how to adjust throttle cable on ezgo golf cart

by Dr. Bart Pfannerstill Published 3 years ago Updated 2 years ago

How do you adjust the throttle cable on an EZGO golf cart?

Close the carburetor throttle plate..
Rotate the governor arm in a counter-clockwise direction..
Keep the cable inside the throttle cable bracket that is fitted on the rear axle..
Make sure that the governor and carburetor are seated with minimum slack and no tension..
Fix the cable in place by tightening the...

Full Answer

How do I adjust the throttle on my EZ GO golf cart?

How do you adjust the throttle cable on an EZGO golf cart? Close the carburetor throttle plate.. Rotate the governor arm in a counter-clockwise direction.. Keep the cable inside the throttle cable bracket that is fitted on the rear axle.. Make sure that the governor and carburetor are seated with ...

How do you adjust the throttle cable on a DS Golf cart?

Jun 26, 2020 · Just adjust the throttle idle screw until the engine runs but the cart does not move. Turn it in to increase the idle speed, and turn it out to slow and eventually stop the engine. In respect to this, how do you adjust the throttle cable on a EZ Go golf cart? To adjust the throttle cable, check to ensure carburetor throttle plate is fully closed and governor arm is rotated fully …

How do I adjust the shift cable on the E-Z-GO TXT?

Keep the shift in neutral and then adjust the cable. The play given is 1 3/8-inch and it goes till the end of the threaded portion. You will have to include the thickness of the nut for this measurement. E-Z-GO RXV Shift Cable Adjustment You may be in two situations. One is fixing a new set of cables for the E-Z-GO RXV cabling for the shift.

What does a throttle cable do on a golf cart?

Mar 24, 2015 · Link to part on our website: http://www.diygolfcart.com/EZGO-Throttle-Cable-p/cbl-051(6429).htmLearn how to adjust your governor or throttle cable on an EZGO...

How do I adjust the speed on my EZ Go golf cart?

Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.

How do I adjust the throttle cable on free play?

Adjusting Throttle Free Play:

If your free play is out by a small amount, use the inline adjuster at the handlebars: simply loosen the locknut, and turn the barrel adjuster until the movement of the grip is in the specified range.Apr 12, 2021

How do I increase the speed of my EZ Go TXT?

6 Ways You Can Make a Golf Cart Faster

Add More Torque to Your Golf Cart.
Upgrade Your Golf Cart's Motor.
Improve the High-Speed Controller of the Cart.
Add Better Golf Cart Tires.
Use a Higher Powered Golf Cart Battery.
Watch the Weight in Your Golf Cart.

May 18, 2021

How do I adjust the throttle cable?

Difficulty

Open your hood and locate your engine's throttle body. ...
Remove the air intake duct at the throttle body.
Inspect the throttle body ports for carbon build up. ...
Remove the throttle cable from the throttle body control lever. ...
Disconnect any air or vacuum hoses from the throttle body.

More items...

How do you fix a tight throttle cable?

In order to fix a loose or tight throttle cable, you'll need to turn this nut. Place the open ended wrench over the throttle body adjustment nut, and turn the nut either clockwise or counterclockwise until there is about 1/4 inch play in the tension of the throttle cable.

How do you adjust a push pull throttle cable?

Part of a video titled How To Adjust Throttle Cables Like A Pro - YouTube

6:36

9:25

You have a lock nut you can break that loose. And you can back this out. So when you back it out youMoreYou have a lock nut you can break that loose. And you can back this out. So when you back it out you are pulling that tension tighter.

Is 30 mph fast for a golf cart?

Depending on how far you want to go on a full charge, you might want a 40mph or a 30mph golf cart. At top speed, most golf carts do around 14mph. However, with the advent of street legal golf carts and modifications, it is possible to go 35mph and above.Oct 4, 2021

How can I make my golf cart gas faster?

Increase the RPM

An increase in the input shaft rpm for all differential ratios will produce a higher speed. For a gas golf cart, other than adjusting the governor, the speed may be enhanced by replacing the engine with a higher rpm output model.Apr 3, 2018

Why is my gas golf cart running slow?

Low Battery

Usually, the most common reason golf carts slow down is when they don't get enough power output from the battery. If the battery pack charge is very low and your cart is out of power, your cart will run slow.Jul 14, 2021

How can I make my throttle more responsive?

Easy ways to get ride of throttle delay is by making sure you keep up with basic maintenance like change fluids, air filter, fuel filter, tire pressure which all help to improve speed, fuel economy. Making sure you have clean fuel filter will help improve fuel economy, speed, and rpm at various shift points.Jun 5, 2021

What does adjusting the throttle cable do?

The tightness of the accelerator, or throttle, cable on any vehicle is important. If the cable is tightened too much, the car will not idle properly and consume fuel quickly. If the cable is too loose, the car will respond slowly when you press the gas pedal.

How much slack should a throttle cable have?

about 2 to 3 millimeters

Most motorcycle manufacturers recommend about 2 to 3 millimeters of throttle free play, but over time the cables will stretch and settle into their housings and you'll end up with more slack.Feb 12, 2020

How to adjust a golf cart?

If you are only making an adjustment to the shift cable, follow these steps: 1 Examine the shift cable closely for any damage. 2 If it is damaged you must go for a full replacement. 3 Do this inspection when the golf cart’s engine is off. 4 Allow the engine to cool before you do this exercise. 5 The adjustment has to be done at both ends. 6 One is the transaxle end and the other end is where you use the handle to shift R and F. 7 You should thoroughly clean the cable using a spray like WD40. 8 You can do the shift cable adjustment, with the shift lever in the forward position and then again changing it to the reverse position. This has been seen to be the better method in the Yamaha G2

How far is the shift cable on a golf cart?

A golf cart shift cable adjustment is 1 3/8-inch from the washer and is to be made till the end of the threads. The adjuster has to be in the neutral position while making this change in the cable’s position.

How to adjust shift cable on Yamaha G20?

You can adjust the shift cable in the Yamaha G20 Gas by removing the adjustment nuts by slackening the jam nuts. Get the cables out by moving the shift lever back and forth. Now replace the cable and keep adjusting the cable-ending position at the transaxle end. They have to be of equal length.

Why is my Yamaha G9 not moving?

If you are facing the issue of the shift not working forward or reverse, it could be because a detent ball bearing may have fallen off during some other work on the transmission.

Can you replace the shift cable on a Yamaha G2?

You have to access the transaxle on the rear of the cart and pull out the bracket where the cables are attached. You can now replace the cable. Remember to mark the location of the bracket on the vehicle before pulling it out.

What happens if you don't adjust your golf cart?

If there's no adjustment left the cable must be stretched. As long as you're getting full throttle and the golf cart is running fine at slower speeds I wouldn't worry about it.

Does the butterfly carburetor need to be adjusted?

No it sounds like the cable needs to be adjusted. The carburetor butterfly should start to open right after the micro switch activates and should close just before the micro switch clicks.

How to adjust EZ Go cart governor?

To adjust an EZ Go Cart Governor engine, start by removing the seat so that you can access the engine. Once the seat is off, remove the screws from the black plastic cover at the rear of the seat and then set the cover aside.

How to raise the top speed of a golf cart?

To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly. If you cannot find this spring, you likely have a newer model that is more difficult to adjust, though this is rare. Lift up the seat. Remove the seat cousins, which hide the engine.

How to make a golf cart go faster?

Loosen the small nut and tighten the larger nut. The more you tighten the larger nut, the faster your cart will go. Start slowly, only tightening the nut a quarter turn to start. You can over-stress the engine if you try to run it too quickly, and it will skip and potentially burn out if you are too eager.

How to get a cart to move faster?

1. Remove the seat and plastic covering over the engine. Sometimes you'll need to remove screws while some models have seats that pop right out. Expose the engine so that you can get to work adjusting the motor. If you don't have a central governor spring, you can still get your cart to move a little faster.

How to tell if a gas pedal is a governor?

Follow the thickest cable coming from the gas pedal until your find a small spring wrapped around a metal rod. This is the governor. The spring apparatus will have two nuts, one small nut and one larger nut, holding it onto the rod.

How fast can a golf cart go?

Adjusting the governor can make your golf cart go 5–10 mph (8 .0–16.1 km/h) faster. If you do this to an E-Z-GO golf cart, you might be able to go from 15 mph (24 km/h) to 22 mph (35 km/h). It will only take about 5 minutes to do it. Steps.

How to change the speed of a car?

Locate your clutch pedal and line. The clutch is the pedal (sometimes a handle near your knee) that you use to put the car into reverse or change speeds. You can adjust the clutch to send more gas to your engine, moving you faster. ...

Why is the brake on my golf cart not working?

Basically, to get safe from any dangerous situation one must adjust the break after sometimes. As time passes and a golf cart gets old the brakes of the golf carts also gets weaken. The break shoe or the brake pad gets worn out or gets loosen. Therefore the brake seems to be not working perfectly. One cannot pull the break of the cart right on time which can be very dangerous. Therefore brake adjustment is crucial.

Why are golf carts so slow?

Because these vehicles are made to reduce the effort of the golfers and safely take the golfers to their suitable area. For their slow speed, there is no risk of major accidents.

Why does my golf cart get overturned?

Sometimes it seems that on these slope areas cart drivers are not able to stop the cart properly and the cart gets overturned. This happens because of over speed and the failure of the brake's ability. It can cause serious injuries to the driver and also to the golfers. Therefore proper adjustment of the breaks is needed.

Do golf carts need a break?

Different manufacturers use different mechanisms to make their golf carts. Some golf carts have their auto adjustable brake mechanism. These types of carts do not need their break to be adjusted.

Is an electric golf cart faster than a gas golf cart?

Generally, electric golf carts are slower than gas powered golf carts. But sometimes it seems that the EZGO golf carts are far slower than before. There are many reasons for it. Here are some reasons that will reduce the speed of the EZ-GO golf cart.

How to compress clutch cable?

Compress the cable by hand trying to bring these rubber ears as close to each other as possible. Once this is done, use a wire and wrap the wire around both ears as this will prevent the cable from decompressing. Might have to compress it by the pedal itself, but should be able to do it by hand. When u wrap the wire, do it in a figure 8 fashion because u have to get all 4 rubber ears otherwise the cable will decompress on one side.

Why does my car battery move in reverse?

The reason it will barely move in reverse is that current is being supplied to the motor is a direction that it spends very little time using . There is a slight change in the armature over time, and reverse tends to work better over time.

Golf-FAQ.com