Pick a valve. Turn cam lobe DOWN by rotating drive clutch by hand (red arrow): Loosen adjuster locknut 1/4-1/2 turn. Insert.004" feeler gauge between cam, and lifter (red arrow): Turn adjuster until feeler gauge has very slight drag, but is free.
Full Answer
How do you adjust the speed on an EZ GO golf cart?
Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.
How to adjust a carburetor on a golf cart?
The way to adjust the carburetor on a golf cart will depend on the model of golf cart. In most cases, you’ll need to adjust the jet pilot screw, perform a valve clearance adjustment and then clean the carburetor. The engine shows a reduced performance such as a reduction in fuel efficiency or power and sluggish acceleration.
How do I install a throttle scale on my 2002 EZ GO?
How do I install a throttle scale on my 2002 E Z Go golf cart? Depending on whether it has a power source to itself, if it has a personal power source, then just add duct tape or anything that will make it stay onto the 2002 EZ Go Golf Cart. And if the throttle scale doesn't, then just search it up.
How do I tune-up my E-Z-Go gasoline engine?
These are the easy steps to perform a basic tune-up on your E-Z-Go gasoline engine using a minimum of tools and an optional tune-up kit. As always, we begin with the three basics…Air, fuel, spark. Unsure of your year and model?
How do you adjust the valves on a golf cart?
0:431:38How to Check your Golf Cart's Valve Adjustment | Golf Cars UnlimitedYouTubeStart of suggested clipEnd of suggested clipYou do need to adjust them you can just there's adjusters right here on top of the rockers. You'llMoreYou do need to adjust them you can just there's adjusters right here on top of the rockers. You'll loosen them and adjust accordingly.
How do you adjust the carburetor on a EZ Go golf cart?
2 Cycle engine: The adjustment screw is on the side of the carburetor and is parallel to the ground. You can identify it by the lock nut at the base of the screw. Loosen this and turn the screw all the way into a soft seat, then back it out one and a half (1-1/2) turns.
How do I adjust the speed on my EZ Go golf cart?
0:237:10Simple Adjusting of an E Z Go Golf Cart Governor - YouTubeYouTubeStart of suggested clipEnd of suggested clipEngine. One Titan the governor spring located in the engine of most golf carts to adjust your cartsMoreEngine. One Titan the governor spring located in the engine of most golf carts to adjust your carts top speed.
How do you adjust the governor on a EZGO TXT gas golf cart?
1:065:06How to Adjust an E Z Go Golf Cart Governor - WikiVideo - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you are curious this is your carts carburetor loosen the small nut and tighten the larger nut.MoreIf you are curious this is your carts carburetor loosen the small nut and tighten the larger nut. The more you tighten the larger nut the faster your cart will.
What causes an ezgo golf cart to backfire?
The golf cart backfires through the carburetor because of an open throttle plate. The accelerator cable at the scale is out of adjustment and, in turn, stops the vessel from closing when the microswitch makes contact with the ignition.
What causes a gas golf cart to sputter?
Golf carts can spit and sputter for several reasons, but mainly due to worn out spark plugs or dirty filters inside the fuel system. There might be something wrong with the fuel system of your cart. You could be having a spit and sputter problem because the filter, pump and injectors in your golf cart are very dirty.
How do you speed up a 36 volt EZ Go golf cart?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
How do I increase the speed of my ezgo TXT gas?
Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.
Why is my gas golf cart running slow?
Low Battery Usually, the most common reason golf carts slow down is when they don't get enough power output from the battery. If the battery pack charge is very low and your cart is out of power, your cart will run slow.
What does removing the governor do?
Removing the governor will increase the maximum rpm of the engine, but the internal parts of the Predator 212 are designed for 3600 rpm. Generally, this isn't an issue with just the governor removal, the internal parts can usually withstand 5000 rpm without breaking apart (unless you go full throttle for too long).
How fast can a golf cart go without a governor?
A typical electric cart without an upgraded speed control tops out around 12 mph.
How do you take the governor off a EZ Go golf cart?
General InstructionsDetach the cable from the carburetor. The cable is about the width of a straw. ... Follow the disconnected cable up to the governor. ... Disconnect the gas pedal cable from the governor and reroute it to the carburetor. ... Using your wrench, remove the bolt on the gas pedal shaft.
For the 295cc or a 350cc twin-cylinder OHC engine. 1991 – Present
Tools required: Ratchet with 6″ extension, 10mm socket, 10mm socket wrench, flat blade screwdriver, and a feeler gauge. Note: if the screw (C) has a square head instead of a flat blade slot, this takes a tool designed just for this purpose.
For the Kawasaki FJ400 401cc 4-cycle Single Cylinder 1996 – Present
Tools required: Ratchet with 6″ extension, 10mm socket, 3mm hex wrench, feeler gauge.
How to adjust EZ Go cart governor?
To adjust an EZ Go Cart Governor engine, start by removing the seat so that you can access the engine. Once the seat is off, remove the screws from the black plastic cover at the rear of the seat and then set the cover aside.
How to raise the top speed of a golf cart?
To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly. If you cannot find this spring, you likely have a newer model that is more difficult to adjust, though this is rare. Lift up the seat. Remove the seat cousins, which hide the engine.
How to make a golf cart go faster?
Loosen the small nut and tighten the larger nut. The more you tighten the larger nut, the faster your cart will go. Start slowly, only tightening the nut a quarter turn to start. You can over-stress the engine if you try to run it too quickly, and it will skip and potentially burn out if you are too eager.
How to get a cart to move faster?
1. Remove the seat and plastic covering over the engine. Sometimes you'll need to remove screws while some models have seats that pop right out. Expose the engine so that you can get to work adjusting the motor. If you don't have a central governor spring, you can still get your cart to move a little faster.
How fast can a golf cart go?
Adjusting the governor can make your golf cart go 5–10 mph (8 .0–16.1 km/h) faster. If you do this to an E-Z-GO golf cart, you might be able to go from 15 mph (24 km/h) to 22 mph (35 km/h). It will only take about 5 minutes to do it. Steps.
How many screws are in a golf cart engine?
There should be five screws in most models. The engine is in the front of golf carts, underneath this panel. Take off the plastic cover and set it aside with the seats. ...
How to change the speed of a car?
Locate your clutch pedal and line. The clutch is the pedal (sometimes a handle near your knee) that you use to put the car into reverse or change speeds. You can adjust the clutch to send more gas to your engine, moving you faster. ...
How to adjust carburetor on golf cart?
In most cases, you’ll need to adjust the jet pilot screw, perform a valve clearance adjustment and then clean the carburetor.
How to cool down a golf cart?
Procedure. Turn off the golf cart engine and allow it to cool for a couple of hours before you start working. This cooling down prevents damage to the cart and injury to yourself when you’re at work. Turn off the fuel-supply valve and remove the fuel line to prevent flooding of the fuel and other complications.
How to replace carburetor float?
Remove the carburetor and turn it upside down. Remove the nut that is used to secure the bowl on. Check the float for a puncture as this prevents the activation of the fuel cut-off needle valve. Replace the float if there is a puncture. Check for dirt accumulation in the needle valve.
Why does my carburetor flood on my golf cart?
The reason why a carburetor floods on a golf cart is usually due to a faulty fuel pump. The pump must be repaired or replaced accordingly. Seek professional assistance if required. This is usually due to the proximity of the fuel line to an exhaust manifold, a radiator hose or a heat source.
Where is the main jet on a 2 cycle engine?
The main jet in the carburetor diagram of a 4-cycle engine is located below the carburetor while the pilot jet is present on top of it. The needle valve and float pin are also housed under the carburetor.
How to remove cable from carburetor?
Remove the cable from the carburetor and cover its sheath opening using duct tape. To do this, make a small funnel with the tape and ensure that the wire sticks out from its middle. Loosen the nut that fixes the cable on to the mount housed on the motor just before its entry into the carburetor.
Why does an EFI carb require more maintenance than an EFI?
The carb requires more maintenance than an EFI because of the cleaning and rebuilding of the carburetor involved.
Why is my Ezgo golf cart belt so loose?
The reason your EZGO drive belt is too loose could be because it’s worn out, or you’re simply using the wrong size drive belt. In this case, need to find a replacement immediately. A loose drive belt can result in your EZGO Golf Cart to lose top speed and underperform.
Why is my EZGO drive belt so tight?
The reason your EZGO drive belt is too tight can be because you’re not using the right size drive belt. Check and make sure if you’re using the right one. A quick search online will give you the right information. It can also be too tight because the drive/driven clutch is misplaced or broken.
How to tell if golf cart drive belt is too tight?
To check if your drive belt is set just right make sure your golf cart is turned off then check the drive belt by pressing it down between the two clutches with your finger. If it deflects less than 1.5” it’s too tight.
How to stop a EZYGO drive belt from slipping?
How to stop a EZYGO drive belt slipping: Make sure that you have the right drive belt. Sometimes the wrong drive belt will not be as wide as the clutch you are putting it on. This gives it an unwanted room to move back and forth when you are using the golf cart.
Can you tighten an EZGO drive belt?
You cannot tighten an EZGO drive belt. If loose, you will need to replace the drive belt. There have been various people online who’ve tried to store it in cold room temperatures hoping it would contract and become smaller but this is not recommended. Putting your drive belt at extreme temperatures can damage it.
Is the Ping G25 adjustable?
Is the Ping G25 driver adjustable? The Ping G25 driver is adjustable. It’s possible to do four adjustments using the hosel adapter of the driver apart from the stated loft setting and...
Can you adjust a drive belt on an EZGO golf cart?
There is no way to adjust a drive belt, so it’s important to get the right size belt in the first place. To be sure, visit your local mechanic or call a certified technician to help you get the right drive belt for your EZGO golf cart.
What is a golf cart?
Golf carts are also known as golf cars. The term "cart", in its purest sense, refers to a vehicle that does not travel under its own power. Golf cars, however, are most commonly referred to as golf... link to Club Car DS Wiring Diagrams 1981 To 2002.
Where is the second filter on a carburetor?
Return the filter to the gas line and secure it with the clamps. Sometimes there is a second filter located underneath the carburetor facing the front of the cart. Check to see if you have one and make sure it is also clear of deposits.
How to Adjust a Golf Cart Carburetor
The way to adjust the carburetor on a golf cart will depend on the model of golf cart. In most cases, you’ll need to adjust the jet pilot screw, perform a valve clearance adjustment and then clean the carburetor.
Bad Golf Cart Carburetor Symptoms
The engine shows a reduced performance such as a reduction in fuel efficiency or power and sluggish acceleration.
Troubleshooting Golf Cart Carburetor Problems
Adjust the idle jet pilot screw on the carburetor. This can be done by doing a 1/4 turn of the screw.
How to Adjust Yamaha Golf Cart Carburetor
Pull out the pilot adjustment screw. It must be present at a sharp point and not a flat spot.
Yamaha Golf Cart Carb Vs EFI
The carb model is more powerful as well as starts and goes faster when compared to the EFI. The EFI experiences delay to start moving when the pedal is pressed.
How to Adjust EZGO Golf Cart Carburetor
Check the valve adjustment for proper compression using a compression tester. You will have to pull out the plugs and put the tester inside.
EZGO Golf Cart Carburetor Diagram
The EZGO TXT gas golf cart carburetor diagram shows just one adjustment on the engine. This is present above the carburetor towards its rear. In a 2-cycle cart, this is the idle circuit and is initially set for 1-1/2 outward turns.
