How to fix a Yamaha G29 golf cart pedal switch problem?
In the G29 Yamaha golf cart, the pedal switch could be the issue. You should check it thoroughly. One quick way to do this is to press the pedal right up to the floor and remove your foot in a quick motion allowing the pedal to spring back to its original position in one stroke. Sometimes, this action can sort out the issue.
What to do if your Yamaha golf cart is not moving?
You can move the belt a little in its groove and do the test again. The starter bushes can also be the reason for the golf cart not moving. Check the controller if you find that your Yamaha golf cart’s solenoid is not clicking after you have installed a new set of batteries.
Why does my Yamaha golf cart controller keep dying?
The controller on a Yamaha golf cart can die when the battery voltage is too high, or because of loose wiring in the charger. The batteries’ voltage: This is one of the primary reasons for your golf cart controller’s death. There are times when the battery voltage is too low or too high.
What kind of battery does a Yamaha G9 golf cart take?
If you have decided to replace the batteries, then Group 24 battery is recommended for the G9 Yamaha golf carts. The solenoid can be checked using an old screwdriver to jump the terminals. Your G9 Yamaha golf cart’s key must be in the start position. If the starter turns when you do this, your solenoid needs to be replaced.
Is there a reset button on Yamaha electric golf cart?
Electric golf cart motors have a reset button on their chassis which is designed to put your motor back into its original factory state.
How do you adjust the throttle on a Yamaha golf cart?
0:005:15Yamaha G29 Drive Golf Cart Governor Adjustment - MORE SPEED!!YouTubeStart of suggested clipEnd of suggested clipItself by tightening this nut down you're putting more pressure on the spring. So that the governorMoreItself by tightening this nut down you're putting more pressure on the spring. So that the governor has to work harder to pull back on the throttle.
How do you take apart a Yamaha golf cart?
0:538:59Yamaha Drive G29 Golf Cart - Body Removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou do have to remove the top or top supports. To be able to remove the front or rear body sectionMoreYou do have to remove the top or top supports. To be able to remove the front or rear body section from the cart.
Where is the speed sensor located on a Yamaha golf cart?
Typically, the speed sensor can be found on the backside of the motor. When removing the speed sensor, unplug all the cables that are on the backside of the motor. To do this, use a socket to take off the connector pigtail. Then, remove its plastic housing over the sensor.
Can you make a Yamaha electric golf cart faster?
Simply put, most types of golf carts are designed to work with a range of different batteries. A new battery will increase a golf cart's motor output. The result of the motor output increase is higher speed. Purchasing new batteries with a higher voltage maximum will increase your golf cart's speed dramatically.
How do you remove the speed limiter on a electric golf cart?
Basically, an electric speed governor can be controlled by a tiny metal rod that's located by the clutch of your golf cart. First things first: The electric speed governor is connected to a cable. You can adjust your speed by rotating the nut in a counterclockwise rotation.
What year is a G29 Yamaha golf cart?
2007In 2007 Yamaha introduced the Yamaha 'Drive' or G29 golf cart which was in production through 2016. The body was still rounded and had the tuning fork logo but the cuves and lines changed as did the seats cupholder and top. The G29A was gas and G29E was electric.
Where is the model number on a Yamaha golf cart?
There serial number on your Yamaha Golf Cart can be located in one of three places:Under the seat where the floor board meets the motor compartment.Under the rear bumper on the frame.Under driver side glove box.
How do you remove the dash on a Yamaha golf cart?
0:337:46Yamaha Drive 2 Golf Cart Body Removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt just has two tabs that hold that down underneath of that is a three millimeter allen head screw.MoreIt just has two tabs that hold that down underneath of that is a three millimeter allen head screw. Then you can just pull up on the dash.
What causes an electric golf cart to run slow?
Low Battery Usually, the most common reason golf carts slow down is when they don't get enough power output from the battery. If the battery pack charge is very low and your cart is out of power, your cart will run slow.
How do you bypass a speed sensor on a golf cart?
The speed sensor on the EZGO golf cart can be bypassed by unplugging it from the speed controller. By disconnecting the J5 pin on the speed controller, this will cause the golf cart to creep along as the controller will go into limp mode.
How do you test a throttle sensor on a golf cart?
Take a digital multimeter and set it to the volts reading. Place the positive probe of the meter on the white wire terminal of the ITS. Release the accelerator pedal slowly. The reading should be in the 0.45V to 0.53V range when the micro-switch gets activated.
How do you adjust the throttle on a gas golf cart?
Pull the spring that is present around the plastic piece located behind the shifter. Spin it until it falls back. Loosen the throttle cable present in the cable box to adjust the extent to which you can take it out of the housing. Press the accelerator so that the golf cart starts up and begins to idle.
How do you adjust the carburetor on a Yamaha golf cart?
How to Adjust Yamaha Golf Cart CarburetorPull out the pilot adjustment screw. ... Rethread the screw back until it's slightly seated.Turn the screw outwards by 1-1/2 turns.Push the throttle stop screw backward until the throttle shaft is closed completely.Turn the screw in by a 1/4 turn.
How do you adjust the governor on a Yamaha 2019 golf cart?
1:294:32Yamaha Drive 2 Quietech Governor Adjustment - GET MORE SPEEDYouTubeStart of suggested clipEnd of suggested clipLeft from where the bottom of the nut is at so to do that i like to use a ratcheting wrench that youMoreLeft from where the bottom of the nut is at so to do that i like to use a ratcheting wrench that you can just put right on the end of that nut. And then just start tightening. It.
How do you adjust the governor on a Yamaha electric golf cart?
1:042:57Yamaha G29/DRIVE Governor Speed Increase | ASK DAVE | Golf Cart ...YouTubeStart of suggested clipEnd of suggested clipAnd locating the governor under the service panel in the rear above the engine. For reference it'sMoreAnd locating the governor under the service panel in the rear above the engine. For reference it's just opposite the driven clutch at the rear of the engine. Compartment.
What does absence of spin mean on Yamaha golf cart?
The absence of a spin in this test could mean your Yamaha golf cart’s battery pack is failing.
How to check solenoid on a G9 golf cart?
The solenoid can be checked using an old screwdriver to jump the terminals. Your G9 Yamaha golf cart’s key must be in the start position. If the starter turns when you do this, your solenoid needs to be replaced. You must be careful while doing this crude test; there could be sparks when the two terminals touch.
Why My Yamaha Golf Cart Solenoid Clicks but Won’t Move?
The main cause of a Yamaha golf cart clicking but not moving, is a faulty controller or solenoid.
Why is my Yamaha golf cart not clicking?
Check the controller if you find that your Yamaha golf cart’s solenoid is not clicking after you have installed a new set of batteries. This can happen and you must first check the controller.
How to connect a battery to a solenoid?
Take a jumper cable and connect them from the positive and negative posts of the battery pack to the two posts on the solenoid that you just disconnected.
Can you repair a pedal switch?
There are ways to repair the pedal switch too, though you can choose to replace it .
How to troubleshoot a 2008 Yamaha golf cart controller?
You can troubleshoot the 2008 Yamaha golf cart controller using the following steps: Press the accelerator and check whether the voltage increases up to the full voltage of the battery. If it does not increase, then there is a problem with the controller or the batteries. Examine the batteries and check if they are dead.
Why is my Yamaha YDRE speed controller not working?
Generally, defective batteries and the motor are major causes of all the problems of a speed controller on a Yamaha YDRE.
Why has my Yamaha golf cart controller just died?
The controller on a Yamaha golf cart can die when the battery voltage is too high , or because of loose wiring in the charger.
How do I test my Yamaha g16 speed controller?
To test the Yamaha g16’s speed controller, check the voltage reading while pressing the accelerator. Test other components such as the batteries, the charger, and the solenoid for their smooth functioning.
What causes a golf cart speed controller to fail?
A faulty solenoid can cause major problems for a golf cart speed controller. Yamaha G22 also faces similar problems like G9 and G16.
What are the problems with a G16 golf cart speed controller?
The most common problems with a G16 golf cart speed controller is overheating and voltage issues.
Why is my Yamaha controller hot?
The primary reason why a Yamaha golf cart controller gets too hot is because of overuse. When the golf cart is used for long periods of time, the controller can start overheating.
