Adjust the needle valve with 1-1/2 turns in the outward direction. Adjust the valve on top of the throttle body with a 1/4 turn in the inward direction. Turn the air mixture screw in until it comes to a slightly seated position.
Full Answer
How to adjust a carburetor on a golf cart?
The way to adjust the carburetor on a golf cart will depend on the model of golf cart. In most cases, you’ll need to adjust the jet pilot screw, perform a valve clearance adjustment and then clean the carburetor. The engine shows a reduced performance such as a reduction in fuel efficiency or power and sluggish acceleration.
How to change drive belt on a club car golf cart?
How to Change the Drive Belt on a Club Car Golf Cart Switch the engine OFF after parking the golf cart.. Allow the engine to cool, if it has been running for some time.. Remove the engine cover.. You will be able to see the drive belt now.. Use an open-end wrench to loosen the drive belt tension ...
How do you adjust the governor on a club car G16?
Wrap a zip-tie around the governor arm bolt and pull it as tight as possible. This stimulates the same effect of tightening the locknut. The following methods show you how to adjust the governor on your Club Car G16 golf cart. Turn the 10mm nut inward until you get the desired speed.
How to adjust the carburetor on a 1995 gas club car?
1995 Gas Club Car Carburetor Adjustment 1 Start the adjustment with the mixture screw in a slightly seated position. Turn it outside by 1-1/2 turns. 2 Continue adjusting outward or inward in small increments. 3 Check the air filter housing and the intake hose to ensure that they don’t have any air leak. 4 Replace the fuel filter if needed.
How do you adjust the valves on a golf cart?
0:431:38How to Check your Golf Cart's Valve Adjustment | Golf Cars UnlimitedYouTubeStart of suggested clipEnd of suggested clipYou do need to adjust them you can just there's adjusters right here on top of the rockers. You'llMoreYou do need to adjust them you can just there's adjusters right here on top of the rockers. You'll loosen them and adjust accordingly.
Why does my club car backfire?
The golf cart backfires through the carburetor because of an open throttle plate. The accelerator cable at the scale is out of adjustment and, in turn, stops the vessel from closing when the microswitch makes contact with the ignition.
How do you adjust the carburetor on a Club Car golf cart?
Find the pilot adjustment screw on the edge of your carburetor. Pay attention to this screw – it should be a sharp point and not flat. Carefully remove this screw and then carefully screw it back. Turn this screw out one and one-half turns to adjust it properly.
Can you adjust the speed on a Club Car golf cart?
0:131:31Club Car Precedent Speed Increase SUPER EASY!!! - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you turn it that way to the right or what appears to be counterclockwise. It slows it down. AndMoreIf you turn it that way to the right or what appears to be counterclockwise. It slows it down. And if you turn it that way or clockwise it speeds things up. Very.
Why does my golf cart backfire when I let off the gas?
The golf cart backfires when you let off gas is because the carburetor butterfly isn't getting closed completely. Air suction from the exhaust gasket is another possible cause. Checking the carburetor and adjusting the return spring to its original position so that the carburetor is closed solves the problem.
What causes a golf cart to sputter?
Golf carts can spit and sputter for several reasons, but mainly due to worn out spark plugs or dirty filters inside the fuel system. There might be something wrong with the fuel system of your cart. You could be having a spit and sputter problem because the filter, pump and injectors in your golf cart are very dirty.
Why does my golf cart only run with the choke on?
Dwight Coleman there are usually only a few possibilities if it only runs with the choke. One cause could be an air leak on the carb, head gasket, crankshaft seal. The other could be a clogged low speed and idle circuit.
How do you clean the carburetor on a Club Car golf cart?
2:1217:47How to Take Apart and Clean a Carburetor - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf there's some little crevices with gunk in it and so what I do after I take time to clean it is IMoreIf there's some little crevices with gunk in it and so what I do after I take time to clean it is I use some brake cleaner.
How do you adjust the throttle on a gas golf cart?
Pull the spring that is present around the plastic piece located behind the shifter. Spin it until it falls back. Loosen the throttle cable present in the cable box to adjust the extent to which you can take it out of the housing. Press the accelerator so that the golf cart starts up and begins to idle.
How do you make a Club Car golf cart go faster?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
Why is my Club Car so slow?
The main reasons for a Club Car Precedent running slow is because of a weak battery, or faults with the MCOR, solenoid and throttle cable. Some of the other reasons the cart may slow down are: Solenoid contacts can get jammed as they wear out; experts call this 'welded solenoid'. The MCOR could be an issue.
Why does my golf cart go slow up hills?
While battery problems tend to be the most common reason for slow speeds uphill. The size of your tires, speed, wire corrosion, and brake solenoid damage are also possible causes for your cart's slow speeds. I recommend checking your batteries before anything else.
How to adjust carburetor on golf cart?
In most cases, you’ll need to adjust the jet pilot screw, perform a valve clearance adjustment and then clean the carburetor.
How to cool down a golf cart?
Procedure. Turn off the golf cart engine and allow it to cool for a couple of hours before you start working. This cooling down prevents damage to the cart and injury to yourself when you’re at work. Turn off the fuel-supply valve and remove the fuel line to prevent flooding of the fuel and other complications.
How to replace carburetor float?
Remove the carburetor and turn it upside down. Remove the nut that is used to secure the bowl on. Check the float for a puncture as this prevents the activation of the fuel cut-off needle valve. Replace the float if there is a puncture. Check for dirt accumulation in the needle valve.
Why does an EFI carb require more maintenance than an EFI?
The carb requires more maintenance than an EFI because of the cleaning and rebuilding of the carburetor involved.
Why does my carburetor flood on my golf cart?
The reason why a carburetor floods on a golf cart is usually due to a faulty fuel pump. The pump must be repaired or replaced accordingly. Seek professional assistance if required. This is usually due to the proximity of the fuel line to an exhaust manifold, a radiator hose or a heat source.
How to remove cable from carburetor?
Remove the cable from the carburetor and cover its sheath opening using duct tape. To do this, make a small funnel with the tape and ensure that the wire sticks out from its middle. Loosen the nut that fixes the cable on to the mount housed on the motor just before its entry into the carburetor.
Where is the main jet on a 2 cycle engine?
The main jet in the carburetor diagram of a 4-cycle engine is located below the carburetor while the pilot jet is present on top of it. The needle valve and float pin are also housed under the carburetor.
How to remove golf cart clutch?
For removing the old one, follow these steps: Switch OFF the golf cart’s engine. Take a screwdriver and gently insert it between the belt’s bottom and the clutch’s groove. Slowly rotate the clutch and the belt will come off easily. If the belt is already loose, taking it out is very easy.
How to check if golf cart drive belt is too tight?
To check if the drive belt is too tight, follow these steps: Switch OFF the golf cart ’s engine. Reach to where the drive belt is located and use your fingers to press the drive belt between the two clutches. The belt must deflect at least one and a half inches under the pressure of your fingers.
How to tell if a 1997 club car has a slipping drive belt?
When a 1997 Club Car drive belt is slipping, first make sure that it is the drive belt that is at fault. You may have to remove the cover and watch the clutches in action while the cart is in motion to make sure that it is indeed the drive belt that is slipping.
How to remove drive belt?
Removing the drive belt involves holding the belt with both hands in the center between the driven and drive clutches and lifting the belt. You must now rotate the driven clutch counter-clockwise and slip the belt off the sheave. You can then slide the drive belt off the drive clutch.
Why is my club car drive belt so tight?
The reason for a Club Car drive belt being too tight can be because the drive belt is too small for the golf cart. The way to check if the belt is fitted correctly is to push the belt down with one finger at the center between the clutches. It should not deflect more than 1.5inches. It should not be less as well.
What is the primary function of a golf cart drive belt?
To primary function of a golf cart drive belt is to connect the primary clutch and the secondary clutch. The primary clutch drives the cart and the belt helps it to rotate the secondary clutch (they are referred to as the drive clutch and the driven clutch respectively). The drive belt, unlike some of the other automotive belts, are very thick.
Why does my golf cart drive belt slip?
The reason for the drive belt slipping could be that it is of a larger/longer size and therefore loose. You may start feeling the slippage after driving for a while. This is because the belt gets heated up after the golf cart runs for some time and loosens further .
How to change the speed of a golf cart?
Locate the spring on the differential or carburetor that helps in changing the cart speed by adjusting its tension. Increase the length of the cable that is fitted on to the body of the throttle and clutch of the two-stroke engine.
How to start a golf cart with a gas pedal?
Locate the gas pedal that is fitted to the governor and remove the connection. Re-route the gas pedal to the carburetor. Remove the bolt present on the shaft of the gas pedal. Slide the shaft upwards so that the gas pedal has more play. Tighten the bolt and start the golf cart.
How fast is an EZGO golf cart?
The top speed of an EZGO golf cart is usually 19.9mph and the average speed is 14mph to 15mph. With governor adjustment, the EZGO cart can go faster by 5 to 10mph.
What is a golf cart governor?
A golf cart governor is a mechanical device that helps in controlling the maximum speed of the cart when it moves on flat ground. This device prevents the engine RPMs from increasing beyond the recommended specifications.
How to ride a golf cart at full speed?
Ride the cart at full speed over a course of known length. This will ensure that the governor controls the speed of the cart within factory specifications. Fasten the black plastic cover and put the seat back in place. Take care when tightening the nut. The more you tighten, the faster your cart will go.
Where is the governor arm on a golf cart?
Locate the governor arm of the golf cart. This is mounted above the rear axle housing and under the cart. Depending on the cart model, there may be a protection plate above the governor.
Can you remove a golf cart governor?
It doesn’t take much time or skill to remove a golf cart governor. With some basic mechanical expertise and general-purpose tools, you can do this yourself. The process is more or less the same in all golf carts.
