
How to Adjust the Governor on a Gas E-Z-Go Golf Cart
- Locate the governor arm mounted on top of the rear axle case underneath the cart. ...
- Loosen the adjusting locknut on the end of the governor spring. Rotate the locknut to expand or compress the spring until its length is 2 1/2 inches.
- Retighten the adjusting locknut.
- Road test the cart by timing it over a course of known length at full speed to verify that the governor is controlling the speed within factory specifications.
How do you bypass the governor on an EZGO golf cart?
You can bypass the governor connection in an EZGO or Yamaha G1 golf cart as given below. Remove the cable connecting the carburetor and the governor. Disconnect the connection between the gas pedal and the governor. Connect the gas pedal directly to the carburetor opening.
How do you adjust the speed on an EZ GO golf cart?
Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.
How do you adjust the governor on a golf cart?
Loosen the adjusting locknut on the end of the governor spring. Rotate the locknut to expand or compress the spring until its length is 2 1/2 inches. Retighten the adjusting locknut. Road test the cart by timing it over a course of known length at full speed to verify that the governor is controlling the speed within factory specifications.
Can you adjust the governor on an EZ GO spark plug?
Many manufacturers, including EZ Go, do not want consumers tampering with their engines, and have thus hidden the governors in the spark plug ignition. This is very difficult to adjust without ruining the engine, and should be left to trained professionals. How can I stop the choke cable from getting hot on my EZ-GO golf cart?

How do you adjust the speed limiter on a EZ Go golf cart?
Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.
How do I make my ezgo golf cart go faster?
One way to increase the speed of EZ Go golf carts is to incorporate an octane booster when you fill the tank. The cart will have more pick-up, and it could gain as much as 5 mph. A different approach is to take out the throttle linkage governor on the carburetor.
Is there a governor on an electric ezgo golf cart?
Considering electric golf carts don't have governors like gas powered carts, the old-school method of simply removing the governor is not an option.
How do I turn off the governor on my EZ GO?
0:040:46How to remove governor on a Club Car golf cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou open up this box lap. Here. It looks up look inside. There's 12 cable down right here this leverMoreYou open up this box lap. Here. It looks up look inside. There's 12 cable down right here this lever you want to lift up and Bend and that pulls on the cable a little more.
Where is the governor on a ezgo golf cart?
0:545:06How to Adjust an E Z Go Golf Cart Governor - WikiVideo - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe engine is in the front of golf carts underneath this panel. Take off the plastic cover and setMoreThe engine is in the front of golf carts underneath this panel. Take off the plastic cover and set it aside with the seats. Follow the thickest cable coming from the gas pedal until your find a small
Why is my ezgo golf cart so slow?
A EZGO RXV and TXT golf cart can run slow because of a faulty speed sensor, low battery charge and insufficient levels of water in the battery. A problem with the speed sensor. A faulty speed magnet. One or more batteries could are weak and don't have sufficient charge or the water level could be low.
How can I make my electric golf cart go faster without upgrading?
How to Make an Electric Golf Cart Faster Without UpgradesWash Your Cart Properly. ... Inspect the Batteries. ... Refill the Battery Water. ... Check the Gas Pedal and Linkage. ... Measure the Tire Pressure. ... Charge Up Your Battery Unit. ... Lighten Up Your Cart's Weight.
What does removing the governor do?
Removing the governor will increase the maximum rpm of the engine, but the internal parts of the Predator 212 are designed for 3600 rpm. Generally, this isn't an issue with just the governor removal, the internal parts can usually withstand 5000 rpm without breaking apart (unless you go full throttle for too long).
Why is my electric golf cart so slow?
Low Battery Usually, the most common reason golf carts slow down is when they don't get enough power output from the battery. If the battery pack charge is very low and your cart is out of power, your cart will run slow.
Where is the speed controller on an ezgo golf cart?
These speed controllers are located under the EZGO cart seat. Check the speed controller's attachment near the carburetor.
How can I make my gas golf cart go faster?
How to Make Your Gas-Powdered Golf Cart Faster [Updated, 2022]1 Use A Better Golf Cart Battery.2 Increase Torque.3 Upgrade the Golf Cart Motor.4 Install a Torque Converter.5 Install a Higher-Performance Clutch.6 Tweak The Governor.7 Install A Cold Air Intake.8 Get Bigger Golf Cart Tires.More items...
How to adjust golf cart governor?
The governor on a golf cart can be adjusted easily by loosening the tension on its springs using a wrench or screwdriver to get the golf cart going at a relatively faster speed.
How Does a Golf Cart Governor Work?
A golf cart governor is a mechanical device that helps in controlling the maximum speed of the cart when it moves on flat ground. This device prevents the engine RPMs from increasing beyond the recommended specifications.
How to increase the speed of a cart?
Loosen the nut fitted on the cable. This will gradually increase the length of the cable. As the length increases, the speed of the cart will increase accordingly.
How to start a golf cart with a gas pedal?
Locate the gas pedal that is fitted to the governor and remove the connection. Re-route the gas pedal to the carburetor. Remove the bolt present on the shaft of the gas pedal. Slide the shaft upwards so that the gas pedal has more play. Tighten the bolt and start the golf cart.
How fast is an EZGO golf cart?
The top speed of an EZGO golf cart is usually 19.9mph and the average speed is 14mph to 15mph. With governor adjustment, the EZGO cart can go faster by 5 to 10mph.
How to change the speed of a golf cart?
Locate the spring on the differential or carburetor that helps in changing the cart speed by adjusting its tension. Increase the length of the cable that is fitted on to the body of the throttle and clutch of the two-stroke engine.
How to ride a golf cart at full speed?
Ride the cart at full speed over a course of known length. This will ensure that the governor controls the speed of the cart within factory specifications. Fasten the black plastic cover and put the seat back in place. Take care when tightening the nut. The more you tighten, the faster your cart will go.
How to adjust a governor spring?
Loosen the adjusting locknut on the end of the governor spring. Rotate the locknut to expand or compress the spring until its length is 2 1/2 inches.
How to increase maximum governed speed?
Check manufacturer's specifications for the maximum governed speed and adjust the governor spring locknut if necessary. Tightening the spring locknut increases maximum governed speed, while loosening the locknut decreases maximum governed speed.
