Club Car DS throttle cable adjustment
- After setting the golf cart to neutral and maintenance mode, jack up the rear.
- Pull the spring that is present around the plastic piece located behind the shifter. Spin it until it falls back.
- Loosen the throttle cable present in the cable box to adjust the extent to which you can take it out of the housing.
- Press the accelerator so that the golf cart starts up and begins to idle. Check the cable tension to make sure that it’s still loose. ...
- Turn the key to the OFF position and put the cable back into the box.
- Adjust the cable tension so that the microswitch in the throttle box clicks just before the movement of the throttle plate begins.
- Turn the key to ON position and test if the adjustment is as desired. If not, repeat the above steps until you arrive at the preferred adjustment.
How do you bypass the throttle cable on a golf cart?
The throttle cable coming from the gas pedal generates a response to the spring-loaded linkage. This linkage is counteracted by the governor in the golf cart. If you want to bypass the governor, disconnect and reconnect the throttle cable once again without the intervening linkage.
How do I adjust the throttle cable?
The throttle cable adjustment can be done below the floor panel so that the engine gets started before the carburetor opens up. Adjust the rear cable from the governor arm to the gas pedal until the slack is almost nil.
How do I adjust the throttle on my EZ GO golf cart?
Just adjust the throttle idle screw until the engine runs but the cart does not move. Turn it in to increase the idle speed, and turn it out to slow and eventually stop the engine. Thanks! How do I install a throttle scale on my 2002 E Z Go golf cart?
What do you put on the throttle scale on a golf cart?
Depending on whether it has a power source to itself, if it has a personal power source, then just add duct tape or anything that will make it stay onto the 2002 EZ Go Golf Cart. And if the throttle scale doesn't, then just search it up.
How do I adjust the throttle cable on my golf cart?
0:005:15Yamaha G29 Drive Golf Cart Governor Adjustment - MORE SPEED!!YouTubeStart of suggested clipEnd of suggested clipHey guys i'm jonas today i'm going to show you how to adjust the governor. And the throttle cable onMoreHey guys i'm jonas today i'm going to show you how to adjust the governor. And the throttle cable on your yamaha g29 to get maximum. Speed. Now we do have the body removed from the back of this car
How do I adjust the accelerator cable?
0:302:18HOW TO ADJUST YOUR THROTTLE CABLE - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you can shift the outlet point of the cable to tighten. The cable itself and get rid of thatMoreAnd you can shift the outlet point of the cable to tighten. The cable itself and get rid of that slack you want just a small amount so that you're not stretching the cable.
How tight should accelerator cable?
1:031:48Throttle Cable Adjustment - Project Integra - YouTubeYouTubeStart of suggested clipEnd of suggested clipBasically just until it's taut you don't want to pull it.MoreBasically just until it's taut you don't want to pull it.
How do you adjust throttle cable tension?
2:205:41Adjusting Your Motorcycle Throttle and Why It's Important - YouTubeYouTubeStart of suggested clipEnd of suggested clipAs cracking the lock nut. Free. And then moving the barrel adjuster. And look if i push it back toMoreAs cracking the lock nut. Free. And then moving the barrel adjuster. And look if i push it back to the tension point and i'm dialing this back you can see that reference line is moving forward.
How can I make my throttle more responsive?
More air volume and speed is a surefire way to increase horsepower and throttle response at any given RPM. It is easy to achieve this at high RPM when the engine sucks in substantial amounts of air on its own. But coming off idle is another story.
What can a loose throttle cable cause?
Improper cable adjustment and slow acceleration response This can also result in the opposite effect as well, in that the excess slack can create a delayed throttle return response. This can cause more throttle to be applied unintentionally, creating a dangerous situation.
Should there be slack in throttle cable?
Most motorcycle manufacturers recommend about 2 to 3 millimeters of throttle free play, but over time the cables will stretch and settle into their housings and you'll end up with more slack.
How do I remove slack from throttle cable?
5:059:46HOW TO REMOVE THROTTLE CABLE SLACK - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what we need to do is to just to loosen these two screw the uh adjuster back up a bit take awayMoreSo what we need to do is to just to loosen these two screw the uh adjuster back up a bit take away that slack. And uh my throttle should be snatch free.
How to start a golf cart with a gas pedal?
Locate the gas pedal that is fitted to the governor and remove the connection. Re-route the gas pedal to the carburetor. Remove the bolt present on the shaft of the gas pedal. Slide the shaft upwards so that the gas pedal has more play. Tighten the bolt and start the golf cart.
How to change the speed of a golf cart?
Locate the spring on the differential or carburetor that helps in changing the cart speed by adjusting its tension. Increase the length of the cable that is fitted on to the body of the throttle and clutch of the two-stroke engine.
How Does a Golf Cart Governor Work?
A golf cart governor is a mechanical device that helps in controlling the maximum speed of the cart when it moves on flat ground. This device prevents the engine RPMs from increasing beyond the recommended specifications.
How to increase the speed of a cart?
Loosen the nut fitted on the cable. This will gradually increase the length of the cable. As the length increases, the speed of the cart will increase accordingly.
How fast is an EZGO golf cart?
The top speed of an EZGO golf cart is usually 19.9mph and the average speed is 14mph to 15mph. With governor adjustment, the EZGO cart can go faster by 5 to 10mph.
How to ride a golf cart at full speed?
Ride the cart at full speed over a course of known length. This will ensure that the governor controls the speed of the cart within factory specifications. Fasten the black plastic cover and put the seat back in place. Take care when tightening the nut. The more you tighten, the faster your cart will go.
How to adjust golf cart governor?
The governor on a golf cart can be adjusted easily by loosening the tension on its springs using a wrench or screwdriver to get the golf cart going at a relatively faster speed.
How to adjust low idle air on golf cart?
Position the golf cart to idle mode and set the low idle air adjustment according to your preference, for the engine to be able to pick up properly. This adjustment can be found on top of the carburetor. Often, two turns outward from the seated position is a good starting option.
When should a carburetor open up?
Check for full winding of the throttle spring present on the carburetor. It should open up fully when there is no load acting on it.
Why Do Carburetors Flood?
The reason why a carburetor floods on a golf cart is usually due to a faulty fuel pump.
What to do if needle valve is not seated properly?
Check if the needle valve is getting seated properly. If not, replace the entire assembly. Sometimes, the float may also have to be replaced.
What causes a carburetor to produce a lean mixture with insufficient fuel?
The engine starts overheating or backfiring that causes the carburetor to produce a lean mixture with insufficient fuel .
How many turns does a needle valve need to be in the outward direction?
Adjust the needle valve with 1-1/2 turns in the outward direction.
Where is the main jet on a 4-cycle engine?
The main jet in the carburetor diagram of a 4-cycle engine is located below the carburetor while the pilot jet is present on top of it. The needle valve and float pin are also housed under the carburetor.
How to raise the top speed of a golf cart?
To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly. If you cannot find this spring, you likely have a newer model that is more difficult to adjust, though this is rare. Lift up the seat. Remove the seat cousins, which hide the engine.
How to make a golf cart go faster?
Loosen the small nut and tighten the larger nut. The more you tighten the larger nut, the faster your cart will go. Start slowly, only tightening the nut a quarter turn to start. You can over-stress the engine if you try to run it too quickly, and it will skip and potentially burn out if you are too eager.
How to adjust EZ Go cart governor?
To adjust an EZ Go Cart Governor engine, start by removing the seat so that you can access the engine. Once the seat is off, remove the screws from the black plastic cover at the rear of the seat and then set the cover aside.
How to get a cart to move faster?
1. Remove the seat and plastic covering over the engine. Sometimes you'll need to remove screws while some models have seats that pop right out. Expose the engine so that you can get to work adjusting the motor. If you don't have a central governor spring, you can still get your cart to move a little faster.
How to tell if a gas pedal is a governor?
Follow the thickest cable coming from the gas pedal until your find a small spring wrapped around a metal rod. This is the governor. The spring apparatus will have two nuts, one small nut and one larger nut, holding it onto the rod.
How fast can a golf cart go?
Adjusting the governor can make your golf cart go 5–10 mph (8 .0–16.1 km/h) faster. If you do this to an E-Z-GO golf cart, you might be able to go from 15 mph (24 km/h) to 22 mph (35 km/h). It will only take about 5 minutes to do it. Steps.
How to change the speed of a car?
Locate your clutch pedal and line. The clutch is the pedal (sometimes a handle near your knee) that you use to put the car into reverse or change speeds. You can adjust the clutch to send more gas to your engine, moving you faster. ...
How to get to the engine on a golf cart?
Open up your golf cart’s access panel to get to the engine. In many cases, the panel pops open like a car hood, but in some instances you’ll need to unscrew the panel first.
How to adjust governor on a golf cart?
If you find this rod, then your governor can be easily adjusted by accessing the cart’s inner workings. Simply adjust the cable coming from this metal protrusion, turning the nut counterclockwise to make the cable longer, effectively adjusting the cart’s governance to increase the overall speed. If you cannot find external controls, you’ll need to adjust the governor internally.
Why are golf carts so popular?
In theory, golf carts make it easier for players to get across the course, saving their much-needed energy for the game. In practice, golf carts can be more of a nuisance than a help, as many standard carts creep along at unbearably slow speeds. Luckily, you don’t have to stick with these standard speeds. Golf cart speed is often controlled by a device called a governor, and you can adjust the governor on a golf cart relatively easily to make the cart faster.
How to loosen tension on a governor?
Use a screwdriver— or in some cases a wrench—to loosen the tension on the governor’s springs. You have now adjusted the governor for faster speed.
Who is the writer of GolfCarCatalog.com?
GolfCarCatalog.com – “Adjusting Your Golf Cart’s Governor”. Writer Bio. Richard Kalinowski began writing professionally in 2006. He also works as a website programmer and graphic designer for several clients.
Can you adjust the speed of a golf cart?
Luckily, you don’t have to stick with these standard speeds. Golf cart speed is often controlled by a device called a governor, and you can adjust the governor on a golf cart relatively easily to make the cart faster.