How do you test a club car motor?
13:2337:53Club Car 48 Volt Powerdrive Testing 1995-2013 - YouTubeYouTubeStart of suggested clipEnd of suggested clipPosition place the red positive probe on the speed controller M minus terminal place the blackMorePosition place the red positive probe on the speed controller M minus terminal place the black negative probe on the s2 motor terminal your vom should display continuity.
How do you test a motor with a multimeter?
Set your multimeter to Ohms. Start by completely disconnecting the spindle motor from all power sources. Check each wire, including T1, T2, T3 and the ground wire. If the reading is infinite, your motor should be fine.
How do you troubleshoot an electric golf cart motor?
There are a few simple problems that you can fix yourself that will not necessitate professional maintenance.Test the wall socket where you charge your cart. ... Expose your golf cart batteries. ... Test the batteries for voltage. ... Replace dead batteries. ... Expose the motor for inspection. ... Reset the motor. ... Test the cart.
How do you test a golf cart motor controller?
How to Test a Club Car Golf Cart Speed Controller? The simplest test to ascertain your golf cart controller's performance is to to watch whether it runs when the batteries are fully charged with a slight push of the pedal. If you hear a distinct clicking noise, then your golf cart is running correctly.
How do you tell if a motor is burned out?
When a motor burns out, a short circuit occurs in the windings and the motor ceases to turn. You can test for a short circuit by checking the resistance of the windings with an ohmmeter; a reading of 0 ohms (Ω) indicates a short.
How many ohms should a motor read?
With a multimeter, measure the resistance between motor frame (body) and earth. A good motor should read less than 0.5 ohms. Any value greater 0.5 ohms indicate trouble with the motor.
How do I know if my golf cart motor is bad?
You have enough going on in your life without your golf car refusing to start when you turn the key in the ignition. If your golf car won't start, is slower than it used to be, or is experiencing other technical problems, you could have a bad motor on your hands.
Where is the reset button on an electric golf cart motor?
First, you'll want to reset your motor. It should have a small reset button (Usually it will be red) located near the main battery supply. Hit the reset button and then put the cover back on the motor. The next step would be to recharge your cart and try turning it on again. If it starts up then you're in luck!
How do I know if my golf cart solenoid is bad?
The most common side effect on a gas golf cart is the starter failing to connect, resulting in the engine not turning over and a succession of useless tapping sounds. If your golf cart fails to turn on when you turn the key on, this is the most obvious sign of solenoid failure.
How do I reset my golf cart motor?
Identify your main battery supply (usually the largest battery) on your motor. Check around this supply for a small red button that may or may not be labeled “Reset”. Press and hold this button for a few moments and then release it to reset the motor.
What are the 4 terminals on a golf cart motor?
If you're unsure if it is working, it is simple to test. There are four terminals on a solenoid: usually two large and two small. The small terminals are connected to the battery, and the large terminals are connected to the motor. Disconnect all wires from the two large terminals.
How long do golf cart motors last?
Golf Cart Motor Just like solenoids (mentioned above), your golf cart motor works HARD. When properly taken care of, the typical gas or electric golf cart motor can last many, many years (20 to 30+).
Should a motor have continuity?
Each phase to phase must have a continuity if winding is OK. If any particular phase fails the continuity test, your motor is probably burnt.
How many ohms should a 3 phase motor read?
between 0.3 to 2 ohmsThe reading should be between 0.3 to 2 ohms. If it is 0, there is a short. If it is over 2 ohms or infinite, there is an open. You can also dry the connector and retest to possibly get more accurate results.
How do you ohm out a motor?
Ohming a Single Phase Motor First turn off all power to the equipment, then lock out the disconnect switch and tag it. Measure all power leads inside the unit for any voltage to ground. If no voltage is being read, Then place your meter on a low ohms scale. Determine if motor is single phase, or three phase.
How do you test a motor?
Inspect the Motor Windings With a Multimeter To begin, set the multimeter to read ohms and then test the motor's wires and terminal. You should test the windings for a “short to ground” in the circuit and open or shorts in the windings.
Where is the motor located on a golf cart?
Finally, its time to check the motor itself. This will be located under a panel, usually at the back of the cart. This panel will be held on with four screws, so just make quick work of them with your screwdriver, and set everything aside in a safe place on a towel.
How to check if a battery is working?
Insert the screwdriver into the slot on a clamp and turn counterclockwise to remove it. Repeat this step with the other clamp. Then, test the voltage of the battery by touching each side of the wires to your 12-volt tester. This needs to be done to check all the batteries, as even one not working can cause your motor to malfunction. Don’t forget to remove the clamps before testing the other batteries as well. If at any time the tester shows less than 12 volts, the batteries need to be replaced.
What terminal to test for continuity?
If your motor has an S terminal instead of an F, then test the S-1 to the A-1 terminal to make sure there is no continuity. Then, test the S-2 terminal , to the A-1 terminal for no continuity.
Do golf carts need to be tested?
Owning a golf cart requires a lot of care, including constantly testing the motor. Early detection and troubleshooting motor problems can save you from spending a lot on repairs. So, if you come across problems, confirm that the motor is functioning properly by following the steps below.
How many turns does a regen cart have?
Usually, the wire is rectanular in shape (cross-section). These coils have a much lower number of turns (usually 5 to 15 turns) per field coil. Note: A Regen cart will normally automatically slow down when you hit approximately 15 MPH going down a hill. This is for safety reasons (as not to over-spin the armature).
What is the difference between a series and a shunt motor?
There’s nothing visually different between the two that I know of but a shunt motor has the field windings connected in parallel with the armature .. and a series motor has the field windings connected in series with the armature.
How to reset a golf car?
To reset your golf car’s motor, open the hood to expose your motor and look for the red reset button. Push this button and test out your golf car again. If this hasn’t solved the issue, your motor may be burnt out and will need to be replaced.
Why won't my golf car start?
If your batteries are charged and in working condition, but your car still won’t start, check its solenoid. A solenoid is an electromagnetic coil of wire that transmits energy from your car’s battery to its motor to help it start. Every time you start your golf car, you should hear the click of the solenoid. If you don’t hear it, you probably have an issue with your solenoid. If you suspect an issue with the solenoid, take your car to a repair shop to have it repaired or replaced.
What to do if your car won't start?
If your car still won’t start or you notice any issues with acceleration, it’s time to check the potentiometer. The potentiometer sends an electric signal from the accelerator pedal to the speed controller, allowing the car to accelerate properly. Inspect the potentiometer and then test it out—if you discover any issues, have it repaired or replaced.
