Tape and mark the area to be cut, as you did with the tip. However, add 1/8 inch to the cut to account for the grip cap. For example, if your 9-iron shaft is 38 inches long after trimming the tip, trim 2 1/8 inches from the butt end to produce a 36-inch club after the grip is installed.
How much should I cut off my shafts?
This depends on what you’re looking for. The more you cut off, the more you change the flex profile (towards a stiffer shaft). Some shaft manufacturers actually list tipping guidelines on their websites to help you discern the right amount to cut.
How to cut a golf shaft?
Use a tube cutter for a steel shaft and a saw blade in case of a graphite shaft. Turn the cutting equipment on and cut the shaft through smoothly and slowly. Turn off the cutting equipment and remove the club. Smooth out the rough edges on the butt end of the golf club with sandpaper. Fix a new grip on the shaft end.
How much should a golf shaft be tipped?
Many pros have their shafts tipped as much as one or two inches. The idea behind tipping is to make the clubhead end of the shaft stiffer and even lower torque than it was designed to be to minimize twisting of the club at impact.
How much does the Flex change when the shaft is cut?
But it's impossible to state an across-the-board estimate of just how much the flex changes due to cutting, because that's individual to each shaft and the shaft's original design:
How much does it cost to cut iron shafts?
For many standard length clubs, you will need to trim somewhere between 1/2" to 1". The lengths are longer than needed (for standard clubs) to allow for longer than standard clubs for taller players. If you need your clubs to be 1" over standard, then you may won't need to trim at all!
How much does it cost to cut down a driver shaft?
Generally, this fee will be about $15 to $35 depending on where and when you get the work done. Replacing a shaft on a driver is a bit more work than regripping a club. Try to have it done by a reputable person who understands club fitting.
How much does it cost to Reshaft golf clubs?
The average cost to reshaft your golf clubs is $24 per club plus the cost of the shaft and grip. A new iron shaft and grip can range between $10 and $95 while a new driver shaft and grip can range between $18 and $440. The majority of the cost comes down to what type of shaft you want and what grips you like.
Can you cut your own golf shafts?
To do that, the DIY golfer will have to: Remove the existing grip. With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw. Re-install a grip on the newly shortened shaft.
How much does it cost to shorten shaft?
Any amount of cutting will slightly stiffen the club. It will probably go unnoticed if you take 1 inch or less off the club. Taking 2 inches off will change the flex of the club. If you are shortening irons, every 1 inch you shorten the club will make the iron effectively play 2 degrees flatter.
Is it OK to shorten a driver shaft?
Shortening the shaft will make the club shorter but it will also make the shaft stiffer and adjust the swing weight as well. Plus, the more length you remove, the less flex your club will have. Depending on how much you cut it down, it could move a regular flex to a stiff or a stiff to an extra stiff.
Is it worth Reshafting my irons?
Reshafting is just one way to keep your clubs performing at a high level. You can also benefit from regripping your clubs. Replacing worn-out golf grips can help make your clubs feel new again. Adding the right shaft to your favorite clubs can get you back on the course and working toward a new personal low round.
How far should you hit a 7 iron?
Average 7 Iron Distances are following: Beginning golfers- 100 yards (men) or 60 yards (women) Intermediate golfers- 135 yards (men) and 75 yards (women) Advanced golfers- 165 yards (men) or 140 yards (women)
Is it easy to Reshaft irons?
Golf irons can be a bit easier to reshaft than a driver. If you are reshafting with steel irons, it is usually pretty straightforward. However, you will need the proper tools and space to complete this project.
Does cutting a golf shaft make it stiffer?
In most cases, tip trimming a shaft makes it meaningfully stiffer. It also increases torsional stiffness, known as “torque,” which is a shaft's resistance to twisting. On the other end of the shaft is the handle, which is also generally trimmed some amount when building a golf club.
Is it easy to shorten golf clubs?
If you have purchased a set of used golf clubs that are too long, you can quickly cut them down to size with a hand-held rotary tool. You can also resize your old clubs and pass them on to your children. The shaft of a golf club is narrower at the head end to generate power on the swing.
How does cutting a shaft affect swing weight?
For every half inch of length added, the swingweight increases by three swingweight points. For every half inch of length removed, the swingweight decreases by three swingweight points.
How to shorten a golf club shaft?
Remove the grip from the driver using a hook blade or a utility knife, as well as the grip tape on the shaft. Measure the length that you want to shorten on the shaft. Add an extra 1/8 inch to this and mark the position using a permanent marker. Fix the golf club in position in a vise.
How long is a golf driver shaft?
The standard length for a male driver shaft used to be 43.5 inches for a steel shaft and 44 inches for a graphite club. However, in recent times, the standard driver length has been accepted as 45 inches. Typically, the length of a female golfer’s club is an inch lesser than that of a male golfer’s club.
How to make a golf club more upright?
By increasing or decreasing the shaft length by an extra half an inch will result in the club playing 1 degree more upright, or flat respectively. With a standard-length club, tall players tend to stoop quite a bit while short players will find themselves having to stand in a more upright position than required.
How to narrow down a golf shaft?
The best way to narrow down on the right shaft is to do test shots on the range with drivers of varying lengths. The right shaft length will help you to hit the golf ball with the driver much the same way that you would do with a wedge.
What is the difference between the length of the golf club and the length of the clubhead?
The length of the golf club’s shaft in relation to the overall length of the club defines the length of the driver shaft. Alternatively, this is the difference between the length of the overall golf club and the length of the clubhead. Generally, the longer your driver shaft is, the more difficult it becomes to have control over ...
When you shorten your golf shaft, do you keep in mind the after effects?
When you have decided to shorten your golf shaft, you must keep in mind the after-effects of doing so. How much and where you cut off the shaft has different effects on the golf club.
Is a golf club shorter for women or men?
You can use the same table given above as a reference for women. Remember that golf clubs for women are designed to be an inch shorter than men’s golf clubs. So, you will have to make your calculation accordingly.
Why trim a shaft?
Why trim or cut a shaft at all? When the manufacturers make a shaft, they do so in mind that is could be used for a wide number of golfers and applications, so the manufacturer makes the shaft longer than it will most likely be used in the final golf club. The number one reason for making the shaft longer is to accommodate taller players so they ...
Why do you need to trim a parallel shaft?
This is required to offset the increasing heads weights as the clubs become shorter and maintain the flex the manufacturer designed into the shaft for a finished club.
What is a combination flex shaft?
These "combination flex" shafts are designed to reduce inventory by being able to create multiple flexes from a single shaft rather than produce two different shafts. Here are the most common ones below.
What does a trimming chart show?
It is also important to understand the trimming charts show how much (if any) to take off the tip end (the skinny part or where the head will be attached). The trimming charts will not tell you an amount to take off the butt end (the fat part where the grip is installed).
Series Navigation
I know this might seem obvious, but be sure to measure and mark off the point at which you are cutting. Especially while tipping a shaft (you can’t undo this), it is important to have precise measurements. Use a sharpie to make your marks on the shaft. Here is a tutorial on how to measure golf clubs.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
How much should a golf shaft be tipped?
Many pros have their shafts tipped as much as one or two inches. The idea behind tipping is to make the clubhead end of the shaft stiffer and even lower torque than it was designed to be to minimize twisting of the club at impact.
What does cutting the shaft shorter do to a golf club?
The swing weight, or weight at the head of the club and any additional weighting inside the shaft, is still in place, and cutting the shaft shorter changes the balance of the club as well.
Why do tour pros have their shafts tipped?
Tour pros often have their shafts "tipped," or cut back from the clubhead end slightly to make the tip of the shaft stiffer. This enables them to keep the same length club but have a slightly stiffer shaft near the ball. Cutting a club from the butt end will have somewhat the opposite effect, making the shaft stiffer overall but shorter as well.
How does changing the length of a golf club affect the swing?
Changing swing characteristics: Changing the length of a golf club can moderately or severely change the swing characteristics of the club. Removing length from the butt end of the shaft also removes weight from that end and changes the swing weight and balance of the club. Cutting a shaft from one end or the other also changes the kickpoint ...
How to adjust length of golf club?
Step 1. From the butt: The easiest and quickest way to adjust the length of a club is to remove the grip and cut a given amount of the shaft off the butt end. Traditionally, this is how many youngsters get their first sets of golf clubs. Their parents cut the clubs down so they are easier for them to handle. Keep in mind, though, that cutting the ...
Is a shorter shaft stiffer than a longer shaft?
A shorter shaft is typically stiffer than a longer one. Although a shorter golf club shaft tends to be firmer than a longer one, it is important to understand the changes trimming a shaft will make to a club before making such a permanent change.
Can you cut a shaft from the butt end?
Cutting a shaft from one end or the other also changes the kickpoint of the shaft–lowering it if you cut from the butt end or raising it if you cut from the tip. Even a small adjustment to a putter can cause a significant change in feel. Keep these changes in mind when planning any changes to your club.
How does shortening a golf shaft affect swing weight?
Shortening the shaft can make the golf club less flexible. If you are going to shorten a golf club, there are a few things to keep in mind. The more shaft you cut off, the lighter, more stiff, and effectively flatter the club becomes. For every 1/2 inch you remove, you will lose approximately three swingweight points.
How many swingweight points do you lose when you remove 1/2 inch?
For every 1/2 inch you remove, you will lose approximately three swingweight points. You can readjust the swingweight by adding lead tape to the head of the club. Any amount of cutting will slightly stiffen the club. It will probably go unnoticed if you take 1 inch or less off the club.
What does it mean to tip a golf club?
“Tipping” or “tip trimming ,” as it’s sometimes called, means trimming a club shaft from the clubhead end, not from the grip end where it’s most often cut. ...
What is a parallel shaft?
A parallel shaft is one that has a constant diameter from the tip and up to a specified distance on the shaft. Conversely, a taper tip is as it’s described — the shaft tapers towards the tip. Most new clubs (irons and woods) are designed to accommodate parallel shafts, but can also accommodate a taper shaft using brass adapter shims.
What is a hard step in golf?
A “hard step” is to put a 5-iron shaft into a 4-iron clubhead and so on through the set. This makes the shaft play a little stiffer. A “soft step” is the opposite — it means putting a 3-iron shaft into a 4-iron head (and so on through the set) to make the shaft play a little softer. To receive GOLF’s all-new newsletters, subscribe for free here.
Does tipping affect spin rate?
Lastly, tipping won’t do much to affect spin rates and launch angle — two popular misconceptions when it comes to trimming the lower end of a shaft.
JinxyJ08
Trying to decide between a 63g or 73g whiteboard and am going to play the driver at 44". wondering how much butt cutting takes off weight wise by pulling off a complete inch. anyone have any idea?
jaskanski
Of the overall weight of the shaft? Not a lot. Effect on swingweight? Huge. Cutting 1" off will reduce the swingweight of the club by 6 points. You'll need 12g in the head restore the original swingweight. Deciding between the two different weight categories of the shaft will have no effect whatsoever by cutting 1" off either.
Bobbers
You can mitigate this somewhat by using a WINN Lite grip which is about half the weight of a regular grip.
JinxyJ08
i dont want to know about swing weight since im fully are of what happens there (thanks though because it is important), im talking about actual grams of the shaft. i dont want a mid 50's gram shaft once i lop a bunch off the butt end, I want more of a low/mid 60's gram shaft.
JinxyJ08
See im looking to see IF what my calculations show would be correct. I would have a 66.5g shaft IF the 73g shaft has uniform weight throughout (after i cut the 3.5" off). My biggest concern is that since the whiteboard is "butt soft" its probably a bit less graphite there then the middle and tip. i just don't know!
JinxyJ08
Yess! See that is perfect! Thanks that's what I suspected. That means I'll be now trying to find a 73g whiteboard or a 70g Ahina!
JinxyJ08
Yes the total shaft length will be 42.5" inches which is why a 73g shaft will put me mid/high 60's in grams for shaft weight.
