Club Fitting for Loft and Lie Angles
- Place a sole tape or black electrical tape on the sole of your club.
- Hit a ball solidly off of a lie board
- Measure how far the center of the sole impact impression is from the center of the scoring lines.
- Have your lie angles bent 1 degree for every from the centerline
How to adjust lie angle on irons?
Step:2- Determine the lie angle
- First, find the shaft plate to place it against the shaft.
- Make a setup to read both loft and lie angles. To do this, positioning the lie plate under the shaft can be helpful.
- Record the reading with the exact value for bending at a perfect angle.
How to adjust loft and lie?
Golf Club Loft & Lie Adjustment
- Lie Angle. Lie is the angle from the shaft to the ground when the golf club is placed in a normal playing stance position.
- Loft Angle. Loft is the angle of the club face that controls trajectory of the golf shot and affects distance. ...
- Loft and Lie Can Change With Repeated Club Usage. ...
- Putter Loft and Lie. ...
- Conclusion. ...
What is lie angle and why does it matter?
Your lie angle is the angle between the centre of the shaft and the sole of the club, and it’s important as it can affect how your club enters the turf at impact, and consequently, which direction the ball travels in. A perfect lie angle, commonly referred to as square, is when the sole of your club is parallel with the turf.
Will PING change lie angles?
Your PING iron static fitting recommendations for lie angle and length are determined using the PING Color Code Chart (below) using a combination of your height and wrist-to-floor measurement (first wrist crease). We recommend you take your static recommendations to a certified PING Fitting Specialist for a dynamic fitting session to further fine tune your iron specifications.
Can you adjust the lie angle of golf clubs?
Although lie angle can be adjusted on golf clubs, it is not something you are going to want to have to change back and forth day in and day out.
How much does it cost to adjust lie angle on irons?
Getting the loft and lie angle checked is going to run you anywhere from $2-$5 per club, depending on the amount of work needed. It's a relatively inexpensive tune-up that'll save you some massive headaches once the season kicks into gear, whenever that might be.
How do you adjust the loft and lie on an iron?
2:275:34How To Adjust Loft & Lie - Golf Club Making Tips - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo increase the loft. Apply pressure downward. By applying pressure towards the back of the iron orMoreTo increase the loft. Apply pressure downward. By applying pressure towards the back of the iron or upward the loft will be decreased.
What should my iron lie angle be?
Lie angles almost always range from the mid-50 degrees (in drivers) to the mid-60 degrees (in short irons). In irons, the range is typically from 59 or 60 degrees to around 64 degrees. (Lie angles on putters reach into the 70s.)
Can I change the lie angle on an iron?
The 2-degree limit is only recommended when changing the lofts on irons due to the potential effect such bends will have on the sole angle of the club. If the hosel design and manufacturing processes allow it, the lie of an iron can be bent 3-4 degrees or more with no compromise to the integrity of the head.
How do you know if a lie angle is correct?
After you make impact the line will appear on the face. If it's pointing towards the toe, then your club is too upright. If it's pointing towards the heel, then it's too flat. If the line is perpendicular to the grooves on the face, then your lie angle is correct.
Does upright lie promote a draw?
The upright lie also promotes a left tilting spin axis, which leads to what's generally described as draw spin. An upright lie angle basically gives you a head start, but depending on the severity of the slice conditions the golfer generates, it certainly won't guarantee a draw.
Does changing loft change lie angle?
As you change the loft and the face angle, you will also change the lie unless there is a separate setting to alter the lie independently of loft.
What happens if my lie angle is too flat?
If your lie angle is too flat, you will tend to slice the ball. If your lie angle is too upright, then you will tend to hook the ball. It can even cause you to develop swing compensations to correct for it, preventing you from ever developing a consistent, repeatable, and powerful swing.
What is the standard lie of a 7 iron?
62.5 degreesWhat Is The Standard Lie Angle For A 7 Iron? Most golf club manufacturers 7 iron lie angles are 62.5 degrees.
Does lie angle affect distance?
On average, our testers were 3 yards closer to their target with their best fit lie angle. That's the difference between a birdie putt inside 10 feet and one that's closer to 20. Bonus myth: do more upright clubs produce shots that go further left?
Does 1 degree upright make a difference?
Yes it will make a difference, I play 2 degree upright and +1/2. If your hitting the ball left all the while (I am guessing your right handed) won't be to do with having the lye angle to flat.
What is a lie in golf?
Lie is the angle from the shaft to the ground when the golf club is placed in a normal playing stance position. It enables the sole of the club head to strike the ground flat if it is correct. An incorrect lie negatively impacts your golf club performance. It will prevent you from making good ball contact.
What is the tendency of a putter to move the ball slightly to the left?
PUTTER LIE. If the toe of the putter is sticking up in the air with the heel down, the tendency is to pull the ball slightly to the left (for a right handed golfer). Conversely, if the toe of the putter is down and the heel is up in the air, the tendency is to push the ball slightly to the right (for a right handed golfer).
What is loft angle?
Loft Angle. Loft is the angle of the club face that controls trajectory of the golf shot and affects distance. Stronger or weaker lofts can lead to higher, lower, longer, or shorter ball flights. The standard loft on manufactured golf clubs varies from brand to brand. Loft is considered to be more of an individual preference based on ...
What happens if your club head is touching the ground?
If the toe of the club head is touching the ground, your shots will have a tendency to travel to the left or hook left (for a right handed golfer). In this case, you would require a lie angle adjustment (bending) that would lower the lie angle. Conversely, if the heel of the club is touching the ground, your shots will have a tendency to fly to ...
What is the standard loft for putting greens?
The standard built-in loft of most putters is two to four degrees. The rule of thumb: Slow greens need more loft; Fast greens require less loft.
Can you adjust your putter to match your stroke?
Therefore, you can improve your putting stats by having your putter adjusted to match your physical build and putting stroke.
Can you adjust the club lie?
The club lie can be adjusted for a golfer that has a more upright or flatter swing. For unusually tall or short golfers, club lie is critical. When standing at address with a golf club, if the bottom of the club head is touching the ground more on the heel (lie too upright) or toe (lie too flat), the lie needs to be adjusted.
Why is a lie angle important in golf?
Lie angle is the most important component in irons and wedges that will determine how well you hit and how fast you will improve your game.
How often should you check your golf club lie angle?
So you should always check you lie angle first on your iron and wedges. We recommend getting checked at least once a year but could be more frequent when going through swing changes or club changes. Here is how a lie fitting procedure usually goes: Choose a club head that you like to play.
How to tell if you have an incorrect lie angle?
Symptoms of incorrect lie angle: Let’s say the green mark is where you see your wear mark on the sole of your irons or wedges. Lie is too flat or you are closing your face too much. A good club fitter will be able to tell you if it is a lie issue or a over rotation of the club head during the swing. When you see the wear mark on the heel, the lie ...
What happens when you practice with a wrong lie angle?
When you are practicing with a wrong lie angle, you end of getting use to bad habits. If irons are too flat, ball should go high right but when you practice hard to make it go straighter, you compensate for the incorrect lie by shutting the face to make it go straighter but not very efficient ball striking. When you have a proper lie, your ball ...
What does it mean when you see a wear mark on your heel?
When you see the wear mark on the heel, the lie angle is too upright. In both cases (toe and heel) you are not getting the nice feel when you get when you hit the sweet spot (unless the ball is teed up, sitting up on the grass or hitting from a ball above or below your feet.)
What happens if you lie too upright?
Basic theory: If lie is too upright, ball will go left (for righthanded golfers ) and if lie is too flat, ball will go right. Golfers who have never checked his/her lie angle goes out to practice and work on compensating with their swing for the incorrect lie angle. (i.e.
Can you hit the ball left or right?
You may still hit the ball left or right but now you can focus on your swing since it is now the swing (or other parts of the club like shaft and grip) that may influence ball flight. Always blame the club spec first and if all looks good, it is your swing.
What is the lie angle of a golf club?
The "lie angle" of any golf club is the angle formed between the center of the shaft and the sole, or ground line, of the club when the club is soled in its proper ...
What happens if the lie angle of your golf clubs is ill-suited to you?
When the lie angle of your clubs is wrong for your swing or body type, you can put a great swing on the ball and still have problems with accuracy. Poorly fitting lie angles create pushes and pulls and other mishits.
What does it mean when your divots are deeper on the toe side than the heel side?
If your divots are deeper on the toe side than the heel side (toe down, heel up at impact) or deeper on the heel side than the toe side (toe up, heel down at impact), that's a sign your lie angles might be too flat or too upright.
What is the lie angle on a 9 iron?
Upright lie angle: A lie angle that is higher than the standard lie angle (a 66-degree lie angle on a 9-iron is more upright than the standard 9-iron lie angle of around 64 degrees). You might hear a golfer (or clubfitter) saying things such as, "You need flatter lie angles on your irons," or "I had my irons bent 1-degree upright.".
Why is a proper lie angle important?
Proper Lie Angle Is More Important in Irons Than in Woods. Don't misunderstand: Lie angle is an important factor in all golf clubs, even the putter. But having improperly fit lie angles causes more problems in irons than in the woods.
What is lie angle?
Lie angle is a factor that affects the accuracy of golf shots. Golfers who use clubs whose lie angles don't fit their body types and/or golf swings are costing themselves strokes. Matching the lie angle of clubs to the specific golfer is one of the goals of a clubfitting session.
What is the range of lie angles?
Lie angles almost always range from the mid-50 degrees (in drivers) to the mid-60 degrees (in short irons). In irons, the range is typically from 59 or 60 degrees to around 64 degrees. (Lie angles on putters reach into the 70s.)
How to wear golf shoes?
While wearing your golf shoes or street shoes stand on the floor with your normal posture, looking straight ahead, and have your arms hanging in a relaxed position by your sides.
What is the angle of the club shaft when you hit the ball?
Lie angle is the angle the club shaft makes with the ground when you HIT the ball and your club head is parallel with the ground.
Froglegs
I've always been more of a feel player so I'd much rather take to the course and see what's comfortable / let results over several rounds dictate lie angle rather than a few measurments with a lie board and whatever swing I bring to the club fitter that day.
Nessism
Golfsmith and Golfworks both make a simple iron bending clamp device so you can bend your own. I made my own version and used it for a good many years before coming across a good deal on a real loft and lie machine. Having a spec gauge takes some of the guess work out of the process.
hbear
Tough to do without a proper way to measure the results.......1* doesn't look like much.
Froglegs
Thanks everybody, I appreciate the suggestions. I would like to talk to the owner of a fitting shop and see if I could pay to use the machine myself.
Nessism
No worry about repeatedly bending. As long as you stay within the limits of the material you can bend several times without concern.
hbear
The difficulty without a proper gauge is making sure the club is setup in the same orientation each time you measure. Small play at various points will throw off the measurement quite a bit.
hbear
You might be able to measure, but I'd suggest the precision (e.g.
