EZGO ITS Adjustment Instructions for adjusting a Inductive Throttle Sensor: Break the allen screw loose with a 5/64th allen wrench. Loosen the 1/4" jamnut with a 7/16" open end wrench (hold the slide end with a open end 9/16" wrench). Back the 1/4" jam nut off several turns.
Full Answer
How do you adjust the throttle cable on an EZGO golf cart?
How do you adjust the throttle cable on an EZGO golf cart? Close the carburetor throttle plate.. Rotate the governor arm in a counter-clockwise direction.. Keep the cable inside the throttle cable bracket that is fitted on the rear axle.. Make sure that the governor and carburetor are seated with ...
What is an inductive throttle sensor in an EZGO?
The inductive throttle sensor in an EZGO is a part of the electrical system of the golf cart and is connected through a wiring harness to the direction selector. It functions inside the pedal box. The ITS is used along with the cart’s electric speed controller like PDS, DCS and Series.
How to adjust the slide Tube on a golf cart?
With full pedal depression the slide tube must be flush with the end of the ITS (some protrusion is ok). Once the adjustments are complete tighten the allen screw and jam nut. the golf cart shouls smoothly take off.
How do you adjust the gas pedal on a carburetor?
Adjust the rear cable from the governor arm to the gas pedal until the slack is almost nil. Also, adjust the front cable from the carburetor to the governor arm until the carburetor stops opening before the motor starts getting cranked by the gas pedal switch.
How does an EZGO inductive throttle sensor work?
For example, when you press your gas pedal down, an electrical signal gets sent to the inductive throttle sensor to get an idea of how much speed that you want. Once this part receives that signal, it sends an electrical signal to the throttle in the cart to produce the proper speed.
How do you adjust the throttle on a EZGO golf cart?
Pull the spring that is present around the plastic piece located behind the shifter. Spin it until it falls back. Loosen the throttle cable present in the cable box to adjust the extent to which you can take it out of the housing. Press the accelerator so that the golf cart starts up and begins to idle.
How do you adjust the link on a EZGO golf cart?
1:467:10Simple Adjusting of an E Z Go Golf Cart Governor - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you are curious this is your carts carburetor. Five loosen the small nut and tighten the largerMoreIf you are curious this is your carts carburetor. Five loosen the small nut and tighten the larger nut.
How do you test the throttle sensor on a EZGO golf cart?
Take a digital multimeter and set it to the volts reading. Place the positive probe of the meter on the white wire terminal of the ITS. Release the accelerator pedal slowly. The reading should be in the 0.45V to 0.53V range when the micro-switch gets activated.
How can I make my EZ GO TXT gas faster?
One way to increase the speed of EZ Go golf carts is to incorporate an octane booster when you fill the tank. The cart will have more pick-up, and it could gain as much as 5 mph. A different approach is to take out the throttle linkage governor on the carburetor.
How do I speed up my EZ GO TXT?
In order to get the maximum speed from your EZGO Marathon cart, you will need to upgrade the amp controller. Most carts come with a default 275 amp controller. Try replacing the amp controller with a 500-amp or a 400-amp controller. This will help the cart to go faster during uphill and downhill movements.
How do you adjust the forward and reverse cables on a EZ Go golf cart?
You can do the shift cable adjustment, with the shift lever in the forward position and then again changing it to the reverse position.
How do you adjust the governor on a golf cart?
0:545:06How to Adjust an E Z Go Golf Cart Governor - WikiVideo - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you are curious this is your carts carburetor loosen the small nut and tighten the larger nut.MoreIf you are curious this is your carts carburetor loosen the small nut and tighten the larger nut. The more you tighten the larger nut the faster your cart will.
How fast can a golf cart go without a governor?
A typical electric cart without an upgraded speed control tops out around 12 mph.
Where is the reset button on a ezgo golf cart?
Look in the area where several electrical wires enter the motor and locate a small red button. This is the reset button.
Why is my ezgo golf cart so slow?
A EZGO RXV and TXT golf cart can run slow because of a faulty speed sensor, low battery charge and insufficient levels of water in the battery. A problem with the speed sensor. A faulty speed magnet. One or more batteries could are weak and don't have sufficient charge or the water level could be low.
How do I fix my EZGO speed controller?
Here are 5 steps you should follow for a DIY fix to your golf cart's speed controller.Flip the maintenance switch. ... Reset the battery cable. ... Check your connections. ... Test the solenoid. ... Check your controller's power output.