of lowering your score might be a reality.
How to remove a broken shaft from a golf club?
Insert the broken shaft into the vise and remove the shaft by using the heat gun to warm up the hosel and loosen the adhesive that holds the shaft in place. Use medium heat for graphite shafts and higher heat for steel shafts. Once the adhesive has started to melt, pull the broken shaft from the hosel, which is where the shaft meets the club head.
How to sand graphite shafts?
With the shaft still in the vise, use sandpaper to rough up the tip of the shaft, which will be inserted into the hosel. Graphite shafts may have coating on the end that should be removed with a sharp blade before sanding.
How to put a club shaft in a hosel?
Make sure the inside of the hosel is completely coated, then coat the tip of the shaft with epoxy. Slide the shaft into the hosel and turn the shaft so that the club head is properly aligned to the shaft. If there is a ferrule (small plastic piece), it should be inserted into the hosel first, then coat the interior with epoxy and slide the shaft in.
Can a golf club shaft be repaired?
Once a golf club shaft has been broken, it cannot be repaired, but it can easily be replaced.