How do you adjust the speed on an EZ GO golf cart?
Step 1 Locate the governor arm mounted on top of the rear axle case underneath the cart. The action of the throttle cable attached to the governor arm is dampened by an adjustable governor spring mounted on a bracket adjacent to the governor arm. Step 2 Loosen the adjusting locknut on the end of the governor spring.
How long does it take to adjust the governor on an EZGO?
How to Adjust the Governor on a Gas E-Z-Go Golf Cart Locate the governor arm mounted on top of the rear axle case underneath the cart. Loosen the adjusting locknut on the end of the governor spring. Retighten the adjusting locknut.
How do you adjust the governor on a golf cart?
Mar 24, 2015 · Link to part on our website: http://www.diygolfcart.com/EZGO-Throttle-Cable-p/cbl-051(6429).htmLearn how to adjust your governor or throttle cable on an EZGO...
How do you bypass the governor on an EZGO golf cart?
Steps to Adjust EZ-GO Golf Cart Governor. Step 1 - First, lift the seat of your engine to reveal seat cousins. You may need to remove screws in some carts, and they often have Philips heads, so make sure your toolset has this available if required. Step 2 - …
How do I make my EZ Go golf cart go faster?
One way to increase the speed of EZ Go golf carts is to incorporate an octane booster when you fill the tank. The cart will have more pick-up, and it could gain as much as 5 mph. A different approach is to take out the throttle linkage governor on the carburetor.Jun 16, 2015
How do you adjust the throttle on a EZ Go golf cart?
2:216:13How to Adjust Governor on EZGO RXV Gas Golf Cart | Speed IncreaseYouTubeStart of suggested clipEnd of suggested clipIt's not doing it we're missing over a half a petal of throttle. So now what we will do is go to theMoreIt's not doing it we're missing over a half a petal of throttle. So now what we will do is go to the very back of the car. Make an adjustment who the will actually get it full pedal.
How do you remove the governor on a EZ Go golf cart?
General InstructionsDetach the cable from the carburetor. The cable is about the width of a straw. ... Follow the disconnected cable up to the governor. ... Disconnect the gas pedal cable from the governor and reroute it to the carburetor. ... Using your wrench, remove the bolt on the gas pedal shaft.
Where is the governor on a golf cart?
0:061:28Where Is a Golf Cart Governor Located? - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell a golf cart's governor located is actually down in the motor. Compartment.MoreWell a golf cart's governor located is actually down in the motor. Compartment.
How does a golf cart governor work?
By mechanically pulling the throttle lever back, you decrease the gas flow to the engine and control the golf cart's speed. This governor can be adjusted by adjusting the cable nut which holds the cable to the throttle lever.Sep 5, 2004
How do you take the governor off a electric golf cart?
0:000:46How to remove governor on a Club Car golf cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt looks up look inside. There's 12 cable down right here this lever you want to lift up and BendMoreIt looks up look inside. There's 12 cable down right here this lever you want to lift up and Bend and that pulls on the cable a little more.
How do I adjust my EZ GO carburetor?
2 Cycle engine: The adjustment screw is on the side of the carburetor and is parallel to the ground. You can identify it by the lock nut at the base of the screw. Loosen this and turn the screw all the way into a soft seat, then back it out one and a half (1-1/2) turns.Feb 25, 2021
How to Adjust an E Z Go Golf Cart Governor: 13 Steps
Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly. More ›
Only 2 methods tell you How to Adjust an E Z Go Golf Cart ..
Adjusting the Common 4-Stroke Engine Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly. More ›
How to Adjust the Throttle on a Golf Cart (STEPS) - Golf ..
EZGO TXT throttle adjustment The throttle adjustment for 1996 to 2003 model EZGO TXT golf carts can be done as given below. Ensure that the throttle plate is closed fully and the governor arm is rotated in the counter-clockwise direction completely. Loosen the nut that is near the throttle cable bracket and positioned towards the back of the cart.
How to Adjust & Troubleshoot a Golf Cart Carburetor (STEPS ..
EZGO Gas Cart Carburetor Adjustment Adjust the idle jet pilot screw on the carburetor. This can be done by doing a 1/4 turn of the screw. Do a valve clearance adjustment starting with the cold valve. More ›
How to Adjust the Drive Belt on a EZGO Golf Cart (STEPS ..
EZGO Golf Cart Model . Drive Belt Measurements. EZGO 2001-up 480 CC 49" Outside Diameter. EZGO 1994-Up 4 Cycle Gas Vehicle with Robin Engines. 1-3/16″ Wide x 42″ Outside Diameter
Why is My Golf Cart Backfiring? (Troubleshooting Guide ..
How to stop EZGO TXT golf cart from backfiring. The following are some ways EZGO TXT golf cart owners have stopped backfiring in their carts. Adjusting the governor so that the rev limiter doesn't reach the maximum limit helps to resolve the problem. Readjusting the valves to 0.005 or 0.006 inches solves the issue. More ›
How To Make EZ Go Gas Golf Cart Faster - Golfer Watch
The first method only works with around 90 percent of EZ Go gas golf carts, which were manufactured with engines containing a governor spring. For the other 10 percent, you may increase your cart's speed with this second method. Step 1 Before exposing your engine, always make sure that your golf cart is turned off. More ›
How fast is an EZGO golf cart?
The top speed of an EZGO golf cart is usually 19.9mph and the average speed is 14mph to 15mph. With governor adjustment, the EZGO cart can go faster by 5 to 10mph.
What is a golf cart governor?
A golf cart governor is a mechanical device that helps in controlling the maximum speed of the cart when it moves on flat ground. This device prevents the engine RPMs from increasing beyond the recommended specifications.
How to start a golf cart with a gas pedal?
Locate the gas pedal that is fitted to the governor and remove the connection. Re-route the gas pedal to the carburetor. Remove the bolt present on the shaft of the gas pedal. Slide the shaft upwards so that the gas pedal has more play. Tighten the bolt and start the golf cart.
How to change the speed of a golf cart?
Locate the spring on the differential or carburetor that helps in changing the cart speed by adjusting its tension. Increase the length of the cable that is fitted on to the body of the throttle and clutch of the two-stroke engine.
How to ride a golf cart at full speed?
Ride the cart at full speed over a course of known length. This will ensure that the governor controls the speed of the cart within factory specifications. Fasten the black plastic cover and put the seat back in place. Take care when tightening the nut. The more you tighten, the faster your cart will go.
Where is the governor arm on a golf cart?
Locate the governor arm of the golf cart. This is mounted above the rear axle housing and under the cart. Depending on the cart model, there may be a protection plate above the governor.
Can you remove a golf cart governor?
It doesn’t take much time or skill to remove a golf cart governor. With some basic mechanical expertise and general-purpose tools, you can do this yourself. The process is more or less the same in all golf carts.
