How much should a golf shaft weigh?
Getting the correct weight of your shaft is an important factor to consider as well. Shafts can range anywhere from 40 to 135 grams. Typically the rule of thumb is that a golfer with a slower swing speed will benefit from using a lighter shaft, and you would add weight as swing speed increases.
What is pressure in the golf swing?
The more force — pressure — a golfer applies into the ground at the start of their golf swing, the more they can push off the ground later on. It’s a powerful move that helps golfers pull the club down faster and hit the ball longer.
Does the shaft know how fast the club head is moving?
The shaft has no idea how fast the club head is actually moving. It only responds to this. A real-world example would be to compare the swings of two legendary golfers, Nick Price and Fred Couples. Price had a lighting quick tempo, and a much shorter swing versus the long, flowing swing of Couples.
Should you tip your golf shafts?
In most cases, shaft tipping is done to steel iron and wedge shafts but occasionally is done in graphite shafts for woods and drivers as well. Lastly, tipping won’t do much to affect spin rates and launch angle — two popular misconceptions when it comes to trimming the lower end of a shaft.
How hard is it to snap a golf club?
Golfers have been known to snap a club over their leg, or slam a club on the ground and potentially break it. Unfortunately, golf clubs are not built to hold up to this type of abuse. It is not as difficult as you may think to break a golf club and unfortunately it is quite expensive to fix one.
What is the torque of a golf shaft?
"Torque" is a property of golf shafts that describes how much the shaft is prone to twisting during the golf swing. All shafts, steel and graphite, exhibit torque, which is measured in degrees. A high-torque shaft will twist more than a low-torque shaft. Put another way, some shafts resist twisting better than others.
How do you pull a golf shaft?
6:2514:27pulling a golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I like to do is I like to pinch. Down. And then pull back pinch down and then pull back. AndMoreAnd I like to do is I like to pinch. Down. And then pull back pinch down and then pull back. And this way you don't scrape a shaft.
How do you pull a graphite shaft?
0:053:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain using a butane torch you can actually really focus the heat which is a lot better than sayMoreAgain using a butane torch you can actually really focus the heat which is a lot better than say trying to use a heat gun which could end up damaging. The fibers of the golf shaft.
What is considered low torque golf shaft?
Amount. A low-torque shaft may allow only 2 degrees (or less) of twist, while a high-torque shaft might go all the way to 6 degrees. That might not sound like a lot, but it certainly can affect your accuracy.
What does tipping a golf shaft mean?
“Tipping” or “tip trimming,” as it's sometimes called, means trimming a club shaft from the clubhead end, not from the grip end where it's most often cut.
How do you make a golf club shaft puller?
0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.
Can you reuse a golf shaft?
However, if the shaft tip stays intact, take a closer inspection of the tip section to see if you notice any longitudinal cracks or delaminating, or basically anything that you think would be considered damage. If not, there is a good chance you could reuse the shaft into another head or the same head later on.
How do you Reshaft a golf club at home?
2:2522:36GOLF CLUB BUILD - How to reshaft your irons Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp the house'll. Pull the shafts you don't need a shaft puller. Anything like that you can just heatMoreUp the house'll. Pull the shafts you don't need a shaft puller. Anything like that you can just heat them up and twist them off because it's a steel shaft.
Can you pull a graphite shaft without a shaft puller?
Well, the general process for pulling a graphite shaft is just about the same, but there are a few key differences. You need to take more care and HAVE to use a shaft puller. Otherwise, your new fancy and expensive exotic shaft could be at serious risk for major damage.
Can you pull a driver shaft?
The good news is that steel shafts are pretty tough and resilient. A simple way to pull a steel shaft out of your clubs is with just your hands and a torch. It's important to remember that the club head and the shaft are going to get pretty hot so you need the proper materials to handle the heated metal.
How do you pull a fairway wood shaft?
1:054:56Club Building 101: Pulling a Shaft from a Bonded Driver - YouTubeYouTubeStart of suggested clipEnd of suggested clipGet it set up. And you'll see that it's already starting to push the ferrule. That's fine startingMoreGet it set up. And you'll see that it's already starting to push the ferrule. That's fine starting to really mush. It.
How do you measure torque on a shaft?
To calculate load torque, multiply the force (F) by the distance away from the rotational axis, which is the radius of the pulley (r). If the mass of the load (blue box) is 20 Newtons, and the radius of the pulley is 5 cm away, then the required torque for the application is 20 N x 0.05 m = 1 Nm.
What happens if golf shaft is too stiff?
If your golf shaft is too stiff and your swing speed is too slow, your well-struck shot will be limited on both carry distance and shot trajectory; a too-stiff golf shaft will most often lead to weak fades or slices.
What is a 5.5 shaft flex?
Stiff – 5.5. Stiff Plus – 6.0. Extra Stiff – 6.5. Extra Stiff Plus –7.0.
What weight driver shaft should I use?
Briand's recommendation is to use your current driver shaft as a baseline. If your shots tend to be low and with little spin, try a slightly softer flex. If your shots are ballooning, try a stiffer flex. If you're caught between two flexes, you can “tip” a softer flex to make it stiffer in the tip section.
How long to heat a golf club hosel?
Remember to always keep the heat moving 360º around the hosel, don't keep it in one place. Heat the hosel evenly on all sides for approximately 15-20 seconds. Gently apply pressure to extract shaft from hosel - The hydraulic pump will "push" the club-head up and off the end of the shaft.
Where should the round metal plate be on a golf club?
The round metal plate (as seen in photo) should be directly against the top of the hosel (to which we just removed the ferrule from). This allows the metal plate a good base to "push" the club-head up and off the end of the shaft.
Does Spargo Golf have shafts?
Spargo Golf pays close attention to age of the shaft, condition of the graphics and signs of usage. No shafts with questionable tips and appearances are saved. On occasion, Spargo Golf will inventory discontinued shaft s which have a higher request rate i.e.- RCH 60 series from Callaway and Cleveland Launcher Gold Series from the early 2000's. Customer's can be confident that the shaft pull-out is fully prepared and cleaned to be installed in their golf clubs. It is quite common that many of our shafts are pulled new or with minimal use.
What is pressure in golf?
Pressure, in a nutshell, is a measurement of how much force is being applied to a given area. In golf, we use pressure to measure how much force being applied by our feet into the ground. It’s become an important of the way golf coaches teach.
What is the force that a golfer applies into the ground at the start of their swing?
The more force — pressure — a golfer applies into the ground at the start of their golf swing, the more they can push off the ground later on. It’s a powerful move that helps golfers pull the club down faster and hit the ball longer.
How does measuring the ground help golfers?
Being able to measure how we’re using the ground, how we’re pivoting back , when we’re applying the most pressure during the downswing, allows golfers to really actually know if we’re making significant changes or not. It’s taken a concept that was once only a feel and given concrete data for players to get feedback from.
What foot is the pressure moving in the backswing?
What we typically see in the golf swing is the pressure moving more towards the trail foot in the backswing and then forward to the lead foot in the follow through.
How do coaches measure pressure?
The way coaches measure “pressure” is with a device like BodiTrak or SwingCatalyst, which shows you a heat map of where the most force is being applied by your feet. For instance, if you rock back on your heels you’d see that the “heat map” of pressure lights up red to illustrate more force being applied to your heels.
When helping a player understand how they need to be pivoting and loading into their backswing, it’s?
When helping a player understand how they need to be pivoting and loading into their backswing, it’s incredibly valuable to have real numbers to visualize exactly what’s going on vs what they’re feeling.
Who is the biomechanist for golf?
One of the experts in this field is biomechanist Dr Scott Lynn who has been helping golfers find their dominant leg and then understanding how to best apply pressure for their swing.
How much weight should a golf shaft be?
Weight. Getting the correct weight of your shaft is an important factor to consider as well. Shafts can range anywhere from 40 to 135 grams. Typically the rule of thumb is that a golfer with a slower swing speed will benefit from using a lighter shaft, and you would add weight as swing speed increases. As you might expect at this point, there are ...
Why is it important to choose the right shaft for golf clubs?
It can give you the best chance at striking the center of the face that will result in optimal launch conditions on the course. It absolutely has an effect on how well you can play.
What does it mean to choose the wrong shaft for a golf club?
Choosing the wrong shaft will make it much harder to access the center of the face more consistently on the course , and the last thing we want you to do is to make golf harder on yourself!
Why didn't Nick Price find a stiff shaft?
Regardless of the similarity in their swing speeds, Nick Price couldn’t find a shaft stiff enough for his swing because he would apply such an enormous amount of force, whereas Couples didn’t need as stiff of a shaft because of his smooth tempo.
What is fitting in golf?
When we put a customer through a fitting, we determine the right profile, weight, and flex that is required. Essentially we are writing a prescription for the golfer’s swing, and order the shaft to match what we believe will help them the most.
Why is shaft profile important?
Getting the right shaft profile for your swing is very important. It will greatly affect your ability to hit quality shots on the course . There is a lot of confusion in the golf shaft industry. With no standards for performance, the quality greatly varies, and often you get what you pay for. We hope that we have cleared up some ...
What is the most misunderstood product category in the golf industry?
One of the most misunderstood product categories in the golf industry is shafts . There are plenty of myths and mistruths out there that we wanted to clear up for you in this article and share what we have learned at Pete’s Golf over the past several decades.
Introduction – DIY Golf Shaft Pulling Tricks
We previously wrote about “ How to Pull a Golf Shaft ” where we cover the basic technique for properly and safely pulling both steel and graphite golf shafts. While that technique is a great best practice, and the only foolproof (-ish) safe way to pull graphite shafts, there are a few hacks you can use for pulling steel shafts at your home.
The Stove
This is the same technique as “by hand” but you use the stove for your heat source. I’ve been in a couple of random situations where I didn’t have a propane torch or heat gun at my disposal and had to pull a steel shaft from a head. All I did was fire up a burner on the stove and use it to heat the epoxy.
In a Vise
The vise technique is one of the great at-home DIY golf shaft pulling tricks. It’s not dissimilar to the “by hand” technique, but gives you a little more leverage and keeps your hands away from the heat. For this technique, you can approach in two different ways.
Boiling Water
This is my absolute favorite DIY golf shaft pulling trick based on ingenuity alone. What’s nice about this technique is that it works well and makes saving your sweet custom ferrules feasible as long as they weren’t super epoxied on. In order to do this, fill a pot with enough water to submerge your club head in.
Conclusion
Like I said in the intro, I’m going to recommend using traditional shaft removal techniques 100% of the time. You can find that approach here . That said, there are situations that may require an alternative approach and hopefully these DIY golf shaft pulling tricks will help you out there.
How to prevent paint scortching on golf clubs?
Then attempt to twist the club head from the shaft. Move the heat in a back and forth motion while moving around the hosel area to prevent paint scortching (burning). If the first attempt did not work wait about 30 seconds and do it again.
How to discolor graphite shafts?
I am an expert at ruining graphite shafts. Even with a vise and a puller, you have to be very careful and not apply too much heat or the graphite will ruin. You have to be worse than me to ruin steal shafts. However, if you use a propane torch you can discolor the hosel, but you only want to heat it up enough to melt glue. 150 degrees or so. To discolor the steel you need to be in the 300 range I think.
How much equipment do you need to make graphite?
If you are doing steel you need a $20 torch and towel. On graphite you need to add a $20 bench vise $5 rubber jaws or use old shafts and a pry bar.
How high do you heat up a propane torch to discolor steel?
However, if you use a propane torch you can discolor the hosel, but you only want to heat it up enough to melt glue. 150 degrees or so. To discolor the steel you need to be in the 300 range I think. Not that high, but definitely over heated.
Why do I prefer a torch over a heat gun?
I prefer the torch as I can see the heat being applied and where. The heat gun covers a larger area. It's not a big deal but I'm more comfortable seeing where I am applying heat than estimating.
Can you overheat a golf club?
Not that high, but definitely over heated. The trick is to measure the amount of time you are applying heat and pull the shaft just as the epoxy loses it's bond. Unfortunately the needed amount of time varies with the epoxy used, and the heat source because different heat guns give different amounts of heat. These days I bring my clubs to be pulled by a trusted club maker. I've discolored more than enough hosels so I only pull my older clubs.
Can you use a pry bar on graphite shafts?
The problem I have run into with graphite shafts is not the actual puller but in applying too much heat. A vise with a pry bar works fine, but too much heat is a deal breaker. What I do, is apply a little heat, try the pry bar, then a little more heat, and try again, and continue until the bond in the epoxy is broken. It take much less heat than i realized when I first started doing it.
How long is a Spargo golf shaft?
It is important to realize that the length, listed on each shaft, is the raw length. Actual playing length of most of these shafts will be between 1 1/4" - 1 1/2" longer. For example, a 43 1/2" pull-out will play to 45" in most of today's drivers, and a 41 1/2" pull-out would play to 43" in most of today's 3 woods. It is also important to note the tip diameter of the shaft you are searching for. Each shaft in the Spargo Golf Inventory lists shaft tip diameter. Many of today's Drivers use .350 tip diameter shafts, so if you choose a .335 tip diameter shaft, you will need a shim to properly install the shaft.
Does Spargo Golf remove epoxy?
It is quite common that many of our shafts are pulled new or with minimal use. Spargo Golf carefully Pulls, Abrades, Removes Epoxy in the Shaft Tip and Cleans each Shaft. Upon finishing the Prep process, Spargo Golf Performs Spine Alignment and Marks each shaft's Neutral Bend Point. This added step is performed at no additional cost to the Customer.
Does Spargo Golf do re shafting?
Spargo Golf offers Re-shafting Services as part of our Shaft Pull-Out Site. Customers can choose the shaft they like, the grip they desire, and then select the Spargo Golf Installation option. Upon receiving your Club, Spargo Golf will perform the Re-shaft, including ferrule, epoxy, spine alignment and proper swingweighting of your club. In most cases, Reshafts are performed the same day the club is received.
Does Spargo Golf work on golf clubs?
Spargo Golf understands that not all Golfer's can work on their golf clubs. In searching for Club Re-shafting or Club Repair Professionals, Spargo Golf highly recommends the AGCP (Association of Golf Clubfitting Professionals) . The members of the AGCP are the leaders in their field.
Why do golfers tip their shafts?
Better players tend to make the most use of this technique in order to fine-tune their shafts to precisely the amount of flex and feel they’re looking for. And sure, they could just as well switch to a different shaft, but tipping affords even greater fine-tuning to a particular flex profile. In most cases, shaft tipping is done to steel iron and wedge shafts but occasionally is done in graphite shafts for woods and drivers as well.
When you tip a shaft, do you need to have parallel shafts?
When you tip a shaft — which by the way, you need to have parallel shafts to do this — you alter how the shaft performs by making it slightly stiffer and increasing torque for less twisting through impact.
How does tipping differ from “shaft stepping”?
Shaft stepping, another common practice seen usually among better players, means altering your club’s shaft profile by offsetting your shafts based on what iron they’re designed for. A “hard step” is to put a 5-iron shaft into a 4-iron clubhead and so on through the set. This makes the shaft play a little stiffer. A “soft step” is the opposite — it means putting a 3-iron shaft into a 4-iron head (and so on through the set) to make the shaft play a little softer.
What does it mean to tip a golf club?
“Tipping” or “tip trimming ,” as it’s sometimes called, means trimming a club shaft from the clubhead end, not from the grip end where it’s most often cut. ...
What is a hard step in golf?
A “hard step” is to put a 5-iron shaft into a 4-iron clubhead and so on through the set. This makes the shaft play a little stiffer. A “soft step” is the opposite — it means putting a 3-iron shaft into a 4-iron head (and so on through the set) to make the shaft play a little softer. To receive GOLF’s all-new newsletters, subscribe for free here.
What does cutting off a shaft tip do?
Cutting off a section of the shaft tip can make it feel as if it were stiffer.
What is a parallel shaft?
A parallel shaft is one that has a constant diameter from the tip and up to a specified distance on the shaft. Conversely, a taper tip is as it’s described — the shaft tapers towards the tip. Most new clubs (irons and woods) are designed to accommodate parallel shafts, but can also accommodate a taper shaft using brass adapter shims.
How to pull a golf club?
To do this, you’ll need a partner. Stand upright and hold a club horizontally tight across your chest. From behind, have someone move you by pushing you from both sides of the club. You will notice if you look in a mirror, that your head will move about in both directions and you will likely not make a 90 degree turn. Now, have your partner pull the end of the club back behind you. You will be amazed at how easily you can make a full shoulder turn and how much “tighter” and smaller the movements feel when compared to pushing.
What is push vs pull golf?
The concept of “Push vs. Pull” is central to the Rotary Swing Tour. Sir Isaac Newton determined that all movement is either a push or a pull. You can envision this very simply by thinking back to the days where golfers actually walked the course with the assistance of pull carts. If you ever used one of these, you noticed right away that it was much easier to keep the pull cart moving in a straight line when you let it trail behind you and you pulled it. When you tried to push it from behind, you would invariably develop a little “zig-zag” path as the movement seemed less stable. But why?
How to do a centered rotation in golf?
Using the scapular motion of gliding it across the ribcage in toward center helps create centered rotation exactly like what we are looking for and gets the golfer connected to the big muscles of his core. It’s a win-win for the backswing. This movement is a key component for the golfer learning to create a “pulling” motion, which, as we have learned, is necessary for creating an efficient, centered rotation and will be a key to helping all your students create a 90 degree or greater shoulder turn in the backswing. While we have gone to great lengths in this chapter to emphasize the pulling motion desired to create centered rotation, it should be noted that this is not the only force that is going on. In fact, technically speaking, it is a "push-pull" throughout the golf swing. As an example, we emphasize pulling with the left oblique on the downswing because this is what helps clear the hips back out of the way, providing room for the arms on the downswing. Most golfers push from the right side during the downswing and end up coming out of their spine angle. This is more instinctual for most but creates a number of common swing faults. When the golfer begins to focus his efforts on pulling, it is often a new feeling for him, so that's all he "feels." However, while he may feel the left oblique firing, the right oblique is also helping as they work in pairs in rotating the torso. It is important for the student to feel pulling over anything else in most cases, but as an expert golf instructor, you need to understand that both sides are working.
What happens when you pull on the downswing?
As you're coming down, you're going to push from the other side. Pulling helps you get good shoulder turn, even before the top of the swing. If you're flipping or if you're getting a lot of axis tilt at impact, a lot of this can be from pushing from the right side.
What is the difference between a push and a pull cart?
When we look at the definition of a pulling motion in its simplest form, it is the act of moving something towards you; or towards center. A push is the exact opposite. If you are trying to push a box across the floor of your living room, are you effectively moving it away from you or toward you? The reason that the pull cart travels in a much straighter line when pulled is that the force acting upon it is always moving it toward a centralized point – YOU! When you stand behind it and push it, it could move in any number of directions, a full 360 degrees away from center. When we apply these concepts to the golf swing, some very interesting things begin to appear that make a lot of the old instruction adages like “get your left shoulder under your chin” obsolete. We would, in fact, tell the student to pull his right shoulder behind his head.
Which shoulder to pull in backswing?
Pulling the right shoulder into the backswing - instead of pushing the left shoulder under your chin - helps you get good shoulder turn at the top of the swing
How to understand centripetal force?
To fully understand centripetal force, imagine a ball on the end of a string attached to a stick. By moving the stick in a very small circular motion, the ball on the end of the string can be accelerated to terrific speeds with minimal effort by you.