Golf-FAQ.com

how to adjust timing on a columbia golf cart

by Beatrice Huels DVM Published 3 years ago Updated 2 years ago
image

Adjust TIMING to factory setting. With the points cover removed, you will see a scribe line on the points plate. Line this mark up with the punch mark on the side of the housing.

Full Answer

Why is timing important in a golf cart engine?

“Timing” is something that is very important to the proper operation of an engine. In this post we’ll take a look at the operation of 4-stroke engines in general, and then get a little more specific in our discussion, looking at a few models of golf carts and how they accomplish things. I always think […]

How do you adjust the idle on a golf cart?

Position the golf cart to idle mode and set the low idle air adjustment according to your preference, for the engine to be able to pick up properly. This adjustment can be found on top of the carburetor. Often, two turns outward from the seated position is a good starting option.

How do you adjust the carburetor on a Yamaha golf cart?

How to Adjust Yamaha Golf Cart Carburetor Yamaha G9 Carburetor Adjustment. Pull out the pilot adjustment screw. It must be present at a sharp point and not a flat spot. Rethread the screw back until it’s slightly seated. Turn the screw outwards by 1-1/2 turns. Push the throttle stop screw backward until the throttle shaft is closed completely.

How do you increase camber on a golf cart?

This simple trick will go a long way to maintain a proper camber. You can have a positive camber (which is actually not harmful for a golf cart) by getting a lift along with bigger tires. New king pins and bushings also help to get a bit of positive camber.

image

How to adjust carburetor on golf cart?

In most cases, you’ll need to adjust the jet pilot screw, perform a valve clearance adjustment and then clean the carburetor.

How to cool down a golf cart?

Procedure. Turn off the golf cart engine and allow it to cool for a couple of hours before you start working. This cooling down prevents damage to the cart and injury to yourself when you’re at work. Turn off the fuel-supply valve and remove the fuel line to prevent flooding of the fuel and other complications.

How to replace carburetor float?

Remove the carburetor and turn it upside down. Remove the nut that is used to secure the bowl on. Check the float for a puncture as this prevents the activation of the fuel cut-off needle valve. Replace the float if there is a puncture. Check for dirt accumulation in the needle valve.

Why does an EFI carb require more maintenance than an EFI?

The carb requires more maintenance than an EFI because of the cleaning and rebuilding of the carburetor involved.

Why does my carburetor flood on my golf cart?

The reason why a carburetor floods on a golf cart is usually due to a faulty fuel pump. The pump must be repaired or replaced accordingly. Seek professional assistance if required. This is usually due to the proximity of the fuel line to an exhaust manifold, a radiator hose or a heat source.

How to remove cable from carburetor?

Remove the cable from the carburetor and cover its sheath opening using duct tape. To do this, make a small funnel with the tape and ensure that the wire sticks out from its middle. Loosen the nut that fixes the cable on to the mount housed on the motor just before its entry into the carburetor.

Where is the main jet on a 2 cycle engine?

The main jet in the carburetor diagram of a 4-cycle engine is located below the carburetor while the pilot jet is present on top of it. The needle valve and float pin are also housed under the carburetor.

Why do golf carts need camber?

The camber is the angle of the wheels of a golf cart The camber is extremely important for maintaining the balance of the tyres on a golf cart. Golf cart owners need a good camber adjustment to ensure a smooth jerk-free ride. The golf cart’s wheels get wearied away over time due to regular rides over rough terrain, potholes and other uneven ground, ...

What size arm lift kit for Yamaha golf cart?

One can opt for a 6’ double A arm to avoid such a problem. A rollover or crashing golf cart: A six inch A arm lift kit that suits the Yamaha Drive model can cause reduced control over your golf cart if you don’t adjust the camber of its front wheels properly.

Why is my Yamaha G9 camber bad?

Worn out or incorrect struts are a key cause of camber problems in a Yamaha G9 golf cart. Often, this, combined with excessive positive camber can wear away your tires very easily. The positive camber can be a result of worn out shocks.

How to make a cart out of a car?

Begin by jacking up your car’s front wheels. Move out each of the wheels and make a pattern along the middle, covering the circumference. Now put them on the ground with the tires facing front. Drive the cart forward by approximately five feet with the tires in normal running position.

Why do my wheels have negative camber?

Consider replacing the struts and you will have a fine camber again. Negative camber can also be the result of wide tires or loose king pins. Don’t forget to check out the toe-in of your cart.

How to check camber on G1?

A good option to check the camber on a G1 is to check the toe-in. You can easily do that by watching it roll over a flat surface. If you detect an off toeing in, it will definitely reflect on the camber. You can put in a four stroke axle to take care of the problem. That should help.

How to jack up a car with a heim joint?

Use the parking brakes to jack up your car. Then loosen the lower heim joint by loosening the nut of the lower control arm. You must adjust the nuts to bring them closer to or farther from the frame of the car if the camber is out or in respectively. Lower the car and check the camber. Repeat the steps if needed.

golfcartman

What you have is a bad ignitor. It is a small part located behind the RPM limiter. Getting to it is a little tricky but I will try to explain. On the front of the motor, you will find 2 10mm bolts holding a black object that is the RPM limiter. Take these two bolts out and you will find the silver part behind the black box.

golfcartman

Is the motor turning? Only one fuse and the starter will not turn if it is bad. If the motor is not turning, make sure the belt is not slipping. If it is not slipping, make sure the engine will turn by hand. MAKE SURE KEY IS OFF BEFORE YOU PUT YOUR HANDS IN.

Where does the 2 vacuum hoses run to from the carburetor on a 1991 Gas Club Car Golf Cart?

It looks like they are not vacuum hoses, but overflows and vents. 1991 was when the model changed.

Everlasting turn signal flasher or relay location on a club car

Turn signals have never been a factory option on any standard carts. Only on models like the villager 8 passenger. Most likely behind the dash.

Golf cart starting

There is a custom Golf Cart that looks like a Jeep and is considered an electric club car. If you get a chance there is a show called Barter Kings and one of the shows actually shows one. They are not cheap.

Club car golf cart intermittent no spark

What you have is a bad ignitor. It is a small part located behind the RPM limiter. Getting to it is a little tricky but I will try to explain. On the front of the motor, you will find 2 10mm bolts holding a black object that is the RPM limiter. Take these two bolts out and you will find the silver part behind the black box.

The electric motor comes on but the engine does

Is the motor turning? Only one fuse and the starter will not turn if it is bad. If the motor is not turning, make sure the belt is not slipping. If it is not slipping, make sure the engine will turn by hand. MAKE SURE KEY IS OFF BEFORE YOU PUT YOUR HANDS IN.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9