
How to adjust the brakes on your E-Z-GO golf cart in a few simple steps Turn on the cart and accelerate to maximum speed. Once you’ve reached your maximum speed, depress the brake pedal to apply the brakes to the vehicle.
Full Answer
How do the brakes work on an E-Z-GO golf cart?
The E-Z-GO golf cart is equipped with a mechanical rear drum braking system that adjusts automatically based on brake shoe wear. The brakes adjust while the golf cart is moving.
How do you adjust the brakes on a golf cart?
Get into the driver's seat of the golf cart. Accelerate to full speed. Make sure you have enough room. Press on the brake pedal to fully engage the braking system and then release the pedal before coming to a full stop. The golf cart must be moving for the braking system to adjust.
Do EZ GO golf carts need to be cleaned?
If the EZ-GO golf cart is old which has been used for at least five to seven years then they must clean the brake drum first. Cleaning is very necessary to make the brakes work perfectly.
How do you adjust the speed on an EZ GO golf cart?
Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.

How do I adjust the brakes on my ezgo golf cart?
To find the brake adjustment screw, you will need to take the rubber boots off the wheels. Yank the rubber boots by your hands, and make sure you pull them hard. Now, you will need to make the brake pads move closer toward the brake drum by turning the adjustment screw in a way that it moves toward the wheels.
How do you adjust disc brakes on a golf cart?
1:533:35How to Adjust Brakes on a Club Car Precedent Golf Cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn it counterclockwise. So we'll get the amount of play that we want don't want to over tightenMoreTurn it counterclockwise. So we'll get the amount of play that we want don't want to over tighten this because you'll put a strain the breaks use all the time. And we've got it just like we want.
How do you check the brakes on a EZ Go golf cart?
0:343:20How to Inspect Your Golf Cart's Brakes | Golf Cars Unlimited - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe center nut has been removed. And you're gonna hold onto that to put that on later you can simplyMoreThe center nut has been removed. And you're gonna hold onto that to put that on later you can simply just pull the drum straight off of the vehicle. Put that in a safe place you don't want it to fall.
How do the brakes work on a golf cart?
The conventional golf cart has rear brakes to stop the cart because of the low speed. Apparently, the brakes at the rear wheels do not have to exert much force to stop the cart. But, as golf cart owners seek more powers, it ultimately requires more brakes to cope with an increase in speed.
What causes golf cart brakes to lock up?
Why Do Golf Cart Brakes Lock Up? Golf cart brakes can start locking up when the brake cable gets stuck, or when the bolts on the lift kit are loose. The brake cable gets stuck because of a binding, resulting in a mechanical linkage. One or more parts of the pivot assembly have rusted.
How much does it cost to replace brakes on a golf cart?
The brake system in a golf cart is made of several components. Replacing the brake system will mean replacing all the components. A complete brake replacement costs $150-$200.
How do you clean golf cart brakes?
Keep Them Clean First, lift the axle the brakes are on using a jack. Take off the wheels and brake drums from the studs. Use an aerosol brake parts cleaner to blow any accumulated dust and loose debris off the shoes. Once that's done, damped a clean rag with WD-40 and wipe away anything that didn't blow loose.
How do you bleed the brakes on a golf cart?
3:034:49Bad Boy Buggy Garage - "Brake Bleeding & Service Adjustments"YouTubeStart of suggested clipEnd of suggested clipWe're gonna start the bleed process at the right rear corner. While Allen pumps up the pedal. I'mMoreWe're gonna start the bleed process at the right rear corner. While Allen pumps up the pedal. I'm gonna ask him to hold pressure on it I'm gonna then open up the bleeder screw.
Do golf carts have brake pads?
They vary in price, size and propulsion, but all carts have one common component: brakes. If you own a golf cart, eventually the brakes will require replacement just like those on your automobile. Golf cart brake pads will make an audible noise when they have worn to the point of requiring replacement.
How to Adjust Brakes on EZ-Go Golf Cart?
Today we will discuss how one can adjust the brakes on an EZ-GO golf cart.
Why do you need to adjust the brakes of a golf cart?
Basically, to get safe from any dangerous situation one must adjust the break after sometimes. As time passes and a golf cart gets old the brakes of the golf carts also gets weaken. The break shoe or the brake pad gets worn out or gets loosen. Therefore the brake seems to be not working perfectly.
Adjusting breaks on EZ-GO golf cart
Different manufacturers use different mechanisms to make their golf carts. Some golf carts have their auto adjustable brake mechanism. These types of carts do not need their break to be adjusted.
How to adjust brakes on a golf cart?
Here are the steps in adjusting the brakes: Turn off the power of the golf cart. Don’t set its parking brake. Put the brick or blocks in front and behind each of the front wheel of the golf cart to prevent it from rolling. Get the floor jack into position at the rear of the golf cart.
Why is it important to adjust the distance of travel on a golf cart?
It is important to adjust this distance of travel to make sure that the brakes are working properly. If there is too much travel distance, the braking capacity or power of the golf cart will be reduced. But if the distance is too short, the brakes may not release fully. So adjustments are necessary in both cases.
How to remove lug nuts on a car?
Use the socket wrench to loosen the lug nuts on the rear wheels. Remove the nuts and the wheels and set them aside. Remove the rubber boots on the underside of the wheels and the brake adjustment screw will be exposed. Pull these rubber boots away from the wheels by using your hands.
Do golf carts have brakes?
As in ordinary vehicles, golf carts have brakes. If you notice that the brakes are not functioning well, they need to be adjusted. Here are some of the ways by which you can adjust the brakes of different types of golf carts. This is also part of the golf cart maintenance checklist that we’ve created. Contents [ show]
Is it safe to drive a golf cart?
Just like any vehicle, safety is very important in driving a golf cart. If not properly handled a golf cart could also cause accidents, although not as serious as the accidents caused by bigger cars and trucks. Nevertheless, you should also know how to safely drive and operate a golf cart. As in ordinary vehicles, golf carts have brakes.
Do old golf carts have low switches?
Some of the old style golf carts may have run/low switches. These switches should be shifted to the tow position before disconnecting their battery packs. Lift the back of the golf cart and put the floor jack in a secure section of the cart which should provide it a stable support.
Operation
As we understand, the motor brake on the EZGO RXV is controlled in an electromagnetic fashion. The circular shoe comes in contact with the brake disk when parking or when braking is needed. The signal to “brake” is controlled via a brake sensor and a throttle sensor on the brake / accelerator pedals respectively.
Failure
Anything mechanical or electrical, including this brake system can be subject to fail. But, brakes are not a system which should be ignored, or neglected due to the risk of serious injury and damage. In our initial inquiry to the customer, we were told that the cart wasn’t driven far after the “burning” smell started.
How to adjust EZ Go cart governor?
To adjust an EZ Go Cart Governor engine, start by removing the seat so that you can access the engine. Once the seat is off, remove the screws from the black plastic cover at the rear of the seat and then set the cover aside.
How to raise the top speed of a golf cart?
To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly. If you cannot find this spring, you likely have a newer model that is more difficult to adjust, though this is rare. Lift up the seat. Remove the seat cousins, which hide the engine.
How to make a golf cart go faster?
Loosen the small nut and tighten the larger nut. The more you tighten the larger nut, the faster your cart will go. Start slowly, only tightening the nut a quarter turn to start. You can over-stress the engine if you try to run it too quickly, and it will skip and potentially burn out if you are too eager.
How to get a cart to move faster?
1. Remove the seat and plastic covering over the engine. Sometimes you'll need to remove screws while some models have seats that pop right out. Expose the engine so that you can get to work adjusting the motor. If you don't have a central governor spring, you can still get your cart to move a little faster.
How fast can a golf cart go?
Adjusting the governor can make your golf cart go 5–10 mph (8 .0–16.1 km/h) faster. If you do this to an E-Z-GO golf cart, you might be able to go from 15 mph (24 km/h) to 22 mph (35 km/h). It will only take about 5 minutes to do it. Steps.
How many screws are in a golf cart engine?
There should be five screws in most models. The engine is in the front of golf carts, underneath this panel. Take off the plastic cover and set it aside with the seats. ...
How to change the speed of a car?
Locate your clutch pedal and line. The clutch is the pedal (sometimes a handle near your knee) that you use to put the car into reverse or change speeds. You can adjust the clutch to send more gas to your engine, moving you faster. ...
How to rotate a star wheel on a golf cart?
Engage the front brake shoe towards the rear of the cart and hold, Engage the brake lever. The adjuster arm should engage the star wheel and start to rotate. Should the adjuster arm engage and rotate the star wheel then the system is working correctly.
What does it mean when your wheel brakes are not self-adjusting?
If too much free travel is experienced then you have a problem with either of your wheel brakes not self-adjusting or cables/linkages wear. Inappropriate pedal free travel means you have issues with either of wheel brake self-adjustment or brake linkages. 4. Inspection of the brake cables.
How to inspect brake pedal return bumper?
Inspection of brake pedal return bumper. Ensure the brake pedal is meeting the pedal return bumper when disengaged. The bumper should be in good condition whereby a 1/4 – 3/8″ (6 – 9.5 mm) space occurs between the setscrew heads of the kick-off cam and brake pedal arm. If necessary replace the brake pedal system. 2.
What should the brake pedal arm contact?
The brake pedal arm should contact the pedal bumper when disengaged. The torsion spring should be wrapped around the pedal and frame. Should the pedal have a slow return or not return home fully then the bushings and pivot bolt needs replacement. If necessary replace all pedal, spring, bushings and hold down bolt. 3.
What is brake fluid travel?
Brake pedal fluid travel is the gap the pedal moves from the stationary position to when the brake cables just begin to energize the brake levers. Adjusting the fluid travel is essential to ensure the brakes work correctly. If you experience too much pedal fluid travel you will have limited braking capacity. If you experience too little pedal fluid travel you will cause the brakes to not fully release.
