Mark the extension for the added length desired. Secure the shaft extension in the vise. Cut the extension to the desired length with a hacksaw and clean the residual material and smooth the edge from the cut with a knife or a file. Mix a small amount of epoxy and apply it to the part of the extension that fits inside the shaft.
How long can you extend a golf club?
The maximum length you can add is up to an inch and a half and not over cause there is a risk of compromising the integrity of the shaft, which can make it break easily. An extension can be used in lengthening the golf club where it is fitted in the butt end of the shaft, and once dried, the golf club can be cut to the preferred length.
How do you measure a golf club?
The hosel is the portion of the club where the clubhead is connected to the shaft. The straight edge should be pressed as close as possible to the shaft. Now, read the measurement at the bottom of the grip cap. This should tell you the length of the shaft. Iron: The one iron club is a little over forty inches in length.
Can You align the length of your golf clubs?
Altering the length of your golf club could seriously mess with the following: Distance: Quite simply, the maximum distance that you can drive the ball. Since clubs are designed within half an inch of each other, the adjustments are small, but the overall force changes dramatically.
What is the maximum length of a golf club?
The United States Golf Agency (USGA) limits the maximum length of golf clubs. The minimum length for all the golf clubs, including putters, is 18 inches. The maximum length for all golf clubs except the putters is 48 inches. The putters do not have the maximum length limit.
Can you add length to existing golf clubs?
There are two ways to lengthen your shafts. You may add extenders to your existing shafts or you may replace your existing shafts with longer ones. The effects can be very different. Tom Wishon has written extensively about the effects of changing shafts in "The Golfsmith Practical Clubfitting Program" guide.
How much does it cost to add length to golf clubs?
How much does it cost to lengthen golf clubs? On average, it will cost $8-9 per club plus the cost of a new grip to lengthen your clubs. If you're looking to save your old grips, you'll avoid the cost of new grips, but you'll have to pay a save grip fee of around $10 per club.
Can I adjust the length of my golf clubs?
You can buy extension pieces or cut one yourself from an old shaft, using the same cutting techniques that you did for trimming a shaft from the butt end. Use sandpaper to lightly abrade the edge of the extension piece that will attach to the new shaft, then apply epoxy glue to fasten the piece to the shaft.
Should I add length to my irons?
Sometimes a golfer's height and arm length will negate each other and a standard length is the best option. As length is increased, so is the weight. Increasing the length also changes shaft flex. For every 1" added, the shaft becomes one flex softer; likewise, a shorter shaft plays stiffer.
How do I know if my golf clubs are too short?
6 Signs Your Golf Clubs are Too ShortYou need to bend too much at the waist before swinging.You also have to bend your knees pre-swing.You keep hitting the ball with the golf club's heel.The swing path is in to out.The tempo is too quick.The ball tends to veer off to the right.
Is a club fitting worth it?
Is it worth getting custom fit golf clubs? The simple answer is yes, it's definitely worth getting custom fit golf clubs. If you were to look at the back of a typical set of off the shelf clubs, they would usually have various markings on them as well as loft and lie angles.
How long should my golf clubs be for my height?
Using the ratio of every 6" of height there should be a 1" change in length then there should be a 1 ½" difference between their 5-irons. For example, recommend 36.5" for the lady and 38" for the man (or 36.75" / 38.25").
How long should my driver be for my height?
Tony Finau is one of the tallest golfers on the PGA Tour at 6'4″, and his driver's length is usually around 45 inches. Both Finau and Fowler are two of the longest drivers on the PGA Tour....Driver Shaft Length Based Solely on Height.Height (feet/inches)Driver Shaft Length5'0″-5'2″44.5″4'10”-5'0″44″< 4'10”43″7 more rows•May 9, 2021
How much does it cost to cut golf clubs?
Any amount of cutting will slightly stiffen the club. It will probably go unnoticed if you take 1 inch or less off the club. Taking 2 inches off will change the flex of the club. If you are shortening irons, every 1 inch you shorten the club will make the iron effectively play 2 degrees flatter.
How do I lengthen my irons?
7:4711:02How to ADD Extensions To Golf Clubs - Start to Finish! - YouTubeYouTubeStart of suggested clipEnd of suggested clipI go a half inch long is because I like to tuck a little bit of the excess into the butt end of theMoreI go a half inch long is because I like to tuck a little bit of the excess into the butt end of the club. I use the narrow grip tape. So you're gonna have to use two pieces.
How long should my irons be for 6 1?
1. Measure Your Overall Height (i.e. “static” fitting)OVERALL HEIGHTGOLF CLUB LENGTH ADJUSTMENTS5'7″ to 6'1″standard length in inches6'1″ to 6'2″plus 1/4″6'2″ to 6'4″plus 1/2″6'4″ to 6'6″plus 1″7 more rows
How do you add 1/2 on a golf club?
5:529:01Extending Golf Shafts 1/2 Inch | How to at home! | Simple - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then simply take your golf club and the extension. And insert one into the other. And twist itMoreAnd then simply take your golf club and the extension. And insert one into the other. And twist it down until you have no gift between the shaft and the extension itself and that will then rest.
Why do golf clubs change length?
Changing your golf club's length also changes the club's playing characteristics -- which is the reason golfers decide to shorten or lengthen a club. On the other hand, maybe you received a driver as a gift that's a bit too long, or you found an otherwise perfect wedge at a garage sale that doesn't quite fit.
How to remove a clubhead?
Use a shaft extracting machine to remove the clubhead. Heat the hosel to melt the glue before pulling off the clubhead. Trim a graphite or steel shaft using a hacksaw, cutoff wheel or chop saw. You can also use a tubing cutter on a steel shaft. Put a new grip on the club if you've trimmed from the butt end.
How to remove grip from butt?
Remove the grip with a blade if you're cutting from the butt end. Use a hooked blade on a graphite club to avoid damaging the shaft. To trim from the tip, heat the ferrule with a heat gun to loosen the glue, then cut the ferrule off the shaft. Use a shaft extracting machine to remove the clubhead. Heat the hosel to melt ...
Does lengthening a golf club make it faster?
Lengthening Effects. Lengthening a club gives you a longer swing and, potentially, a faster swing speed. The increased speed will translate into more distance if you hit the ball squarely. But the added weight may cost you some control and make it more difficult to hit the club's sweet spot. Longer shafts also become more flexible.
Does trimming the butt end of a golf club make the shaft stiffer?
If you trim the club from its butt end you'll also increase the shaft's flexibility, because the narrower, more flexible portion now makes up a greater percentage of the shaft's overall length. By the same logic, trimming the tip makes a shaft stiffer, but the club's most flexible area is reduced.
How to Figure Out the Ideal Club Length
You will find that the vast majority of players start off by figuring out their height and wrist to floor measurement when it comes to buying the correct golf club length.
Should I Get a Custom Fit?
A custom fit can be great, but you need to remember some things. If you are ordering a club that is custom to you, the club shaft is going to be made in such a way that the flex is going to match the club length.
Conclusion
As we’ve covered above, getting the right fitting for your golf clubs is essential in making sure that you get the best results from your golf game. Hopefully the above guide has helped you to find out what the correct golf length should be for your height.
Series Navigation
Extending a golf shaft is a useful technique to have if you are buying used clubs, or if you are experimenting with different club lengths. If you know how to cut a golf shaft or how to extend it, you don’t ever have to worry about purchasing the correct length of clubs on Ebay or other used club marketplaces.
Materials Needed
Extension (You could also use an old golf shaft) Make sure you purchase the right size extension. You need to know the “butt diameter” of the shaft that you are extending, and purchase the extension that matches. Here is a database of shafts.
About the Author: Zach Gollwitzer
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
What is the best way to get accurate golf clubs?
Club fitting is the best way to get accurate golf clubs, cause there is no standard lie angle that you can find in any golf store, and you need the fitting, so it will be according to your build, swing type, and preference.
Where is the extension on a golf club?
An extension can be used in lengthening the golf club where it is fitted in the butt end of the shaft , and once dried, the golf club can be cut to the preferred length.
What does it mean when a golf club is too upright?
A club that is too upright every time you swing means that the heel of the clubhead is lower than that of the toe. The tendency here is for the ball to hook, especially for those who are right-handed golfer where the curving of the shot, often takes place. An upright lie angle is more common because the golfers who are just beginning in ...
Why does my golf club slice?
There is a risk of slicing the ball when your angle is too flat. This means that the angle between the shaft and the ground is smaller. Once your club is too flat for your swing, the toe of your golf club will have a lower range than the heel when it should be leveled. Slicing happens because of such reasons.
How to increase swing weight?
Swingweight can easily be increased by using lead tape placed at the clubhead. Lengthening a club softens the shaft a fraction while increasing the swing weight of the club. Each time you add length like half an inch will also add three swing weight points.
How does a half inch length change affect a golf swing?
Every half-inch length change alters the lie by a degree. There will be an alteration in the way you grip the club, change in your positioning or posture while taking a swing, you may need to bend it a little to drop your hands a bit, or you may stand more upright to make up for the change in distance. Since there will be changes in the length of ...
How to get the right lie in golf?
To get the right lie, make sure that whenever you change the length of the golf club, you are also trying out the clubs to match your swing. Pro-golf shops can adjust some clubs to match it according to your need.
How many inches to a standard length golf club?
Six feet, five inches-add one and a half inches to the standard length of the club. Six feet, three inches to six feet, five inches-add one inch to the standard length of the club. Six feet to six feet, three inches-add half an inch to the standard length of the club.
How to tell if a golf club is too long?
Below you’ll find common signs that indicate the clubs you’re using are too long: 1 You have to stand up almost completely straight. 2 You’re unable to move your lower body using proper swinging mechanics 3 The ball often flies off to the left and too high. 4 The club’s shaft feels very weak 5 You’re constantly hitting the ball with the toe of the golf club.
How long is a standard iron club?
Standard Club Sizes. Iron: The one iron club is a little over forty inches in length. Each iron falls half an inch with each size until you reach the nine iron which measures in at a little over thirty-six inches. Differences in irons can also occur due to shaft material.
How long is a golf driver?
On average, most golfers use a driver that’s forty-four inches in length, however, a club shaft up to forty-eight inches in allowed for competitions.
How tall should a golf iron be?
Height Recommendations for Irons. Here you’ll find the standard recommended measurements for golf clubs based on height: Six feet, six inches and taller-add two inches to the standard length of the club. Six feet, five inches-add one and a half inches to the standard length of the club.
How long is a three wood putter?
Putter: The standard length of a putter is thirty-four inches, however, the length of a putter is measured much differently than irons. It often depends on the putter’s construction.
Do beginners need to size their golf clubs?
These are questions many newbies have but don’t know the answer to. Beginners usually struggle with sizing their golf clubs correctly. Unfortunately, when it comes to clubs, size is very important. In fact, the right size of clubs can significantly improve your game, while the wrong size of clubs can negatively impact your performance, ...
How does a lengthened golf club work?
A longer distance can be achieved with a lengthened club if you have the ability to swing it with the same force and speed that you did with a shorter club . This increases the ball’s velocity upon impact, and you can hit it farther. Flex: The flex of the shaft will be altered. This happens for a few reasons.
What happens if you play too long in a golf club?
If the club is too long for you, then you’re spending extra time during ramp up which is the amount of time spent during your initial downswing. You want a balance between your abilities, ramp up, and momentum while cutting through the wind with as little resistance as possible.
Why are golf clubs made the way they are?
The reason clubs are made the way they are is to gather momentum as you swing down. If your club is too short, you’re going to build momentum while having resistance, meaning you will push too hard against the wind and not just swing naturally. There’s not enough weight to the club.
What happens if your woods aren't longer?
If your woods didn’t have the length that they do, and they were shorter, you’d be sending your ball almost straight up and they wouldn’t close much of a distance. It’s not always about the angling of the golf club head; sometimes it’s about the length and force to make it meet the ball.
Why do you have to swoop on your golf club?
Because the club is longer, you have to swoop on your downward swing, causing the force of your wood – if you’ve hit it correctly – to be applied to the bottom of the ball and send it upwards. A wood without enough length just doesn’t cut it. You’d be sending the ball higher but with almost no distance.
When shortening a golf club, do you have to remove the crown?
When you shorten a golf club, you have to remove the crown, and safely disconnect the shaft from the head.
Why did Lars start golfing?
Father of six and long-time golfer, Lars started golfing because of a summer job when he was nineteen, where he caddied for a Virginia state official. From that moment on, he fell in love with the sport, and made it a core staple in his life. Thirty-five years later, with thousands of games under his belt, he’s here to teach you the fundamentals and master techniques of golf, while recommending proper golfing gear and equipment for every step in your journey.
How to measure golf club length?
Important Information before we know “How to Measure the Golf Club Length.” 1 The standard irons designed for women are usually an inch shorter than the standard irons designed for men. 2 The United States Golf Agency (USGA) limits the maximum length of golf clubs. 3 The minimum length for all the golf clubs, including putters, is 18 inches. 4 The maximum length for all golf clubs except the putters is 48 inches. 5 The putters do not have the maximum length limit. 6 The shaft length has everything to do with the length of the golf clubs. The longer shaft does mean longer golf club length. 7 A golfer uses woods, hybrids, and irons for different types of shots. It is the reason why their golf club is mostly empowered with a mix of these three.
What is the minimum length of a golf club?
The minimum length for all the golf clubs, including putters, is 18 inches. The maximum length for all golf clubs except the putters is 48 inches. The putters do not have the maximum length limit. The shaft length has everything to do with the length of the golf clubs. The longer shaft does mean longer golf club length.
How long should a golf shaft be?
The chart recommends + 0.25 inches. It means that your golf shaft has to be made 0.25 inches longer than the standard length. Similarly, if your height is 66“ and the wrist to floor distance is 31.5 inches, the chart recommends – 0.75 inches.
What does a longer shaft mean?
The longer shaft does mean longer golf club length. A golfer uses woods, hybrids, and irons for different types of shots. It is the reason why their golf club is mostly empowered with a mix of these three. Therefore we must know about the standard length of the woods, and irons. Let’s first discuss the standard lengths of woods.
How to measure club size with LDA?
The following are steps of measuring the club size using the LDA method. Step 1. First, put the shaft against the wall so that the toe of the driver is placed on the ground. Step 2.
Where is the shaft of a putter located?
It is because the shaft of the putter is mostly installed in the heel. The shaft placement is either near the heel or in the center of the club head. Therefore, it is essential to measure the putter differently. The method of measuring the length of a putter is described in the following steps. Step 1.
What is the USGA method?
Method 5: The United States Golf Association (USGA) Method. The USGA method is part of the rule book’s method: “Rules of Golf.”. In it, an apparatus containing an angle iron is used. The angle iron forms a 60-degree angle from the horizontal, and it is also used to stop /hold the iron.
