If the ignition timing is incorrect, adjust it in accordance with the following procedures. I. Remove the cooling fan shroud and cooling fan, and loosen the plate mounting screws. 2. Adjust the timing by rotating the plate - left or right.
Full Answer
How do you adjust the speed on an EZ GO golf cart?
Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.
When should I replace the coil on my EZGO golf cart?
If outside the range, the coil should be replaced. Pulser coils can be fried, and the only way to start a EZGO golf cart is by replacing the coil. You can test the coil and use follow the below steps to remove and install a new one.
How do I tune-up my E-Z-Go gasoline engine?
These are the easy steps to perform a basic tune-up on your E-Z-Go gasoline engine using a minimum of tools and an optional tune-up kit. As always, we begin with the three basics…Air, fuel, spark. Unsure of your year and model?
How do you test a Pulser coil on an EZGO golf cart?
How to test a pulser coil on an EZGO golf cart A voltmeter can be used to test the pulser coil or the igniter of a golf cart. This will tell you if the coils are damaged or there is some other larger problem hidden underneath the golf cart. Check the user manual to know the exact location of the pulser coil under the seat.
How do I set the time on my EZGO golf cart?
0:091:50EZGO 350cc eh35c Timing engine - YouTubeYouTubeStart of suggested clipEnd of suggested clipSee this is how you time the engine take this dot. Make sure it's lined up with this groove. ThisMoreSee this is how you time the engine take this dot. Make sure it's lined up with this groove. This little notch here come down to this this little gear here.
How can I make my EZGO golf cart faster?
One way to increase the speed of EZ Go golf carts is to incorporate an octane booster when you fill the tank. The cart will have more pick-up, and it could gain as much as 5 mph. A different approach is to take out the throttle linkage governor on the carburetor.
How do you adjust the governor on a EZGO electric golf cart?
0:545:06How to Adjust an E Z Go Golf Cart Governor - WikiVideo - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake off the plastic cover and set it aside with the seats. Follow the thickest cable coming fromMoreTake off the plastic cover and set it aside with the seats. Follow the thickest cable coming from the gas pedal until your find a small spring wrapped around a metal rod. This is the governor.
How do you adjust the carburetor on a EZGO golf cart?
2 Cycle engine: The adjustment screw is on the side of the carburetor and is parallel to the ground. You can identify it by the lock nut at the base of the screw. Loosen this and turn the screw all the way into a soft seat, then back it out one and a half (1-1/2) turns.
Why is my golf cart so slow?
Low Battery Usually, the most common reason golf carts slow down is when they don't get enough power output from the battery. If the battery pack charge is very low and your cart is out of power, your cart will run slow.
How do you speed up a 36 volt EZ Go golf cart?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
Where is the speed controller on an ezgo golf cart?
These speed controllers are located under the EZGO cart seat. Check the speed controller's attachment near the carburetor.
How can I make my electric golf cart go faster without upgrading?
How to Make an Electric Golf Cart Faster Without UpgradesWash Your Cart Properly. ... Inspect the Batteries. ... Refill the Battery Water. ... Check the Gas Pedal and Linkage. ... Measure the Tire Pressure. ... Charge Up Your Battery Unit. ... Lighten Up Your Cart's Weight.
What causes a golf cart to backfire?
Engine backfiring occurs when there is an air leak within your golf cart or sometimes when there is too much fuel inside. This can cause the piston to slam against the cylinder head and cause a tapping sound. An essential component of any golf cart is the drive belt.
How do you adjust the throttle on a golf cart?
Pull the spring that is present around the plastic piece located behind the shifter. Spin it until it falls back. Loosen the throttle cable present in the cable box to adjust the extent to which you can take it out of the housing. Press the accelerator so that the golf cart starts up and begins to idle.
Why does my golf cart only run with the choke on?
Dwight Coleman there are usually only a few possibilities if it only runs with the choke. One cause could be an air leak on the carb, head gasket, crankshaft seal. The other could be a clogged low speed and idle circuit.
Why do I have to choke my golf cart?
A golf cart choke is commonly used when starting a cold engine to restrict air flow while the fuel gets to the engine. Once the mixture stabilizes and the engine can run on its own without air restriction, the choke is released.
How to adjust EZ Go cart governor?
To adjust an EZ Go Cart Governor engine, start by removing the seat so that you can access the engine. Once the seat is off, remove the screws from the black plastic cover at the rear of the seat and then set the cover aside.
How to raise the top speed of a golf cart?
To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly. If you cannot find this spring, you likely have a newer model that is more difficult to adjust, though this is rare. Lift up the seat. Remove the seat cousins, which hide the engine.
How to make a golf cart go faster?
Loosen the small nut and tighten the larger nut. The more you tighten the larger nut, the faster your cart will go. Start slowly, only tightening the nut a quarter turn to start. You can over-stress the engine if you try to run it too quickly, and it will skip and potentially burn out if you are too eager.
How to get a cart to move faster?
1. Remove the seat and plastic covering over the engine. Sometimes you'll need to remove screws while some models have seats that pop right out. Expose the engine so that you can get to work adjusting the motor. If you don't have a central governor spring, you can still get your cart to move a little faster.
How fast can a golf cart go?
Adjusting the governor can make your golf cart go 5–10 mph (8 .0–16.1 km/h) faster. If you do this to an E-Z-GO golf cart, you might be able to go from 15 mph (24 km/h) to 22 mph (35 km/h). It will only take about 5 minutes to do it. Steps.
How many screws are in a golf cart engine?
There should be five screws in most models. The engine is in the front of golf carts, underneath this panel. Take off the plastic cover and set it aside with the seats. ...
How to change the speed of a car?
Locate your clutch pedal and line. The clutch is the pedal (sometimes a handle near your knee) that you use to put the car into reverse or change speeds. You can adjust the clutch to send more gas to your engine, moving you faster. ...
Step 1: Air filter
The canister air filter is accessed by raising and lifting out the cart seat, locating the cylindrically shaped airbox with a cap on the end, and unsnapping the two holding clips on each side. Remove the lid and then the filter.
Step2: Spark Plugs
The recommended spark plugs are manufactured by NGK, number NGK BPR4ES. Locate the spark plug (s) on the top of the engine and remove the cable, exposing the top of the plug. Use a spark plug socket and ratchet to remove the spark plug and inspect the ceramic insulator.
Step 3: Fuel
The fuel filter is located in line between the fuel tank and the fuel pump. If the housing is clear plastic, make sure that the fuel inside is not dark amber or discolored from age.
Step 4: Valve Adjustment
Check and adjust the valves every 250 hours or every year To keep the engine starting and running properly.
Conclusion
All of these adjustments can be made on your EzGo Golf Cart without spending anything more than your time, BUT if any of the components are damaged, such as the gaskets, plugs or if the filters are too far gone to blow the dirt out of them, it is time to open the old wallet.
How to increase speed of EZ Go golf cart?
One way to increase the speed of EZ Go golf carts is to incorporate an octane booster when you fill the tank. The cart will have more pick-up, and it could gain as much as 5 mph. A different approach is to take out the throttle linkage governor on the carburetor.
Do golf buggies have a carburetor?
Many older models have gas powered engines with a throttle and carburetor linkage. Aside from using the accelerator pedal to go slower or faster, there is a variety of options to adjust the speed of these great golf buggies.
How to remove coil from flywheel?
To remove the coil, the flywheel needs to be detached. Use a balance styled puller and attach the same to the threaded holes. Now add some pressure and let the puller do its job by removing the flywheel.
What is the purpose of a golf cart pulser coil?
The purpose of the Pulser coil is to give ignition signals to the engine and ignition system. The resistance categorizes pulser coils.
How to adjust a pulser coil?
The screws should be attached centrally. To adjust the coil stability, replaced the coil wire or the coil. Switch the coil wires to adjust the pulser.
Is the Ping G25 adjustable?
Is the Ping G25 driver adjustable? The Ping G25 driver is adjustable. It’s possible to do four adjustments using the hosel adapter of the driver apart from the stated loft setting and...
Why is my Ezgo golf cart belt so loose?
The reason your EZGO drive belt is too loose could be because it’s worn out, or you’re simply using the wrong size drive belt. In this case, need to find a replacement immediately. A loose drive belt can result in your EZGO Golf Cart to lose top speed and underperform.
Why is my EZGO drive belt so tight?
The reason your EZGO drive belt is too tight can be because you’re not using the right size drive belt. Check and make sure if you’re using the right one. A quick search online will give you the right information. It can also be too tight because the drive/driven clutch is misplaced or broken.
How to tell if golf cart drive belt is too tight?
To check if your drive belt is set just right make sure your golf cart is turned off then check the drive belt by pressing it down between the two clutches with your finger. If it deflects less than 1.5” it’s too tight.
Why is my clutch too tight?
It can also be too tight because the drive/driven clutch is misplaced or broken. A drive belt that’s too tight can damage the drive and driven clutches and can also result in the drive belt being worn out too fast. To check, whether the drive/driven clutch is misplaced or broken call a certified technician to have a look.
How to stop a EZYGO drive belt from slipping?
How to stop a EZYGO drive belt slipping: Make sure that you have the right drive belt. Sometimes the wrong drive belt will not be as wide as the clutch you are putting it on. This gives it an unwanted room to move back and forth when you are using the golf cart.
Can you tighten an EZGO drive belt?
You cannot tighten an EZGO drive belt. If loose, you will need to replace the drive belt. There have been various people online who’ve tried to store it in cold room temperatures hoping it would contract and become smaller but this is not recommended. Putting your drive belt at extreme temperatures can damage it.
Is the Ping G25 adjustable?
Is the Ping G25 driver adjustable? The Ping G25 driver is adjustable. It’s possible to do four adjustments using the hosel adapter of the driver apart from the stated loft setting and...
