Golf-FAQ.com

how tight should a golf cart drive belt be

by Lorena Mayert Published 2 years ago Updated 2 years ago
image

The drive belt should not be too tight. If it’s too tight it can risk wearing off faster and it’s also harder to shift gears. To check if your drive belt is set just right make sure your golf cart is turned off then check the drive belt by pressing it down between the two clutches with your finger. If it deflects less than 1.5” it’s too tight.

Full Answer

How tight should the belt be on a club car golf cart?

How Tight Should the Drive Belt be in a Club Car Golf Cart? The rule of thumb is that the drive belt must neither be too tight nor too loose. If the drive belt in a Club Car golf cart is loose then you won’t get the required speed while driving. If the belt is too tight then your starter will be under strain and this should be avoided.

How to stop a drive belt from slipping on a golf cart?

Sep 01, 2021 · Reasonable pressure is generally accepted as about 20 lbs. of pressure for each inch of belt width. Our belt is a lot closer to ½ inch, so we would only apply about 10 lbs. of pressure. So, if we push with 10 lbs. of pressure in the center of the span, we should be able to get the belt to flex a little less than a quarter of an inch. WOW!

How do I know if my golf cart drive belt is bad?

The drive belt should not be too tight. If it’s too tight it can risk wearing off faster and it’s also harder to shift gears. To check if your drive belt is set just right make sure your golf cart is turned off then check the drive belt by pressing it down between the two clutches with your finger. If it deflects less than 1.5” it’s too tight.

How to adjust the drive belt on an EZGO golf cart?

May 19, 2010 · The S/G belt needs to be tight in order to crank the motor without slipping whereas the drive belt is a little slack in order to give a smooth transition from stopped to rolling. Think of it as a poor mans torque converter ... Lifted Golf Carts: how tight... Gas EZGO: Is the belt too tight? Gas Club Car: All times are GMT -5. The time now is 04 ...

image

How do you tighten the belt on a Club Car golf cart?

Slide the old drive belt off the front drive clutch pulley, and then the rear clutch pulley. Slip the new belt around the golf cart's clutch pulley, and then stretch it out over the front pulley. Pull the front pulley forward slightly to increase the belt tension, and then tighten the tension bolt with the wrench.Sep 19, 2011

Can you tighten a golf cart drive belt?

And EZGO is no different – there are no screws, knobs, or any other type of adjustment item that you can use to tighten up your belt. Once the belt is one, it has the same tightness and can only be changed if you swap the belt for another one either the proper length and width for your specific cart engine.

How can I make my drive belt tighter?

Part of a video titled HOW TO TIGHTEN A DRIVE BELT PERFECTLY EVERYTIME - YouTube
0:48
4:48
Between two pulleys and you're going to tighten it until that part of the belt can only turn 90MoreBetween two pulleys and you're going to tighten it until that part of the belt can only turn 90 degrees halfway.

How do you tighten the belt on a club car starter?

Part of a video titled How to Replace your Starter Generator Belt on the 2004 Club ...
9:17
11:52
Basically we're just going to pull. Up. Keep it keep it tight have a friend hold it. And then we'reMoreBasically we're just going to pull. Up. Keep it keep it tight have a friend hold it. And then we're going to get to the back of this belt here again. And tighten the nut on the back of the adjusting.

How do you know if your golf cart clutch is bad?

What Kinds of Problems Can a Golf Cart Clutch Have?
  1. A sudden inability to maintain even slow speeds when heading uphill or changing elevation.
  2. Slowing down to a crawl, then speeding up, then slowing again, seemingly without reason.
  3. Jolting during startup.
  4. A 'cranking' sound when starting up the golf cart.
May 11, 2017

How do you measure a torque converter belt?

Simply take a measuring tape and hold it against the outer plate of the pulley. Measure from one side of the plate to the opposite side. If you're running a standard torque converter the diameter will either be 6-inches, 7-inches, 7.5-inches or 8.5-inches.

How tight should a pulley belt be?

Part of a video titled Belt tension trick - YouTube
0:31
1:54
If it goes to 90 degrees. But doesn't want to go any further than that then you've got good tensionMoreIf it goes to 90 degrees. But doesn't want to go any further than that then you've got good tension on that belt. When should you replace your belt.

How do you know if your drive belt is loose?

A loose drive belt will often be noisy, squeaking a bit, or emitting a high-pitched squeal. The most obvious sign of a loose drive belt, though, is in its appearance and tension. A loose belt, simply stated, looks and feels loose.Nov 30, 2015

How tight should tensioner pulley be?

The required measure of tension in the serpentine belt is that it should not deflect more than ½ inch when twisted either way from the middle. If twisted more, the belt is loose, and if twisted less, the belt is too tight. Either of the positions does not work for the vehicle.

How does the clutch work on a golf cart?

Part of a video titled How a golf cart CVT slip drive clutch works - YouTube
0:46
3:28
And the rear drive clutch actually separates it widens causing the belt to drop down into the clutchMoreAnd the rear drive clutch actually separates it widens causing the belt to drop down into the clutch.

How do you put a belt on a golf cart?

Part of a video titled Changing the Drive Belt and Starter Generator Belt 2008 EZGO TXT
2:47
5:57
Just. First put the belts on and then tilt the starter generator as far as you can and tighten thatMoreJust. First put the belts on and then tilt the starter generator as far as you can and tighten that nut up. By hand first and then use the wrench to get it a little bit. Tighter.

Is the Ping G25 adjustable?

Is the Ping G25 driver adjustable? The Ping G25 driver is adjustable. It’s possible to do four adjustments using the hosel adapter of the driver apart from the stated loft setting and...

Is the Taylormade M4 driver adjustable?

Is the TaylorMade M4 driver adjustable? Yes, the TaylorMade M4 driver is adjustable. It’s possible to have twelve different options for the loft, lie angle and face angle, including the standard...

Step 1 – Determine Belt Type

The first thing that you’ll need to do is to identify which type of drive belt you need for your torque converter. When it comes to go-kart belts, there are two types. On the one hand, you have symmetrical belts, and on the other hand you have asymmetrical belts.

Step 2 – Measure Driven Pulley Diameter

The next measurement you’ll need is the diameter of the driven pulley. A torque converter has two pulleys. The pulley that is attached to the crankshaft is called the driver pulley, as it drives the belt through the rotation of the crankshaft.

Step 3 – Measure Center Distance

The third measurement you’ll need in order to measure the go-kart belt size is the distance between the driver and the driven pulley. This distance is also known as the center distance. This distance is measured from the center of the crankshaft to the center of the jackshaft.

Step 4 – Check Measurement Against the Belt Size Chart

Now that you’ve identified the belt type, driven pulley diameter, and center distance you can easily determine which belt size you need for your go-kart torque converter. Head over to the go-kart belt size chart that I created.

What are the Available Comet Belts Series and Sizes

There are a few go-kart belt manufacturers, but the most common brand is Comet. If you’re buying a go-kart belt you’ll most commonly see them refer to the Comet equivalent so that you can always ensure that you’ve got the right size.

How Tight Should Go-Kart Belt Be?

When it comes to the fitting, you should always stick with the manufacturer’s recommended sizing. If the center distance of your torque converter can’t be found on the belt chart, ensure that you get the one that is closest to the measurements. In the worst case, a looser belt is better than a belt that is too tight.

How to Fix a Go-Kart Belt That Keeps Jerking?

If you’re experiencing jerking when accelerating, there is a high chance that it may be because of your torque converter. You should immediately check the wear on your go-kart belt. If your belt is not lubricated properly, is too loose or is too worn, it may cause a jerky or even sluggish acceleration.

image

Step 1 – Determine Belt Type

Image
The first thing that you’ll need to do is to identify which type of drive belt you need for your torque converter. When it comes to go-kart belts, there are two types. On the one hand, you have symmetrical belts, and on the other hand you have asymmetrical belts. The type of belt that you require for your go-kart depends on t…
See more on gokartguide.com

Step 2 – Measure Driven Pulley Diameter

  • The next measurement you’ll need is the diameter of the driven pulley. A torque converter has two pulleys. The pulley that is attached to the crankshaft is called the driver pulley, as it drives the belt through the rotation of the crankshaft. The other pulley that is on the opposite end of the torque converter is called the driven pulley, as it’s driven by the belt. This pulley is connected to the jack…
See more on gokartguide.com

Step 3 – Measure Center Distance

  • The third measurement you’ll need in order to measure the go-kart belt size is the distance between the driver and the driven pulley. This distance is also known as the center distance. This distance is measured from the center of the crankshaft to the center of the jackshaft. Measuring the center distance is very easy, simply hold a measuring tape...
See more on gokartguide.com

Step 4 – Check Measurement Against The Belt Size Chart

  • Now that you’ve identified the belt type, driven pulley diameter, and center distance you can easily determine which belt size you need for your go-kart torque converter. Head over to the go-kart belt size chartthat I created. I suggest that you keep the belt chart open in a separate window and continue reading, as I will now teach you how to check for the right belt size. Let’s work with the …
See more on gokartguide.com

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9