How to Adjust the Governor on a Gas E-Z-Go Golf Cart
- Locate the governor arm mounted on top of the rear axle case underneath the cart. ...
- Loosen the adjusting locknut on the end of the governor spring. Rotate the locknut to expand or compress the spring until its length is 2 1/2 inches.
- Retighten the adjusting locknut.
- Road test the cart by timing it over a course of known length at full speed to verify that the governor is controlling the speed within factory specifications.
How do you bypass the governor on an EZGO golf cart?
You can bypass the governor connection in an EZGO or Yamaha G1 golf cart as given below. Remove the cable connecting the carburetor and the governor. Disconnect the connection between the gas pedal and the governor. Connect the gas pedal directly to the carburetor opening.
How do you adjust the speed on an EZ GO golf cart?
Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.
How do you adjust the governor on a golf cart?
Loosen the adjusting locknut on the end of the governor spring. Rotate the locknut to expand or compress the spring until its length is 2 1/2 inches. Retighten the adjusting locknut. Road test the cart by timing it over a course of known length at full speed to verify that the governor is controlling the speed within factory specifications.
Can you adjust the governor on an EZ GO spark plug?
Many manufacturers, including EZ Go, do not want consumers tampering with their engines, and have thus hidden the governors in the spark plug ignition. This is very difficult to adjust without ruining the engine, and should be left to trained professionals. How can I stop the choke cable from getting hot on my EZ-GO golf cart?
How do you adjust the speed limiter on a EZ Go golf cart?
Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.
How do you adjust the governor on a 2 stroke EZ Go golf cart?
How to Adjust the Governor on a Gas E-Z-Go Golf CartLocate the governor arm mounted on top of the rear axle case underneath the cart. ... Loosen the adjusting locknut on the end of the governor spring. ... Retighten the adjusting locknut.More items...
How do you adjust the governor on a golf cart?
Adjusting an EZ-GO Golf Cart GovernorStep 1 - First, lift the seat of your engine to reveal seat cousins. ... Step 2 - Remove the seat cushions over your motor. ... Step 3 - Remove the black plastic cover to expose the motor. ... Step 4 - Loosen the smaller one and tighten the larger one to increase your cart's speed.More items...•
How do I turn off the governor on my EZ GO?
0:000:46How to remove governor on a Club Car golf cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou open up this box lap. Here. It looks up look inside. There's 12 cable down right here this leverMoreYou open up this box lap. Here. It looks up look inside. There's 12 cable down right here this lever you want to lift up and Bend and that pulls on the cable a little more.
Where is the speed controller on an ezgo golf cart?
These speed controllers are located under the EZGO cart seat. Check the speed controller's attachment near the carburetor.
How do I speed up my EZ GO TXT electric golf cart?
You can make your EZGO golf cart go much faster by adding more torque, upgrading the motor of or increasing the voltage of the batteries.Add more torque.Upgrade the motor.Increase the battery voltage.Decrease the load.
How do I adjust my EZ GO carburetor?
2 Cycle engine: The adjustment screw is on the side of the carburetor and is parallel to the ground. You can identify it by the lock nut at the base of the screw. Loosen this and turn the screw all the way into a soft seat, then back it out one and a half (1-1/2) turns.
What does removing the governor do?
Removing the governor will increase the maximum rpm of the engine, but the internal parts of the Predator 212 are designed for 3600 rpm. Generally, this isn't an issue with just the governor removal, the internal parts can usually withstand 5000 rpm without breaking apart (unless you go full throttle for too long).
Where is the governor on a golf cart?
0:101:28Where Is a Golf Cart Governor Located? - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell a golf cart's governor located is actually down in the motor. Compartment. Some of them theseMoreWell a golf cart's governor located is actually down in the motor. Compartment. Some of them these electric ones nowadays. Actually the governor isn't a true governor. It is a control speed.
How fast can a golf cart go without a governor?
A typical electric cart without an upgraded speed control tops out around 12 mph.
How can I make my electric golf cart go faster without upgrading?
How to Make an Electric Golf Cart Faster Without UpgradesWash Your Cart Properly. ... Inspect the Batteries. ... Refill the Battery Water. ... Check the Gas Pedal and Linkage. ... Measure the Tire Pressure. ... Charge Up Your Battery Unit. ... Lighten Up Your Cart's Weight.
How do you make a gas golf cart go faster?
How to Make Your Gas-Powdered Golf Cart Faster [Updated, 2022]1 Use A Better Golf Cart Battery.2 Increase Torque.3 Upgrade the Golf Cart Motor.4 Install a Torque Converter.5 Install a Higher-Performance Clutch.6 Tweak The Governor.7 Install A Cold Air Intake.8 Get Bigger Golf Cart Tires.More items...
How fast is an EZGO golf cart?
The top speed of an EZGO golf cart is usually 19.9mph and the average speed is 14mph to 15mph. With governor adjustment, the EZGO cart can go faster by 5 to 10mph.
What is a golf cart governor?
A golf cart governor is a mechanical device that helps in controlling the maximum speed of the cart when it moves on flat ground. This device prevents the engine RPMs from increasing beyond the recommended specifications.
How to start a golf cart with a gas pedal?
Locate the gas pedal that is fitted to the governor and remove the connection. Re-route the gas pedal to the carburetor. Remove the bolt present on the shaft of the gas pedal. Slide the shaft upwards so that the gas pedal has more play. Tighten the bolt and start the golf cart.
How to change the speed of a golf cart?
Locate the spring on the differential or carburetor that helps in changing the cart speed by adjusting its tension. Increase the length of the cable that is fitted on to the body of the throttle and clutch of the two-stroke engine.
How to ride a golf cart at full speed?
Ride the cart at full speed over a course of known length. This will ensure that the governor controls the speed of the cart within factory specifications. Fasten the black plastic cover and put the seat back in place. Take care when tightening the nut. The more you tighten, the faster your cart will go.
Where is the governor arm on a golf cart?
Locate the governor arm of the golf cart. This is mounted above the rear axle housing and under the cart. Depending on the cart model, there may be a protection plate above the governor.
Can you remove a golf cart governor?
It doesn’t take much time or skill to remove a golf cart governor. With some basic mechanical expertise and general-purpose tools, you can do this yourself. The process is more or less the same in all golf carts.
