Full Answer
How much does it cost to reshaft Irons?
How Much Does It Cost To Reshaft Irons? Expect to pay anywhere between $40-$100 reshafting a graphite shaft, if the shaft is steel expect to pay anywhere between $20-$75 per shaft, every replacement shaft needs a new grip which costs $8-$15, and labor costs $5-$35 depending on where you live.
Can golf irons be reshafted?
Yes, just like other types of golf clubs, golf irons can also be reshafted using a golf repair service. You may think that reshafting is expensive. But, there are certain situations where it is better to get the irons reshafted than buying new ones.
How much does it cost to reshaft golf clubs at Dick's?
Dick’s Sporting Goods will perform a reshaft on a set of eight clubs for $80. Reshafting golf clubs overview During the procedure, the older shafts on your iron or driver will be removed by heating the shaft with a heat gun. Once the older shaft is removed, the undercarriage will be cleaned up with a sandpaper until it is shiny in appearance.
How much does it cost to replace a golf shaft?
Most retailers will charge $15-$25 to install a shaft, once a club is re-shafted it needs a new grip which ranges from $3-$12, the average cost to replace a golf shaft is $18-$37 per club. Clubs are either graphite or steel, reshafting a graphite club is far more expensive.
How much does it cost to Reshaft an iron?
The average cost to reshaft your golf clubs is $24 per club plus the cost of the shaft and grip. A new iron shaft and grip can range between $10 and $95 while a new driver shaft and grip can range between $18 and $440.
Is it worth it to Reshaft irons?
Reshafting is just one way to keep your clubs performing at a high level. You can also benefit from regripping your clubs. Replacing worn-out golf grips can help make your clubs feel new again. Adding the right shaft to your favorite clubs can get you back on the course and working toward a new personal low round.
Does Golf Galaxy fit shafts?
During a shaft fitting at Golf Galaxy, our trusted advisors will analyze your swing and launch characteristics to determine the best shaft(s) for your game.
How long does it take to Reshaft a golf iron?
It takes 24 hours to reshaft a golf driver. If you use an epoxy such as the Tour epoxy, you can get done with the reshafting process really fast and your driver will be ready to use in about half an hour.
Is it easy to Reshaft irons?
Golf irons can be a bit easier to reshaft than a driver. If you are reshafting with steel irons, it is usually pretty straightforward. However, you will need the proper tools and space to complete this project.
Are steel shafts better than graphite?
Typically, steel shafts are much heavier, more durable and are generally less expensive than their graphite counterparts. They are more often than not made from stainless steel and they tend to weigh in between around 90g-120g. Torque or lateral twisting found in all graphite shafts is lower in steel irons.
What can I expect from an iron fitting at Golf Galaxy?
0:135:33Iron Fittings at Golf Galaxy - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe should fit you for your shaft both type and stiffness will fit you for the proper grip size andMoreWe should fit you for your shaft both type and stiffness will fit you for the proper grip size and the set makeup. So we got Shane here coming in to get fit for a set of new hires.
What happens at Golf Galaxy fitting?
Our expert fitters will address your loft (distance control and gapping), lie (directional control), shaft flex (distance and trajectory control, feel), club length (distance and accuracy control, comfort), grip size (directional control, feel and security), swing weight (feel and swing control) and set makeup ( ...
How do I Reshaft my irons?
2:2022:36GOLF CLUB BUILD - How to reshaft your irons Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the shafts you don't need a shaft puller. Anything like that you can just heat them up andMorePull the shafts you don't need a shaft puller. Anything like that you can just heat them up and twist them off because it's a steel shaft.
Do iron shafts make a difference?
It can give you the best chance at striking the center of the face that will result in optimal launch conditions on the course. It absolutely has an effect on how well you can play. The shaft is similar to the transmission of a car. While it's not the engine, it's still extremely important.
Can I replace my steel shafts with graphite?
On golf clubs that are not forged, light work will still be included, but you can replace the steel shafts with graphite. You will have to heat the clubhead and remove it, and you may have to buy a new grip. It's a little involved, but completely doable.
Can you change golf club shafts?
Shafts can be replaced at golf pro shops and most golf stores, but it is also a fairly easy project to do yourself. Replacing your own shaft can save time and money, and allow you to try a new shaft without purchasing new clubs.
How to mark the shaft of a golf club?
Slide a 48-inch ruler behind the club. Use a felt tip pen to mark the shaft an 1/8 of an inch below the desired playing length. Note: The grip cap will extend the club's length by an 1/8 of an inch.
How to install a ferrule on a golf club?
If a ferrule is to be installed, slide the ferrule up the shaft, and then mix the epoxy. Dip the tip of the shaft into the mixed epoxy, making sure that a small glob of epoxy remains on the tip. Insert the shaft into the club head's hosel. Rotate the shaft while sliding it in and out of the hosel, evenly coating the shaft and hosel with epoxy.
How to put shaft on club head?
Insert the shaft into the club head's hosel. Rotate the shaft while sliding it in and out of the hosel, evenly coating the shaft and hosel with epoxy. Align the shaft graphics the way you want them by rotating the shaft. Then, tap the butt end of the shaft on the floor to seat the tip against the bottom of the hosel bore.
How to remove a steel shaft from a metal?
Steel Shafts: To remove a steel shaft from a metal wood or iron, place the shaft in a super lock tight shaft holder. Tighten the STSL in a vise. If there is a plastic ferrule in place, wrap a wet paper towel around it to prevent burning. While wearing protective leather gloves, aim the flame of a torch at the hosel.
How to improve golf game?
Try a new shaft on your golf club. It's an inexpensive way to learn which kind fits you best. The right shaft can improve your game.
How much does it cost to reshaft a golf club?
How much does reshafting golf clubs cost? Depending on the quality of the shaft, the cost can be anywhere from $15 to as much as $150 per club. If the shaft is a higher name brand shaft, it is going to be near the higher end, while a lesser known brand can be toward the lower end. Materials will also play a role.
How to remove old shafts on iron?
During the procedure, the older shafts on your iron or driver will be removed by heating the shaft with a heat gun. Once the older shaft is removed, the undercarriage will be cleaned up with a sandpaper until it is shiny in appearance. The newer shaft will be cut to size and applied to the golf club using an epoxy.
What is re shafting a golf club?
Re-shafting a golf club is the process of removing the old shaft and replacing it with a newer one. Golfers may often have this process done if they want a new shaft or the previous one broke. Installing a new shaft can be a time-consuming process for many golfers, and this is one of the main reasons that most turn to a professional.
Do golf clubs offer discounts?
If you are already a member of a golf club, check with them first as they may offer discounts to members.
cvvorst
I want to preface this thread by saying that the guys in my golf galaxy are for the most part nice, semi knowledgeable people who I get along with.
Flop Shot Master
Thats a little higher than what i usually pay. I believe i pay around $21 to have a shaft pulled and another installed. No grip or anything
cvvorst
Wow. Never realized it cost $18 to do that. You can buy a giant thing of epoxy for half that. I literally stood there and watched them install it, took 45 seconds.
Brad Thor
I have worked on by own equipment since wooded drivers and no way would anyone charge less than $30 to remove and reinstall another shaft.
TheGeekGolfer
I'll so tired of the argument that it only took them x number of minutes to do it. Yeah, because they have done hundreds of them. So, you should pay LESS because they are better? How much time did it save you? You're covered if they break it. Sounds reasonable to me! [rant] This happened to me the other day. Fixed a lady's computer, remotely.
coreyl
Now thats expensive. $99 for a 1/2 hour, that's almost on that Lawyer time...she should have saved herself a little money and bought a new machine.
cvvorst
Part of the reason I asked was because I've had iron sets reshafted for under $100. It seems I've offended some of you by asking if the price was fair, which is odd considering that's what this forum is for... I'll stand by what I said. A job that takes under a minute shouldn't cost $18. Since it does, I'll be doing it myself in the future.
Better Your Best
You only get to carry 14 clubs – make sure each one is the perfect fit for your swing.
Game-Changing Technology
TrackMan utilizes groundbreaking dual radar systems to analyze every aspect of your swing and ball flight to find the best fit for your clubs.
More Ways to Elevate Your Play
During your complimentary session, one of our trusted advisors will answer questions and make suggestions about which clubs you should be playing to score low this season.