1. Settingthe governor lever Adjust the length of the joint rod 1 so when the accelerator pedal isfully depressed, andthe governor lwer is turned counterclockwise, the carburetor thorttle valve just reaches the fully open position. (To adjust the joint rod length, loosen two locknuts, adjust the length, then tighten the locknuts.)
Full Answer
How do you adjust the carburetor on a Yamaha golf cart?
How to Adjust Yamaha Golf Cart Carburetor Yamaha G9 Carburetor Adjustment. Pull out the pilot adjustment screw. It must be present at a sharp point and not a flat spot. Rethread the screw back until it’s slightly seated. Turn the screw outwards by 1-1/2 turns. Push the throttle stop screw backward until the throttle shaft is closed completely.
Is there a service manual for the Yamaha G16 a golf cart?
This is the Highly Detailed factory service repair manual for theYAMAHA G16-A GOLF CART, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.
What kind of engine does a Yamaha golf cart have?
Initially, the Yamaha G1 2-cycle gas was the standard-bearer and in 1985 the G2 4-cycle single-cylinder gas engine was introduced as the new standard. link to How Does A Golf Cart Work? - Complete Guide To Understanding It (2021)
How do you adjust the idle on a golf cart?
Position the golf cart to idle mode and set the low idle air adjustment according to your preference, for the engine to be able to pick up properly. This adjustment can be found on top of the carburetor. Often, two turns outward from the seated position is a good starting option.
How do you adjust the valves on a Yamaha golf cart?
0:211:38How to Check your Golf Cart's Valve Adjustment | Golf Cars UnlimitedYouTubeStart of suggested clipEnd of suggested clipBetween your your rocker. And your valve. And you want to make sure there's no plane between thatMoreBetween your your rocker. And your valve. And you want to make sure there's no plane between that and that is your proper adjustment.
How do you adjust valves on a Yamaha?
4:5916:38How to Adjust Valve Clearance with Shims on Yamaha YZ250F - YouTubeYouTubeStart of suggested clipEnd of suggested clip15 millimeters right here so i go between the bucket. And between the lob of the cam. And i check.More15 millimeters right here so i go between the bucket. And between the lob of the cam. And i check. It goes and it goes the right way so i know i have 0 15 right now the other one on the intake.
How can I make my Yamaha gas golf cart go faster?
0:005:15Yamaha G29 Drive Golf Cart Governor Adjustment - MORE SPEED!!YouTubeStart of suggested clipEnd of suggested clipItself by tightening this nut down you're putting more pressure on the spring. So that the governorMoreItself by tightening this nut down you're putting more pressure on the spring. So that the governor has to work harder to pull back on the throttle.
How do I get more torque out of my Yamaha golf cart?
Change the Speed ControllerThe Speed Controller regulates the electric output of the motor; a higher voltage equals more RPM, and the faster your cart will travel. When you change the speed controller, you can reduce the voltage and increase the amperage of the motor, resulting in increased torque.
How do you adjust the valves on a Yamaha Raptor 700r?
7:4411:48Raptor 700 Valve Adjustment - YouTubeYouTubeStart of suggested clipEnd of suggested clipOr tolerance so tighten that up tighten or not.MoreOr tolerance so tighten that up tighten or not.
How do you adjust valve clearance with shims?
4:4812:40How to adjust shim over bucket valve clearances - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then subtract the difference which is the tenth hour that we need remove all those shims replaceMoreAnd then subtract the difference which is the tenth hour that we need remove all those shims replace them with the ones we need put the cam back in. And it should be should be pretty. Close.
Why is my gas golf cart running slow?
Low Battery Usually, the most common reason golf carts slow down is when they don't get enough power output from the battery. If the battery pack charge is very low and your cart is out of power, your cart will run slow.
How do you adjust the carburetor on a Yamaha golf cart?
How to Adjust Yamaha Golf Cart CarburetorPull out the pilot adjustment screw. ... Rethread the screw back until it's slightly seated.Turn the screw outwards by 1-1/2 turns.Push the throttle stop screw backward until the throttle shaft is closed completely.Turn the screw in by a 1/4 turn.
How do you take the governor off a Yamaha gas golf cart?
General InstructionsDetach the cable from the carburetor. The cable is about the width of a straw. ... Follow the disconnected cable up to the governor. ... Disconnect the gas pedal cable from the governor and reroute it to the carburetor. ... Using your wrench, remove the bolt on the gas pedal shaft.
How do I speed up my Yamaha electric golf cart?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
How do you remove the speed limiter on a electric golf cart?
0:000:46How to remove governor on a Club Car golf cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou open up this box lap. Here. It looks up look inside. There's 12 cable down right here this leverMoreYou open up this box lap. Here. It looks up look inside. There's 12 cable down right here this lever you want to lift up and Bend and that pulls on the cable a little more.
How do you put torque in a golf cart?
3:4917:29Plum Quick Rhino Torque Motor Install & Review - YouTubeYouTubeStart of suggested clipEnd of suggested clipParts of the stud. Of both sides. And you're going to need two to go on the top portion of the studsMoreParts of the stud. Of both sides. And you're going to need two to go on the top portion of the studs. For the mounting nut. Now what i've done here is i've taken some old wrenches.
What is a golf cart?
Golf carts are also known as golf cars. The term "cart", in its purest sense, refers to a vehicle that does not travel under its own power. Golf cars, however, are most commonly referred to as golf... link to Club Car DS Wiring Diagrams 1981 To 2002.
How many times can a Yamaha engine be rebuilt?
Yamaha engines are durable and because of the simple design, they can be successfully rebuilt 3 or 4 times . Initially, the Yamaha G1 2-cycle gas was the standard-bearer and in 1985 the G2 4-cycle single-cylinder gas engine was introduced as the new standard.
How to adjust carburetor on golf cart?
In most cases, you’ll need to adjust the jet pilot screw, perform a valve clearance adjustment and then clean the carburetor.
How to replace carburetor float?
Remove the carburetor and turn it upside down. Remove the nut that is used to secure the bowl on. Check the float for a puncture as this prevents the activation of the fuel cut-off needle valve. Replace the float if there is a puncture. Check for dirt accumulation in the needle valve.
Why does my carburetor flood on my golf cart?
The reason why a carburetor floods on a golf cart is usually due to a faulty fuel pump. The pump must be repaired or replaced accordingly. Seek professional assistance if required. This is usually due to the proximity of the fuel line to an exhaust manifold, a radiator hose or a heat source.
How to cool down a golf cart?
Procedure. Turn off the golf cart engine and allow it to cool for a couple of hours before you start working. This cooling down prevents damage to the cart and injury to yourself when you’re at work. Turn off the fuel-supply valve and remove the fuel line to prevent flooding of the fuel and other complications.
Where is the main jet on a 2 cycle engine?
The main jet in the carburetor diagram of a 4-cycle engine is located below the carburetor while the pilot jet is present on top of it. The needle valve and float pin are also housed under the carburetor.
Which is more powerful, carb or EFI?
The carb model is more powerful as well as starts and goes faster when compared to the EFI. The EFI experiences delay to start moving when the pedal is pressed.
How to remove cable from carburetor?
Remove the cable from the carburetor and cover its sheath opening using duct tape. To do this, make a small funnel with the tape and ensure that the wire sticks out from its middle. Loosen the nut that fixes the cable on to the mount housed on the motor just before its entry into the carburetor.