- Back out the throttle stop screw so that the butterfly isn't open too much. ...
- Tighten the nut that is at the end of the lever above the transaxle as much as possible. ...
- Adjust the rear cable from the governor arm to the gas pedal until the slack is almost nil.
How do you adjust the governor on a Yamaha G2 golf cart?
The following methods show you how to adjust the governor on your Yamaha G2 golf cart. Locate the lever present above the transaxle. This lever houses a 10mm nut. Tighten the nut or move it inwards as much as you want based on the desired speed using a 1/4″ drive ratchet with a 10mm deep socket.
How do you adjust the shift cable on a Yamaha G2?
Yamaha G2 Shift Cable Adjustment With the Yamaha G2, the shift cable adjustment is not a very difficult one. You have to access the transaxle on the rear of the cart and pull out the bracket where the cables are attached. You can now replace the cable.
How do you adjust the carburetor on a Yamaha golf cart?
How to Adjust Yamaha Golf Cart Carburetor Yamaha G9 Carburetor Adjustment. Pull out the pilot adjustment screw. It must be present at a sharp point and not a flat spot. Rethread the screw back until it’s slightly seated. Turn the screw outwards by 1-1/2 turns. Push the throttle stop screw backward until the throttle shaft is closed completely.
How do I adjust the throttle cable on my electric golf cart?
Ensure that the throttle plate is closed fully and the governor arm is rotated in the counter-clockwise direction completely. Loosen the nut that is near the throttle cable bracket and positioned towards the back of the cart.
How do you adjust the throttle on a gas golf cart?
0:287:10Simple Adjusting of an E Z Go Golf Cart Governor - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne Titan the governor spring located in the engine of most golf carts to adjust your carts topMoreOne Titan the governor spring located in the engine of most golf carts to adjust your carts top speed. 90% of as go-karts have simple springs which limit the speed of the engine to raise the top speed
How do you adjust throttle control cable?
0:262:18HOW TO ADJUST YOUR THROTTLE CABLE - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you can shift the outlet point of the cable to tighten. The cable itself and get rid of thatMoreAnd you can shift the outlet point of the cable to tighten. The cable itself and get rid of that slack you want just a small amount so that you're not stretching the cable.
How do you adjust the governor on a Yamaha g2 golf cart?
0:004:32Yamaha Drive 2 Quietech Governor Adjustment - GET MORE SPEEDYouTubeStart of suggested clipEnd of suggested clipSo sometimes as you're pulling up you need to hit down on the body on each side to release thoseMoreSo sometimes as you're pulling up you need to hit down on the body on each side to release those clips. And then there's just two tabs that slide in in the front.
What can a loose throttle cable cause?
Some of these issues are:The pedal feels stiff or hard to depress.The pedal sticks and does not release normally.There is slack in the pedal's movement.There is a rough or abnormally low idle.The engine stalls.There is a delay in response when you push the pedal down.More items...•
How do you adjust the throttle cable on a Yamaha golf cart?
Yamaha G16 throttle cable adjustment Adjust the throttle cable from the governor to the carburetor by turning the governor lever in the counterclockwise fully. Ensure that the carburetor throttle valve is open fully. If not, turn the adjustment nuts either inwards or outwards to adjust the throttle cable.
How tight should the throttle cable be?
The accelerator cable tension is usually set so that 2-3mm of free play is present in the throttle grip. Once the correct tension has been applied, the lock nuts should be snugged and any dust covers should be slid back over the adjusters. Cables can be adjusted using the appropriate size wrench.
Where is the governor on a Yamaha golf cart?
The governor generally sits on top of the engine. This is the easiest way to find the carburetor. Once you've followed the cable up to the governor spring, disconnect it there as well.
What does removing the governor do?
Removing the governor will increase the maximum rpm of the engine, but the internal parts of the Predator 212 are designed for 3600 rpm. Generally, this isn't an issue with just the governor removal, the internal parts can usually withstand 5000 rpm without breaking apart (unless you go full throttle for too long).
How do you make a golf cart go faster?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
How do you know if you have a bad throttle cable?
Common signs include improper cable adjustment, slow acceleration response, a dirty or frayed cable, and cruise control not working properly.
How do I check my throttle cable?
Step 1: Locate the throttle cable. One end of the throttle cable is located in the engine compartment, attached to the throttle body. The other end is on the driver's side floor, attached to the accelerator pedal.
How do you know if you need a new throttle cable?
If you notice any sudden changes in tension from the pedal, such as jerking or binding when you activate the cruise control, then that may be sign that there may be a problem with the accelerator cable. As both cables are connected to the same throttle body, any problems with the operation of one can affect the other.
How to adjust shift cable on golf cart?
If you are only making an adjustment to the shift cable, follow these steps: Examine the shift cable closely for any damage. If it is damaged you must go for a full replacement. Do this inspection when the golf cart’s engine is off. Allow the engine to cool before you do this exercise.
How to adjust a golf cart?
If you are only making an adjustment to the shift cable, follow these steps: 1 Examine the shift cable closely for any damage. 2 If it is damaged you must go for a full replacement. 3 Do this inspection when the golf cart’s engine is off. 4 Allow the engine to cool before you do this exercise. 5 The adjustment has to be done at both ends. 6 One is the transaxle end and the other end is where you use the handle to shift R and F. 7 You should thoroughly clean the cable using a spray like WD40. 8 You can do the shift cable adjustment, with the shift lever in the forward position and then again changing it to the reverse position. This has been seen to be the better method in the Yamaha G2
Why is my Yamaha G9 not moving?
If you are facing the issue of the shift not working forward or reverse, it could be because a detent ball bearing may have fallen off during some other work on the transmission.
Can you replace the shift cable on a Yamaha G2?
You have to access the transaxle on the rear of the cart and pull out the bracket where the cables are attached. You can now replace the cable. Remember to mark the location of the bracket on the vehicle before pulling it out.
How to start a golf cart with a gas pedal?
Locate the gas pedal that is fitted to the governor and remove the connection. Re-route the gas pedal to the carburetor. Remove the bolt present on the shaft of the gas pedal. Slide the shaft upwards so that the gas pedal has more play. Tighten the bolt and start the golf cart.
How to change the speed of a golf cart?
Locate the spring on the differential or carburetor that helps in changing the cart speed by adjusting its tension. Increase the length of the cable that is fitted on to the body of the throttle and clutch of the two-stroke engine.
How fast is an EZGO golf cart?
The top speed of an EZGO golf cart is usually 19.9mph and the average speed is 14mph to 15mph. With governor adjustment, the EZGO cart can go faster by 5 to 10mph.
What is a golf cart governor?
A golf cart governor is a mechanical device that helps in controlling the maximum speed of the cart when it moves on flat ground. This device prevents the engine RPMs from increasing beyond the recommended specifications.
How to ride a golf cart at full speed?
Ride the cart at full speed over a course of known length. This will ensure that the governor controls the speed of the cart within factory specifications. Fasten the black plastic cover and put the seat back in place. Take care when tightening the nut. The more you tighten, the faster your cart will go.
Where is the governor arm on a golf cart?
Locate the governor arm of the golf cart. This is mounted above the rear axle housing and under the cart. Depending on the cart model, there may be a protection plate above the governor.
Can you remove a golf cart governor?
It doesn’t take much time or skill to remove a golf cart governor. With some basic mechanical expertise and general-purpose tools, you can do this yourself. The process is more or less the same in all golf carts.
Jean Leblanc
look above the clutch cable the is a rubber boot, abot 8-10 inches long. If u notice on either end of this boot are rubber prongs, or ears or whatever u wanna call em. Compress the cable by hand trying to bring these rubber ears as close to each other as possible.
Anonymous
Go to http://www.hmaservice.com/ and register the vehicle (By VIN). Afterward you'lll have access to manuals, wiring diagrams, service bulletins, etc. Good Luck.
Anonymous
Try loosening the nut for the cable. Shift into park from under hood. Put shifter in park and pull cable, push nut towards cable and tighten nut.
How to adjust carburetor on golf cart?
In most cases, you’ll need to adjust the jet pilot screw, perform a valve clearance adjustment and then clean the carburetor.
How to remove cable from carburetor?
Remove the cable from the carburetor and cover its sheath opening using duct tape. To do this, make a small funnel with the tape and ensure that the wire sticks out from its middle. Loosen the nut that fixes the cable on to the mount housed on the motor just before its entry into the carburetor.
How to replace carburetor float?
Remove the carburetor and turn it upside down. Remove the nut that is used to secure the bowl on. Check the float for a puncture as this prevents the activation of the fuel cut-off needle valve. Replace the float if there is a puncture. Check for dirt accumulation in the needle valve.
Why does an EFI carb require more maintenance than an EFI?
The carb requires more maintenance than an EFI because of the cleaning and rebuilding of the carburetor involved.
Why does my carburetor flood on my golf cart?
The reason why a carburetor floods on a golf cart is usually due to a faulty fuel pump. The pump must be repaired or replaced accordingly. Seek professional assistance if required. This is usually due to the proximity of the fuel line to an exhaust manifold, a radiator hose or a heat source.
How to cool down a golf cart?
Procedure. Turn off the golf cart engine and allow it to cool for a couple of hours before you start working. This cooling down prevents damage to the cart and injury to yourself when you’re at work. Turn off the fuel-supply valve and remove the fuel line to prevent flooding of the fuel and other complications.
Where is the main jet on a 2 cycle engine?
The main jet in the carburetor diagram of a 4-cycle engine is located below the carburetor while the pilot jet is present on top of it. The needle valve and float pin are also housed under the carburetor.