How do you adjust the throttle cable on an EZGO golf cart?
- Close the carburetor throttle plate..
- Rotate the governor arm in a counter-clockwise direction..
- Keep the cable inside the throttle cable bracket that is fitted on the rear axle..
- Make sure that the governor and carburetor are seated with minimum slack and no tension..
- Fix the cable in place by tightening the...
How do you adjust the throttle cable on an EZGO golf cart?
How do you adjust the throttle cable on an EZGO golf cart? Close the carburetor throttle plate.. Rotate the governor arm in a counter-clockwise direction.. Keep the cable inside the throttle cable bracket that is fitted on the rear axle.. Make sure that the governor and carburetor are seated with ...
How do you adjust the throttle cable on a carburetor?
Bypass the governor and connect the throttle cable to the carburetor directly. Before adjusting both the throttle cables, you must turn the main switch OFF. Block the wheels and take off the rear access panel. Adjust the throttle cable from the governor to the carburetor by turning the governor lever in the counterclockwise fully.
What does a throttle cable do on a golf cart?
It ensures that your golf cart operation is smooth and safe. A throttle cable assists in the efficient utilization of the batteries and gas of the golf cart. How do you adjust the throttle cable on an EZGO golf cart?
How do I adjust the top speed of my golf cart?
It will only take about 5 minutes to do it. Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.
How do you adjust the throttle on a EZ Go golf cart?
1:005:06How to Adjust an E Z Go Golf Cart Governor - WikiVideo - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you are curious this is your carts carburetor loosen the small nut and tighten the larger nut.MoreIf you are curious this is your carts carburetor loosen the small nut and tighten the larger nut. The more you tighten the larger nut the faster your cart will.
How do you change the speed on a ezgo gas golf cart?
Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.
How do you adjust the carburetor on a EZ Go golf cart?
2 Cycle engine: The adjustment screw is on the side of the carburetor and is parallel to the ground. You can identify it by the lock nut at the base of the screw. Loosen this and turn the screw all the way into a soft seat, then back it out one and a half (1-1/2) turns.
How do you adjust the governor on a golf cart?
Adjusting an EZ-GO Golf Cart GovernorStep 1 - First, lift the seat of your engine to reveal seat cousins. ... Step 2 - Remove the seat cushions over your motor. ... Step 3 - Remove the black plastic cover to expose the motor. ... Step 4 - Loosen the smaller one and tighten the larger one to increase your cart's speed.More items...•
Where is the speed controller on an ezgo golf cart?
Flip the maintenance switch All EZ-GO speed controllers are equipped with a maintenance switch that needs to be flipped before you begin work on repairing the problem. You will likely find the switch under the seat of your golf car,t but if you're having trouble finding it, consult your owner's manual.
Why is my ezgo golf cart so slow?
A EZGO RXV and TXT golf cart can run slow because of a faulty speed sensor, low battery charge and insufficient levels of water in the battery. A problem with the speed sensor. A faulty speed magnet. One or more batteries could are weak and don't have sufficient charge or the water level could be low.
Why is my gas golf cart slow?
Low Battery Usually, the most common reason golf carts slow down is when they don't get enough power output from the battery. If the battery pack charge is very low and your cart is out of power, your cart will run slow.
How do you adjust a carburetor on a gas golf cart?
Find the pilot adjustment screw on the edge of your carburetor. Pay attention to this screw – it should be a sharp point and not flat. Carefully remove this screw and then carefully screw it back. Turn this screw out one and one-half turns to adjust it properly.
What causes golf cart hesitation?
In most cases, the hesitation problem occurs due to bad batteries. If you have bought new batteries for your EZGO RXV, make sure to fully charge them before the first use. Batteries should then be charged after every use. To keep the batteries in check, get a Digital MultiMeter to measure the individual voltage.
How can I increase the speed of my golf cart?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
Where is the governor on a golf cart?
0:101:28Where Is a Golf Cart Governor Located? - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell a golf cart's governor located is actually down in the motor. Compartment. Some of them theseMoreWell a golf cart's governor located is actually down in the motor. Compartment. Some of them these electric ones nowadays. Actually the governor isn't a true governor. It is a control speed.
How do you take the governor off a EZ Go golf cart?
General InstructionsDetach the cable from the carburetor. The cable is about the width of a straw. ... Follow the disconnected cable up to the governor. ... Disconnect the gas pedal cable from the governor and reroute it to the carburetor. ... Using your wrench, remove the bolt on the gas pedal shaft.
How to adjust EZ Go cart governor?
To adjust an EZ Go Cart Governor engine, start by removing the seat so that you can access the engine. Once the seat is off, remove the screws from the black plastic cover at the rear of the seat and then set the cover aside.
How to raise the top speed of a golf cart?
To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly. If you cannot find this spring, you likely have a newer model that is more difficult to adjust, though this is rare. Lift up the seat. Remove the seat cousins, which hide the engine.
How to make a golf cart go faster?
Loosen the small nut and tighten the larger nut. The more you tighten the larger nut, the faster your cart will go. Start slowly, only tightening the nut a quarter turn to start. You can over-stress the engine if you try to run it too quickly, and it will skip and potentially burn out if you are too eager.
How to get a cart to move faster?
1. Remove the seat and plastic covering over the engine. Sometimes you'll need to remove screws while some models have seats that pop right out. Expose the engine so that you can get to work adjusting the motor. If you don't have a central governor spring, you can still get your cart to move a little faster.
How fast can a golf cart go?
Adjusting the governor can make your golf cart go 5–10 mph (8 .0–16.1 km/h) faster. If you do this to an E-Z-GO golf cart, you might be able to go from 15 mph (24 km/h) to 22 mph (35 km/h). It will only take about 5 minutes to do it. Steps.
How many screws are in a golf cart engine?
There should be five screws in most models. The engine is in the front of golf carts, underneath this panel. Take off the plastic cover and set it aside with the seats. ...
How to change the speed of a car?
Locate your clutch pedal and line. The clutch is the pedal (sometimes a handle near your knee) that you use to put the car into reverse or change speeds. You can adjust the clutch to send more gas to your engine, moving you faster. ...
What happens if you don't adjust your golf cart?
If there's no adjustment left the cable must be stretched. As long as you're getting full throttle and the golf cart is running fine at slower speeds I wouldn't worry about it.
Does the butterfly carburetor need to be adjusted?
No it sounds like the cable needs to be adjusted. The carburetor butterfly should start to open right after the micro switch activates and should close just before the micro switch clicks.
For the 295cc or a 350cc twin-cylinder OHC engine. 1991 – Present
Tools required: Ratchet with 6″ extension, 10mm socket, 10mm socket wrench, flat blade screwdriver, and a feeler gauge. Note: if the screw (C) has a square head instead of a flat blade slot, this takes a tool designed just for this purpose.
For the Kawasaki FJ400 401cc 4-cycle Single Cylinder 1996 – Present
Tools required: Ratchet with 6″ extension, 10mm socket, 3mm hex wrench, feeler gauge.
Do E-Z-Go Golf Carts have titles?
E-Z-Go Golf Carts, unlike vehicles, do not have a title, but they do have serial numbers. If you are buying a golf cart, it is essential to check the serial number to ensure you do not buy a stolen one. Each E-Z-Go Golf cart has a unique serial number that you can use to identify your golf cart.
Where is the E-Z-Go Cart Serial Number
As mentioned above, all E-Z-Go Golf carts have unique serial numbers. These numbers are essential when buying replacement parts for your golf cart. Textron Specialized Vehicles has been building golf carts for a long time, and the serial numbers are placed on different parts of the golf carts.
How do I push my E-Z-Go Golf Cart?
It can be frustrating when your battery is flat and your golf cart will not roll. To push it to the nearest charging or gas station, you need to release the motor brake. Follow these easy steps to do that.
Why does my E-Z-Go golf cart not move
There are several reasons why your cart refuses to move, but you should check the battery before anything else. If the battery is charged, here are some other reasons why your golf cart will not move.
Are all E-Z-Go Golf carts electric?
No, there are both electric and gas-powered E-Z-Go Golf carts available. Bear in mind that there are several models you can drive on the street, but those are all-electric. These electric models run on batteries that you have to charge at least every 24 hours, depending on how much you use them.
How to tell the Assembly year of my E-Z-Go golf cart
The placement of serial numbers is discussed above, and you will find the manufacturer’s number right next to it. The manufacturer’s number consists of one letter and 3 or 4 numbers. The last two numbers indicate the last two digits of the year of assembly.
How to service E-Z-Go Golf Cart
Like all vehicles, E-Z-Go golf carts require regular maintenance to enhance longevity and performance. You should ensure that your golf cart is serviced after every six months of use. That will ensure that you spot problems and repair them early, which will help reduce repair costs. Here are essential guidelines for E-Z-Go golf cart maintenance.
How to adjust a golf cart?
If you are only making an adjustment to the shift cable, follow these steps: 1 Examine the shift cable closely for any damage. 2 If it is damaged you must go for a full replacement. 3 Do this inspection when the golf cart’s engine is off. 4 Allow the engine to cool before you do this exercise. 5 The adjustment has to be done at both ends. 6 One is the transaxle end and the other end is where you use the handle to shift R and F. 7 You should thoroughly clean the cable using a spray like WD40. 8 You can do the shift cable adjustment, with the shift lever in the forward position and then again changing it to the reverse position. This has been seen to be the better method in the Yamaha G2
How to adjust shift cable on golf cart?
If you are only making an adjustment to the shift cable, follow these steps: Examine the shift cable closely for any damage. If it is damaged you must go for a full replacement. Do this inspection when the golf cart’s engine is off. Allow the engine to cool before you do this exercise.
Why is my Yamaha G9 not moving?
If you are facing the issue of the shift not working forward or reverse, it could be because a detent ball bearing may have fallen off during some other work on the transmission.
Can you replace the shift cable on a Yamaha G2?
You have to access the transaxle on the rear of the cart and pull out the bracket where the cables are attached. You can now replace the cable. Remember to mark the location of the bracket on the vehicle before pulling it out.
