Install the shift cable end of the shift cable to the transmission shift lever stud ball. Install the retainer to the shift cable and transmission bracket. Feed the shift cable through the floor panel. Lower the vehicle. Adjustment Procedure Ensure that the shift cable is not restricted. Place the shift lever into the NEUTRAL position.
Full Answer
How do you adjust the throttle cable on an EZGO golf cart?
How do you adjust the throttle cable on an EZGO golf cart? Close the carburetor throttle plate.. Rotate the governor arm in a counter-clockwise direction.. Keep the cable inside the throttle cable bracket that is fitted on the rear axle.. Make sure that the governor and carburetor are seated with ...
How do I adjust the shift cable on the E-Z-GO TXT?
The adjuster has to be in the neutral position while making this change in the cable’s position. There’s very little available by way of printed literature on the step-by-step method of adjusting the shift cable on the E-Z-GO TXT model.
How can I Make my EZ GO golf cart go faster?
1 Gasoline Engines. One way to increase the speed of a gasoline-powered EZ Go golf cart is to add an octane booster when you fill the gas tank. 2 Electric Motors. Looking at the specifications for EZ Go electric golf carts, you notice a cart with a 36-volt motor is capable of 12 to 14 mph top speed. 3 Speed Controllers. ... 4 Gearing and Chips. ...
Can you adjust the governor on an EZ GO spark plug?
Many manufacturers, including EZ Go, do not want consumers tampering with their engines, and have thus hidden the governors in the spark plug ignition. This is very difficult to adjust without ruining the engine, and should be left to trained professionals. How can I stop the choke cable from getting hot on my EZ-GO golf cart?
How do you adjust the forward and reverse cables on a EZGO golf cart?
You can do the shift cable adjustment, with the shift lever in the forward position and then again changing it to the reverse position.
How do you adjust the throttle on a gas golf cart?
Pull the spring that is present around the plastic piece located behind the shifter. Spin it until it falls back. Loosen the throttle cable present in the cable box to adjust the extent to which you can take it out of the housing. Press the accelerator so that the golf cart starts up and begins to idle.
How do you change the speed on a EZGO gas golf cart?
0:287:10Simple Adjusting of an E Z Go Golf Cart Governor - YouTubeYouTubeStart of suggested clipEnd of suggested clip90% of as go-karts have simple springs which limit the speed of the engine to raise the top speed ofMore90% of as go-karts have simple springs which limit the speed of the engine to raise the top speed of your golf cart all you need to do is locate the spring.
How do you increase the torque on a gas golf cart?
Change the Speed ControllerThe Speed Controller regulates the electric output of the motor; a higher voltage equals more RPM, and the faster your cart will travel. When you change the speed controller, you can reduce the voltage and increase the amperage of the motor, resulting in increased torque.
How do you adjust the throttle cable on a EZ Go golf cart?
2:216:13How to Adjust Governor on EZGO RXV Gas Golf Cart | Speed IncreaseYouTubeStart of suggested clipEnd of suggested clipIt's not doing it we're missing over a half a petal of throttle. So now what we will do is go to theMoreIt's not doing it we're missing over a half a petal of throttle. So now what we will do is go to the very back of the car. Make an adjustment who the will actually get it full pedal.
How do you adjust the carburetor on a EZ Go golf cart?
2 Cycle engine: The adjustment screw is on the side of the carburetor and is parallel to the ground. You can identify it by the lock nut at the base of the screw. Loosen this and turn the screw all the way into a soft seat, then back it out one and a half (1-1/2) turns.
Why is my EZGO golf cart so slow?
A EZGO RXV and TXT golf cart can run slow because of a faulty speed sensor, low battery charge and insufficient levels of water in the battery. A problem with the speed sensor. A faulty speed magnet. One or more batteries could are weak and don't have sufficient charge or the water level could be low.
Why is my gas golf cart running slow?
Low Battery Usually, the most common reason golf carts slow down is when they don't get enough power output from the battery. If the battery pack charge is very low and your cart is out of power, your cart will run slow.
How do I make my EZGO TXT faster?
You can make your EZGO golf cart go much faster by adding more torque, upgrading the motor of or increasing the voltage of the batteries.Add more torque.Upgrade the motor.Increase the battery voltage.Decrease the load.
How do I get more power out of my EZGO golf cart?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
How do you adjust the governor on a golf cart?
Adjusting an EZ-GO Golf Cart GovernorStep 1 - First, lift the seat of your engine to reveal seat cousins. ... Step 2 - Remove the seat cushions over your motor. ... Step 3 - Remove the black plastic cover to expose the motor. ... Step 4 - Loosen the smaller one and tighten the larger one to increase your cart's speed.More items...•
How fast can a golf cart go without a governor?
A typical electric cart without an upgraded speed control tops out around 12 mph.
How to adjust EZ Go cart governor?
To adjust an EZ Go Cart Governor engine, start by removing the seat so that you can access the engine. Once the seat is off, remove the screws from the black plastic cover at the rear of the seat and then set the cover aside.
How to make a golf cart go faster?
Loosen the small nut and tighten the larger nut. The more you tighten the larger nut, the faster your cart will go. Start slowly, only tightening the nut a quarter turn to start. You can over-stress the engine if you try to run it too quickly, and it will skip and potentially burn out if you are too eager.
How to get a cart to move faster?
1. Remove the seat and plastic covering over the engine. Sometimes you'll need to remove screws while some models have seats that pop right out. Expose the engine so that you can get to work adjusting the motor. If you don't have a central governor spring, you can still get your cart to move a little faster.
How fast can a golf cart go?
Adjusting the governor can make your golf cart go 5–10 mph (8 .0–16.1 km/h) faster. If you do this to an E-Z-GO golf cart, you might be able to go from 15 mph (24 km/h) to 22 mph (35 km/h). It will only take about 5 minutes to do it. Steps.
How many screws are in a golf cart engine?
There should be five screws in most models. The engine is in the front of golf carts, underneath this panel. Take off the plastic cover and set it aside with the seats. ...
How to change the speed of a car?
Locate your clutch pedal and line. The clutch is the pedal (sometimes a handle near your knee) that you use to put the car into reverse or change speeds. You can adjust the clutch to send more gas to your engine, moving you faster. ...
How to raise the top speed of a golf cart?
To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly. If you cannot find this spring, you likely have a newer model that is more difficult to adjust, though this is rare. Lift up the seat. Remove the seat cousins, which hide the engine.
How to increase octane on EZ Go golf cart?
One way to increase the speed of a gasoline-powered EZ Go golf cart is to add an octane booster when you fill the gas tank. The cart will have more pickup and possibly gain as much as 5 mph. Another approach is to remove the throttle linkage governor on the side of the carburetor, allowing the accelerator pedal to depress farther. But this type of adjustment is limited because golf cart engines have an electronic cutoff that shuts the engine down at a certain rpm. Considering the short turning radius of golf carts, bypassing the cutoff feature on a gasoline-powered cart might compromise personal safety in some instances.
What is an EZ Go golf cart?
EZ Go golf carts are designed for comfort and safety. Newer carts are powered by quiet electric motors and have a controller/sensor that regulates the speed of the cart. Many older carts have gasoline engines with a carburetor and throttle linkage. Aside from using the accelerator pedal to go faster or slower, you have a variety of options for adjusting the speed of EZ Go golf carts.
What happens when you stop a golf cart?
When you stop, a sensor in the controller automatically minimizes the flow of current to the motor. When you apply full throttle, the sensor allows the motor to receive the amperage that’s necessary for top speed. You can obtain a speed controller with a higher output through a golf cart accessory outlet. The overall gain in speed will vary ...
How fast can a golf cart go?
In addition, you notice a cart that’s powered by a 48-volt motor can reach speeds just below 20 mph. With the possible exception of a private cart race, most people prefer leisurely cart rides when playing a round of golf.
How to increase the speed of a golf cart?
Make sure that the governor and carburetor are seated with minimum slack and no tension. Fix the cable in place by tightening the nuts at the end of the cable. As the length of the throttle cable increases, it stops the throttle lever from being pulled back. This will in turn increase the speed of your golf cart.
How to adjust idling on a golf cart?
Press the accelerator so that the golf cart starts up and begins to idle. Check the cable tension to make sure that it’s still loose. The idle screw can be used to adjust the idling if it’s very fast. Turn the key to the OFF position and put the cable back into the box.
How to get a golf cart to idle?
Pull the spring that is present around the plastic piece located behind the shifter. Spin it until it falls back. Loosen the throttle cable present in the cable box to adjust the extent to which you can take it out of the housing. Press the accelerator so that the golf cart starts up and begins to idle.
How to stop a cart from running at less speed?
Compress the spring between the cable stop and the throttle lever to close the throttle until the pedal is away from the microswitch so that the cart can run at less speed with very less throttle. You must do the compression until your problem goes off. Turn the key to the OFF position and press the accelerator pedal.
What to do if throttle plate opens before it should?
If the throttle plate opens before it actually should, loosen the rear cable. If the throttle plate opens at the correct time but only partly, tighten the rear cable. If the throttle plate opens before it actually should but only partly, loosen the front cable and then tighten the rear cable.
What is throttle cable?
The throttle cable plays a key role in ensuring smooth power delivery and acceleration of the cart. It ensures that your golf cart operation is smooth and safe. A throttle cable assists in the efficient utilization of the batteries and gas of the golf cart.
How to run a cable to a governor?
Slide the cable through the little slit present on the side of the cart. Position the cable so that the wire part is in the spool. This ensures that the threaded part of the cable rests on the adjuster bracket. Move the housing backward and adjust the nut to where it was initially. Finally, run the cable to the governor as it was at the start.
Why is my Ezgo golf cart belt so loose?
The reason your EZGO drive belt is too loose could be because it’s worn out, or you’re simply using the wrong size drive belt. In this case, need to find a replacement immediately. A loose drive belt can result in your EZGO Golf Cart to lose top speed and underperform.
Why is my EZGO drive belt so tight?
The reason your EZGO drive belt is too tight can be because you’re not using the right size drive belt. Check and make sure if you’re using the right one. A quick search online will give you the right information. It can also be too tight because the drive/driven clutch is misplaced or broken.
How to tell if golf cart drive belt is too tight?
To check if your drive belt is set just right make sure your golf cart is turned off then check the drive belt by pressing it down between the two clutches with your finger. If it deflects less than 1.5” it’s too tight.
Why is my clutch too tight?
It can also be too tight because the drive/driven clutch is misplaced or broken. A drive belt that’s too tight can damage the drive and driven clutches and can also result in the drive belt being worn out too fast. To check, whether the drive/driven clutch is misplaced or broken call a certified technician to have a look.
How to stop a EZYGO drive belt from slipping?
How to stop a EZYGO drive belt slipping: Make sure that you have the right drive belt. Sometimes the wrong drive belt will not be as wide as the clutch you are putting it on. This gives it an unwanted room to move back and forth when you are using the golf cart.
Can you tighten an EZGO drive belt?
You cannot tighten an EZGO drive belt. If loose, you will need to replace the drive belt. There have been various people online who’ve tried to store it in cold room temperatures hoping it would contract and become smaller but this is not recommended. Putting your drive belt at extreme temperatures can damage it.
Is the Ping G25 adjustable?
Is the Ping G25 driver adjustable? The Ping G25 driver is adjustable. It’s possible to do four adjustments using the hosel adapter of the driver apart from the stated loft setting and...
Jean Leblanc
look above the clutch cable the is a rubber boot, abot 8-10 inches long. If u notice on either end of this boot are rubber prongs, or ears or whatever u wanna call em. Compress the cable by hand trying to bring these rubber ears as close to each other as possible.
Anonymous
SOURCE: EZ Go Golf Cart- Can I get a pdf (or cheap) service manual- if so, where?
golfcartman
No FREE manual site. Some sites have drawings for electric wiring but nothing on the engines. Some dealer sites may be willing to help if you are going to buy parts from them. I have service manuals for all carts, but I am a dealer and they will not let me post as an ad.
golfcartman
Your batteries have died. The reason it will barely move in reverse is that current is being supplied to the motor is a direction that it spends very little time using. There is a slight change in the armature over time, and reverse tends to work better over time. Check the voltage when under load.
Basic EZGO Golf Cart Problems And How To Fix -
Apr 30, 2010 - Electric E-Z-Go Golf Carts are becoming more popular every day ..... I have a ezgo carryall gas golfcart. it has began to pour smoke from rear.
Need electrical schematic for 1990 EZ Go gas cart-2 stroke
You might try the library. They have a reference section for automotive, and maybe golf carts. It has worked for me in the past
1999 ezgo golf cart.need to know the whole wireing system for this cart. I put new batterys in and ihave a short somewhere cause know it want do nothing.the reverse beeper want come on nor will the cart..
When you removed the batteries, a certain procedure MUST be followed. Key switch off, switch to tow position and shift lever in reverse. You must wait until the beeper unit sound dies out then remove the wire from the most NEGATIVE cable. Place in Neutral before installing new batteries.
What happens if you don't adjust your golf cart?
If there's no adjustment left the cable must be stretched. As long as you're getting full throttle and the golf cart is running fine at slower speeds I wouldn't worry about it.
Does the butterfly carburetor need to be adjusted?
No it sounds like the cable needs to be adjusted. The carburetor butterfly should start to open right after the micro switch activates and should close just before the micro switch clicks.
Gasoline Engines
- Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly. If you cannot find this spring, you likely have a newer model that is more difficult to adjust, thou…
- Lift up the seat. Remove the seat cousins, which hide the engine. You may have to unscrew t…
Electric Motors
Speed Controllers
Gearing and Chips
