How to Adjust the Governor on a Gas E-Z-Go Golf Cart
- Locate the governor arm mounted on top of the rear axle case underneath the cart. ...
- Loosen the adjusting locknut on the end of the governor spring. Rotate the locknut to expand or compress the spring until its length is 2 1/2 inches.
- Retighten the adjusting locknut.
- Road test the cart by timing it over a course of known length at full speed to verify that the governor is controlling the speed within factory specifications.
How do I adjust an EZ Go Cart Governor engine?
To adjust an EZ Go Cart Governor engine, start by removing the seat so that you can access the engine. Once the seat is off, remove the screws from the black plastic cover at the rear of the seat and then set the cover aside.
What happens if you adjust the governor on a golf cart?
Your golf cart's warranty is instantly voided if you make any adjustment in the governor. No golf cart shop will help fix an engine-related problem once they find out you have tampered with the governor. Engine damage may occur if the cart is run at excessively high speeds.
How do you adjust the throttle on an EZGO golf cart?
In some cases, the adjustment can be done by turning the cable nut that connects the cable to the throttle lever in the counter-clockwise direction. This type of governor is often found in 2-cycle golf carts. The top speed of an EZGO golf cart is usually 19.9mph and the average speed is 14mph to 15mph.
How many horsepower does an EZ GO golf cart have?
E-Z-Go gas-powered golf carts are equipped with 9-horsepower, 295 cc Robin engines. Designed entirely for use on golf course trails, E-Z-Go carts are not engineered for higher-speed on-road use and/or cornering.
How do you adjust the speed limiter on a EZ Go golf cart?
Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.
How do I make my ezgo gas golf cart go faster?
One way to increase the speed of EZ Go golf carts is to incorporate an octane booster when you fill the tank. The cart will have more pick-up, and it could gain as much as 5 mph. A different approach is to take out the throttle linkage governor on the carburetor.
How do you adjust the governor on a gas club golf cart?
If you find this rod, then your governor can be easily adjusted by accessing the cart's inner workings. Simply adjust the cable coming from this metal protrusion, turning the nut counterclockwise to make the cable longer, effectively adjusting the cart's governance to increase the overall speed.
Where is the governor on a gas golf cart?
0:061:28Where Is a Golf Cart Governor Located? - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell a golf cart's governor located is actually down in the motor. Compartment. Some of them theseMoreWell a golf cart's governor located is actually down in the motor. Compartment. Some of them these electric ones nowadays. Actually the governor isn't a true governor. It is a control speed.
Why is my EZGO golf cart so slow?
A EZGO RXV and TXT golf cart can run slow because of a faulty speed sensor, low battery charge and insufficient levels of water in the battery. A problem with the speed sensor. A faulty speed magnet. One or more batteries could are weak and don't have sufficient charge or the water level could be low.
Why is my gas golf cart running slow?
Low Battery Usually, the most common reason golf carts slow down is when they don't get enough power output from the battery. If the battery pack charge is very low and your cart is out of power, your cart will run slow.
How do you adjust the carburetor on a EZGO golf cart?
2 Cycle engine: The adjustment screw is on the side of the carburetor and is parallel to the ground. You can identify it by the lock nut at the base of the screw. Loosen this and turn the screw all the way into a soft seat, then back it out one and a half (1-1/2) turns.
Where is the speed controller on an EZGO golf cart?
These speed controllers are located under the EZGO cart seat. Check the speed controller's attachment near the carburetor.
How can I increase the speed of my golf cart?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
How do I turn off the governor on my EZ GO?
0:040:46How to remove governor on a Club Car golf cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou open up this box lap. Here. It looks up look inside. There's 12 cable down right here this leverMoreYou open up this box lap. Here. It looks up look inside. There's 12 cable down right here this lever you want to lift up and Bend and that pulls on the cable a little more.
What does the governor do on a golf cart?
How Does a Golf Cart Governor Work? A golf cart governor is a mechanical device that helps in controlling the maximum speed of the cart when it moves on flat ground. This device prevents the engine RPMs from increasing beyond the recommended specifications.
What does removing the governor do?
Removing the governor will increase the maximum rpm of the engine, but the internal parts of the Predator 212 are designed for 3600 rpm. Generally, this isn't an issue with just the governor removal, the internal parts can usually withstand 5000 rpm without breaking apart (unless you go full throttle for too long).