How much does it cost to replace a serpentine belt?
Below are some of the serpentine belt replacement cost examples for some vehicle models using the average shop labor rate of $100 an hour: 2010 Chevrolet Malibu with the 2.4-liter engine – labor is 0.7 hours, an ACDelco belt is $15 or $29 at dealer prices.
How much does it cost to replace a belt on VW Jetta?
The total job cost would be about $85 at an independent shop and about $100 at a dealership. 2007 Volkswagen Jetta with a 2.5-liter engine – labor is one hour, a Gates replacement belt is about $12 or an OE belt is about $42.
What is a serpentine belt on a car?
A serpentine belt is a long rubber belt that is used to keep multiple car systems running all at once. It’s located on the car engine and some of the systems that it supports are the alternator, air conditioning, water pump, power steering, and cooling fan. It’s essentially a giant rubber band which is threaded over,...
How much does it cost to replace a motocraft belt?
With the dual alternator option, a Motocraft belt is about $38 or $82 through a dealership. The total cost for the job is about $248 at an independent shop or $292 at a dealership.
How much does a serpentine belt job cost?
But what does a serpentine belt replacement cost? Of course, it depends on your make and model as well as labor costs, but in general a replacement serpentine belt costs around $70-$200 (plus taxes and fees), including around $50 for the belt and around $150 for the labor.
Can I drive my car if the serpentine belt is broken?
Under no circumstances can you drive a vehicle without a serpentine belt because the serpentine belt serves the important function of delivering antifreeze to important parts of the engine. The serpentine belt drives the water pump, and without it, there is insufficient coolant flow to maintain the engine temperature.
How much is a timing belt job in a Volkswagen GTI Golf?
Belts themselves aren't that expensive. The real cost is in the labor, because a lot of parts need to be disassembled to get to the belt. Shopping around to get a few quotes is your best bet to get the best deal, but you can expect to pay anywhere from $409 to $919 (including parts and labor).
What are the signs of a failing serpentine belt?
If you suspect your serpentine belt is failing, watch out for the following symptoms:Squealing noise from the front of the vehicle. If you notice a squealing noise coming from the front of your vehicle, it could be from the serpentine belt. ... Power steering and AC not working. ... Engine overheating. ... Cracks and wear on the belt.
How long does it take to fix a serpentine belt?
It can take anything from 15 minutes to an hour (two at the most) to repair or replace a bad serpentine belt with a new belt.
Can you replace a serpentine belt yourself?
Automatic belt tensioners, standard in most cars now, make changing a serpentine belt a simple DIY repair. Follow the clear photos and step-by-step instructions and you'll be done in 15 minutes.
How much does it cost to replace a timing chain on a GTI?
The average cost for a Volkswagen GTI timing chain tensioner replacement is between $988 and $1,145. Labor costs are estimated between $601 and $759 while parts are priced at $387. This range does not include taxes and fees, and does not factor in your specific model year or unique location.
When should I change my timing belt GTI?
Every 60k-90k miles. If an engine is equipped with a timing belt, the timing belt must be replaced at the service interval specified by the vehicle manufacturer regardless of whether or not any problem is visible, typically in the range of 60,000 to 90,000 miles.
When should the timing belt be changed on a VW GTI?
Volkswagen recommends changing your timing belt every 100,000 miles. The timing belt connects the engines crankshaft with the camshaft.
What happens when serpentine belt breaks while driving?
If a serpentine belt breaks, a car won't be drivable and will have to be towed. If the engine runs without a serpentine belt, it might overheat as the water pump will no longer work. A broken belt can also damage other parts.
Is serpentine belt same as drive belt?
A serpentine belt actually has the ability to transmit the power between your power steering pump, your alternator, air conditioning compressor and water pump, whereas your drive belt simply operates them..
What does a worn belt sound like?
As these belts wear out, they can begin to squeak or squeal. They make noise because there is not enough tension on the belt, or because the pulleys are misaligned or weak. Often, simply changing the belt will make it stop squealing. The noise isn't usually a danger, though it does sound alarming.
What is a serpentine belt?
A serpentine belt is a relatively long, flat, multi-ribbed belt that is driven by the engine’s crankshaft pulley. The belt drives many, and often all, of the engine accessories such as the alternator, air conditioning compressor, power steering pump, water pump, and air pump. The serpentine belt is tensioned by a hydraulic or spring-loaded automatic tensioner. Some older cars use a serpentine belt to drive most accessories but will also have a shorter v-style belt to drive, for example, the power steering pump.
How long does a serpentine belt last?
On many cars, the expected service life of a serpentine belt is around 90,000 miles. Should the belt fail well prior to that, a very careful inspection should be performed to check for out-of-alignment pulleys, a possibly out-of-position crankshaft harmonic balancer on which the drive pulley is mounted, binding pulleys, or a defective belt tensioner.
Why should attention be given to serpentine belt routing?
Attention should always be given to serpentine belt routing, since proper routing is critical to proper belt tension, and function of the driven components.
How long does it take for a serpentine belt to overheat?
Engine overheating. Often, the serpentine belt drives the water pump. In those applications, if the belt breaks the engine will overheat in seconds to minutes. If the belt is inadequately tensioned, you may notice higher-than-normal engine operating temperature.
What are the signs of a belt failure?
Should the belt fail or wear out prematurely, you may hear noise or you may see visible signs of deterioration such as missing chunks of rubber, excessive cracking, or a shredded appearance on the edge of the belt.
How many miles does a belt need to be replaced?
Regularly scheduled maintenance. Typically, belt manufacturers recommend belt replacement at 90,000 miles. However, the belt must be inspected for wear or damage at regular intervals prior to this high mileage.
Do mechanics run idler pulleys?
Prior to removing the belt, the mechanic must run the engine to determine if the idler pulley and the belt tensioner are noise-free. Those rotating components have grease filled bearings and are subject to wear. In addition, the mechanic will ensure that all pulleys and accessories are turning in the same plane. These steps help make sure your new belt will operate trouble-free for its full-service life.
What is a serpentine belt?
It also has to generate electricity, assist with power steering, cool off the passengers, and keep itself cool. The serpentine belt - sometimes referred to as the fan belt, alternator belt, or accessory drive belt - is used to spin, or "drive," several components attached to the engine. It drives the alternator that powers the electrical system and recharges the battery. It also drives the power steering pump, the air conditioning compressor, and the water pump. (The water pump circulates coolant through the cooling system ). In the past, multiple drive belts were used to turn pulleys attached to these components. Today, most vehicles employ just a single belt - the serpentine belt - to do the job.
How often do serpentine belts need to be replaced?
Replacement intervals vary by vehicle and driving conditions. We typically see this part replaced approximately every 100,000 miles.
What are the symptoms related to a bad serpentine belt?
Over time serpentine belts stretch, crack, and the ribs that ride on the accessory pulleys being to wear smooth. A squealing noise that increases with engine speed or as engine driven accessories are turned on may be noted. The noise is caused by the belt slipping on the pulleys, insufficiently driving them. Ineffective air conditioning, a battery warning light, or intermittent power steering assist can result from this.
Why does my serpentine belt make a squealing noise?
The noise is caused by the belt slipping on the pulleys, insufficiently driving them.
Can I drive with a serpentine belt problem?
A slipping belt means one or all of the accessories are not being driven properly. Loss of air conditioning, electrical power, power steering, or water pump and fan drive are possible depending on the severity of the wear. If left for too long the belt can shred or come off of the pulleys. The belt should be inspected as soon as is convenient to protect against becoming stranded.
What is serpentine belt?
The function of a serpentine belt is very simple: it transmits engine power from the crankshaft to the driven accessories. Typically, those would be the water pump, the alternator, the AC compressor, and the power steering pump. Some engines have fewer things while others (such as diesel engines) have more.
How does a serpentine belt work?
The operation of replacing a serpentine belt is essentially pivoting the tensioner away and slipping the old belt off , then, positioning a new one in its place and releasing the tensioner.
What happens if a belt leaks?
If there is a leak that has gotten on the belt, it can leave gummy deposits or even fragments of the old worn belt lodged in the pulley grooves. It’s always a good idea to check these and clean as necessary to avoid further problems. And, of course, address leaks to prevent a recurrence.
How much does a Motocraft belt cost?
With the dual alternator option, a Motocraft belt is about $38 or $82 through a dealership. The total cost for the job is about $248 at an independent shop or $292 at a dealership. This would be on the costly end of the spectrum. Of course, the cost to replace the serpentine belt for both the parts and labor varies everywhere – from region ...
How much does a Dayco belt cost for a 2012 Ram 1500?
2012 Ram 1500 with the 5.7-liter engine – labor is 0.4 hours, a Dayco belt is about $20 while the factory belt runs at around $43. The total job cost would be about $64 with the aftermarket part or $104 with the OE part. 2008 Ford F-250 with the 6.4-liter diesel engine – labor (by book time) is 2.1 hours.
Why is my belt making a noise?
Sometimes a failed belt is caused by a failing bearing and sometimes, what is taken for belt noise turns out to be noise in something driven by the belt. It’s not always possible to verify a problem prior to removing the belt. Another thing that can go wrong is pulley alignment.
How much does a 2010 Malibu belt cost?
2010 Chevrolet Malibu with the 2.4-liter engine – labor is 0.7 hours, an ACDelco belt is $15 or $29 at dealer prices. The total job cost would be about $85 at an independent shop and about $100 at a dealership.
