Club Car DS throttle cable adjustment
- After setting the golf cart to neutral and maintenance mode, jack up the rear.
- Pull the spring that is present around the plastic piece located behind the shifter. ...
- Loosen the throttle cable present in the cable box to adjust the extent to which you can take it out of the housing.
Full Answer
How to properly adjust throttle cables?
Club Car DS throttle cable adjustment. After setting the golf cart to neutral and maintenance mode, jack up the rear. Pull the spring that is present around the plastic piece located behind the shifter. Spin it until it falls back. Loosen the throttle cable present in the cable box to adjust the extent to which you can take it out of the housing.
How do you adjust throttle cable?
If more than 1", you need to adjust the throttle rod under the cart. It s the rod that connects the gas pedal to the black box. Loosen the nut on either end. Pull back on the spring tension part to release it from the ball. Unscrew it a few turns and pop it back on. Trial and error will get you to its perfect setting. Then tighten the nut up. 2.
How do you fix throttle cable?
Club Car DS Shift Cable Adjustment. The procedure for adjusting the shift cable in the club car DS is as follows (you can follow the manual if you have a copy). Ensure that the shift lever is in the neutral position. Loosen up the nuts to make minor adjustments. Once you have the cable in position, tighten the nuts and the job is done.
How do you adjust the governor on a club car?
Jun 16, 2018 · Jack up the rear. Put it in neutral and maintenance mode, pull the spring loaded round plastic piece behind the shifter back and spin it until it drops back in. Now loosen the throttle cable at the pedal box enough where you can slide it out of housing. Now push the pedal and the cart should start and idle.
How do you adjust the throttle on a Club Car golf cart?
0:493:44How to get your club car to idle - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust slightly that's the idle screw in. It. You have to turn it up just a hair I mean it's so littleMoreJust slightly that's the idle screw in. It. You have to turn it up just a hair I mean it's so little that you probably won't even notice it.
How do you adjust the throttle on a gas golf cart?
0:287:10Simple Adjusting of an E Z Go Golf Cart Governor - YouTubeYouTubeStart of suggested clipEnd of suggested clip90% of as go-karts have simple springs which limit the speed of the engine to raise the top speed ofMore90% of as go-karts have simple springs which limit the speed of the engine to raise the top speed of your golf cart all you need to do is locate the spring.
How do you adjust the governor on a club car?
0:040:46How to remove governor on a Club Car golf cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt looks up look inside. There's 12 cable down right here this lever you want to lift up and BendMoreIt looks up look inside. There's 12 cable down right here this lever you want to lift up and Bend and that pulls on the cable a little more.
Why does my gas golf cart backfire?
Engine backfiring occurs when there is an air leak within your golf cart or sometimes when there is too much fuel inside. This can cause the piston to slam against the cylinder head and cause a tapping sound. An essential component of any golf cart is the drive belt.
How do you adjust the governor on a Club Car gas golf cart?
If you find this rod, then your governor can be easily adjusted by accessing the cart's inner workings. Simply adjust the cable coming from this metal protrusion, turning the nut counterclockwise to make the cable longer, effectively adjusting the cart's governance to increase the overall speed.
How do you take the governor off a gas golf cart?
General InstructionsDetach the cable from the carburetor. The cable is about the width of a straw. ... Follow the disconnected cable up to the governor. ... Disconnect the gas pedal cable from the governor and reroute it to the carburetor. ... Using your wrench, remove the bolt on the gas pedal shaft.
Where is the governor on a Club Car golf cart?
0:061:28Where Is a Golf Cart Governor Located? - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell a golf cart's governor located is actually down in the motor. Compartment.MoreWell a golf cart's governor located is actually down in the motor. Compartment.
How do I change the speed on my club car?
1:1811:46Club Car precedent speed code 5 - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd it should take about 45 seconds first decide which speed you want to use.MoreAnd it should take about 45 seconds first decide which speed you want to use.
How do you set the speed on a golf cart?
Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.
How do I stop my golf cart from backfiring?
Find the nut holding the cable down and loosen it. Now, push the pedal down until you hear the click. Tighten the nut back up and you should have the proper timing for your throttle plate. Put your seat back on and ride your golf cart for awhile.
Why does my gas golf cart smoke?
The pistons on your golf cart help produce power by compressing your fuel and moving when the spark plug ignites the gas. However, these pistons can get broken or worn down and run improperly. When this happens, your cart is likely to produce a lot of excessive smoke whenever it runs.
How do you adjust the carburetor on a EZ Go golf cart?
2 Cycle engine: The adjustment screw is on the side of the carburetor and is parallel to the ground. You can identify it by the lock nut at the base of the screw. Loosen this and turn the screw all the way into a soft seat, then back it out one and a half (1-1/2) turns.Feb 25, 2021
How to adjust a golf cart?
If you are only making an adjustment to the shift cable, follow these steps: 1 Examine the shift cable closely for any damage. 2 If it is damaged you must go for a full replacement. 3 Do this inspection when the golf cart’s engine is off. 4 Allow the engine to cool before you do this exercise. 5 The adjustment has to be done at both ends. 6 One is the transaxle end and the other end is where you use the handle to shift R and F. 7 You should thoroughly clean the cable using a spray like WD40. 8 You can do the shift cable adjustment, with the shift lever in the forward position and then again changing it to the reverse position. This has been seen to be the better method in the Yamaha G2
How to adjust shift cable on Yamaha G20?
You can adjust the shift cable in the Yamaha G20 Gas by removing the adjustment nuts by slackening the jam nuts. Get the cables out by moving the shift lever back and forth. Now replace the cable and keep adjusting the cable-ending position at the transaxle end. They have to be of equal length.
Why is my Yamaha G9 not moving?
If you are facing the issue of the shift not working forward or reverse, it could be because a detent ball bearing may have fallen off during some other work on the transmission.