Fit the Replacement Bulb: Apply a bit of dielectric grease to the end of your replacement brake light bulb to prevent future rust and corrosion and make it easy to remove when it too must be replaced. You can then put the new bulb in place, reattach the tailgate housing, and continue driving safely.
How do the brake lights work on a 2000 Volkswagen Golf?
The brake lights on your 2000 Volkswagen Golf illuminate when you hit the brake pedal and help prevent you from being rear ended by the cars behind you. Brake light bulbs grow dimmer over time and eventually burn out. This video shows you how to change the brake lights on your 2000 Volkswagen Golf.
Should I change the lights on my Volkswagen Golf?
Not only will the lights on your Golf be brighter, you decrease the likelihood you will need to change any of the bulbs again in the near future. A burnt out bulb in the taillight cluster of your Golf is an excuse for a police officer to pull you over. Check your bulbs frequently and change burnt bulbs promptly.
Should I change the tail light bulbs on my golf?
Not only will the lights on your Golf be brighter, you decrease the likelihood you will need to change any of the bulbs again in the near future. A burnt out bulb in the taillight cluster of your Golf is an excuse for a police officer to pull you over.
How do you change a brake light on a mk4 Golf?
0:071:23Replacing VW Golf rear Brake light bulb - How to Remove and Fit New ...YouTubeStart of suggested clipEnd of suggested clipEither side of the light cluster or the bulk where inside there were two clips you push those in itMoreEither side of the light cluster or the bulk where inside there were two clips you push those in it allows you to just move out the bulb holder so that you can get access.
Can I change my brake lights myself?
Changing a faulty brake light is something anyone can learn to do. A replacement bulb costs about $10, and replacing it on your own will save about $20 in labor and the time it takes to travel to the shop and wait for the work to be done.
How do you remove a brake light to replace?
How to replace or repair tail lightsLocate the faulty bulb.Remove fasteners from lining. ... Remove the bulb assembly from the lens with a twist.Pull the bulb out of the socket.Insert the new bulb into the socket.Re-install the bulb assembly into the tail light lens. ... Reinstall trunk lining.
How do you change a brake light switch on a VW?
2:183:40VW Mk4 Replace Brake Light Switch - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith the panel out of the way the brake lights which can be seen at the top of the brake pedal toMoreWith the panel out of the way the brake lights which can be seen at the top of the brake pedal to remove the switch will just grab the switch with our hand and rotate it counterclockwise.
How long does it take to replace a brake light?
Be Prepared Fortunately, tail light bulb replacement isn't difficult and shouldn't take you more than 45 minutes to an hour to complete. Be aware that newer models may be a little more complicated than older ones, as there will be more wires to disconnect.
Is the tail light the same as the brake light?
Tail lights are engaged when the you turn on your headlights or when your parking brake is on, whereas the brake lights will light up immediately when you apply pressure to the brakes. On most vehicles, the tail lights are red and the brake lights are a more luminous red.
How do you remove a tail light?
Before you begin - or if you have any questions about your specific vehicle - we always recommend taking a look at your service manual.Step 1: Open trunk or tailgate. ... Step 2: Pull tail lamp assembly out (if needed) ... Step 3: Pull bulb out. ... Step 4: Add bulb grease, put new bulb in. ... Step 5: Reattach assembly (if needed)More items...
How can I check my brake lights by myself?
0:161:27How to check brake lights by yourself - YouTubeYouTubeStart of suggested clipEnd of suggested clipWithout having to remove them using a multimeter. You could of course use your mobile phone to filmMoreWithout having to remove them using a multimeter. You could of course use your mobile phone to film the back of the car or van.
How do you remove a tail light assembly?
Open the trunk of your vehicle and locate the back of the tail light assembly. Disconnect the wiring harness from the back of the tail light assembly. Remove the tail light assembly mounting screws or nuts. Push the tail light assembly out from behind.
Where is the brake light switch located?
In most cars, the brake light switch is installed right above the brake pedal. Inside, it has a one- or two-way electric switch.
How does a VW brake light switch work?
0:1211:14Instant Brake Lights for Classic VW's - YouTubeYouTubeStart of suggested clipEnd of suggested clipSomething that is new its revolutionary it instantly. Now as soon as you touch the brake. ItMoreSomething that is new its revolutionary it instantly. Now as soon as you touch the brake. It instantly activates the brake stoplight. System on your car.
Can a bad brake light switch symptoms?
One of the symptoms commonly associated with a bad brake light switch are brake lights that stay on at all times. If the brake light switch shorts internally it may cause the brake lights to stay illuminated, even when the pedal is not being pressed.
Volkswagen Golf Brake Warning Light Causes
The brake warning light indicates that your Golf has detected that one of its major brake components has failed, typically detected through a loss of pressure. You’ll feel a loss of pressure that manifests itself in the form of a “mushy” brake pedal.
Conclusion
If your Volkswagen Golf’s brake warning light is on, and you’ve checked the emergency brake, you’ll need to look for a leak in the lines, calipers, wheel cylinders, master cylinder, etc. Good luck diagnosing the issue. If there is anything that you would like to add, please leave a comment below.