Position the golf cart to idle mode and set the low idle air adjustment according to your preference, for the engine to be able to pick up properly. This adjustment can be found on top of the carburetor. Often, two turns outward from the seated position is a good starting option.
Full Answer
How do I adjust the top speed of my golf cart?
It will only take about 5 minutes to do it. Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.
How do you adjust the carburetor on a Yamaha golf cart?
How to Adjust Yamaha Golf Cart Carburetor Yamaha G9 Carburetor Adjustment. Pull out the pilot adjustment screw. It must be present at a sharp point and not a flat spot. Rethread the screw back until it’s slightly seated. Turn the screw outwards by 1-1/2 turns. Push the throttle stop screw backward until the throttle shaft is closed completely.
How do you adjust the governor on a golf cart?
Simply adjust the cable coming from this metal protrusion, turning the nut counterclockwise to make the cable longer, effectively adjusting the cart’s governance to increase the overall speed. If you cannot find external controls, you’ll need to adjust the governor internally.
How do you jack up a golf cart?
Put the brick or blocks in front and behind each of the front wheel of the golf cart to prevent it from rolling. Get the floor jack into position at the rear of the golf cart. The two rear wheels should be lifted simultaneously off the ground.
How do you adjust the toe on a golf cart?
Loosen the tie rod on the driver's side wheel and adjust the toe in by twisting the rod left or right depending on the direction you need to adjust the tire. If you need to adjust the tire inwards (towards the front of the cart) then turn the rod towards the rear of the cart, which will turn the tire in.
How do you adjust the camber on a EZ Go golf cart?
Unfortunately, there is no camber adjustment permitted on a normal EZGO TXT golf cart. However, feel free to go in for toe adjustment if required. Sometimes, adjusting the end of the tie rods does the trick for this model.
How do I adjust my EZ GO carburetor?
2 Cycle engine: The adjustment screw is on the side of the carburetor and is parallel to the ground. You can identify it by the lock nut at the base of the screw. Loosen this and turn the screw all the way into a soft seat, then back it out one and a half (1-1/2) turns.
How do you adjust the toe on a Club Car DS?
2:183:45How to Adjust the Toe In on a Club Car Precedent Golf Cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd actually turn the tie rod. Itself one of the pasture side you go up. And it brings to toe in onMoreAnd actually turn the tie rod. Itself one of the pasture side you go up. And it brings to toe in on this tire inward. Where on the driver side would be exactly opposite this one would go back.
How do you align the front end of a EZ Go golf cart?
3:003:54EZGO RXV Toe-In Check - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell as that we had another successful day here at the garage checking toe it on our rhv. Don'tMoreWell as that we had another successful day here at the garage checking toe it on our rhv. Don't forget to Like and subscribe and also for our your parks accessories DIY golf cart calm.
How do you fix negative camber?
1:327:05HOW TO FIX YOUR CAMBER!! - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what happens is you put the spacer in right there put the spacer in and it pushes da arm downMoreSo what happens is you put the spacer in right there put the spacer in and it pushes da arm down which flips up the vehicle looks up all this.
How do you adjust the carburetor on a golf cart?
Find the pilot adjustment screw on the edge of your carburetor. Pay attention to this screw – it should be a sharp point and not flat. Carefully remove this screw and then carefully screw it back. Turn this screw out one and one-half turns to adjust it properly.
Why does my golf cart only run with the choke on?
Dwight Coleman there are usually only a few possibilities if it only runs with the choke. One cause could be an air leak on the carb, head gasket, crankshaft seal. The other could be a clogged low speed and idle circuit.
What causes golf cart hesitation?
In most cases, the hesitation problem occurs due to bad batteries. If you have bought new batteries for your EZGO RXV, make sure to fully charge them before the first use. Batteries should then be charged after every use. To keep the batteries in check, get a Digital MultiMeter to measure the individual voltage.
How do you adjust the steering on a Club Car golf cart?
Turn the steering wheel to either side and lock it. Do this a few times and watch out for any play or slippage. Turn the wheel once again to any side slightly so that the rack moves out of the neutral position. Loosen the adjustment nut at the bottom of the cart with counter-clockwise turns using a large wrench.
How do you adjust the tie rods on a Club Car DS?
6:429:35Club Car DS Front End Alignment - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo i'm going to loosen my screws to the max. On each side to stay right there i'll do the same onMoreSo i'm going to loosen my screws to the max. On each side to stay right there i'll do the same on this side. And then i'll begin to tighten this down. And it's just a hand tight.
How do you adjust the steering on a EZ Go golf cart?
Rotate the middle adjustment clockwise to attach with the rack. Again, turn counter-clockwise by a 22.5 to 45-degree angle. Repeat this step to assess the binding. If the steering wheel is not binding well, then the issue could be with tie rods and may need replacement.
How to change the speed of a golf cart?
Locate the spring on the differential or carburetor that helps in changing the cart speed by adjusting its tension. Increase the length of the cable that is fitted on to the body of the throttle and clutch of the two-stroke engine.
How to ride a golf cart at full speed?
Ride the cart at full speed over a course of known length. This will ensure that the governor controls the speed of the cart within factory specifications. Fasten the black plastic cover and put the seat back in place. Take care when tightening the nut. The more you tighten, the faster your cart will go.
How to start a golf cart with a gas pedal?
Locate the gas pedal that is fitted to the governor and remove the connection. Re-route the gas pedal to the carburetor. Remove the bolt present on the shaft of the gas pedal. Slide the shaft upwards so that the gas pedal has more play. Tighten the bolt and start the golf cart.
How fast is an EZGO golf cart?
The top speed of an EZGO golf cart is usually 19.9mph and the average speed is 14mph to 15mph. With governor adjustment, the EZGO cart can go faster by 5 to 10mph.
What is a golf cart governor?
A golf cart governor is a mechanical device that helps in controlling the maximum speed of the cart when it moves on flat ground. This device prevents the engine RPMs from increasing beyond the recommended specifications.
Where is the governor arm on a golf cart?
Locate the governor arm of the golf cart. This is mounted above the rear axle housing and under the cart. Depending on the cart model, there may be a protection plate above the governor.
Can you remove a golf cart governor?
It doesn’t take much time or skill to remove a golf cart governor. With some basic mechanical expertise and general-purpose tools, you can do this yourself. The process is more or less the same in all golf carts.
How to find the governor on a golf cart?
Locate the golf cart’s governor; you can find the governor by tracing the thickest cable running from the gas pedal. This cable runs through the governor on its way to the carburetor. Use a screwdriver—or in some cases a wrench—to loosen the tension on the governor’s springs. You have now adjusted the governor for faster speed.
Who is the writer of GolfCarCatalog.com?
GolfCarCatalog.com – “Adjusting Your Golf Cart’s Governor”. Writer Bio. Richard Kalinowski began writing professionally in 2006. He also works as a website programmer and graphic designer for several clients.
Can a golf cart be a nuisance?
In practice, golf carts can be more of a nuisance than a help, as many standard carts creep along at unbearably slow speeds. Luckily, you don’t have to stick with these standard speeds. Golf cart speed is often controlled by a device called a governor, and you can adjust the governor on a golf cart relatively easily to make the cart faster.
Can golf carts be adjusted manually?
By Richard Kalinowski. Governors limit the speed of golf carts but can be adjusted manually. In theory, golf carts make it easier for players to get across the course, saving their much-needed energy for the game. In practice, golf carts can be more of a nuisance than a help, as many standard carts creep along at unbearably slow speeds.
How to make a golf cart go faster?
Loosen the small nut and tighten the larger nut. The more you tighten the larger nut, the faster your cart will go. Start slowly, only tightening the nut a quarter turn to start. You can over-stress the engine if you try to run it too quickly, and it will skip and potentially burn out if you are too eager.
How to raise the top speed of a golf cart?
To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly. If you cannot find this spring, you likely have a newer model that is more difficult to adjust, though this is rare. Lift up the seat. Remove the seat cousins, which hide the engine.
How to adjust EZ Go cart governor?
To adjust an EZ Go Cart Governor engine, start by removing the seat so that you can access the engine. Once the seat is off, remove the screws from the black plastic cover at the rear of the seat and then set the cover aside.
How to get a cart to move faster?
1. Remove the seat and plastic covering over the engine. Sometimes you'll need to remove screws while some models have seats that pop right out. Expose the engine so that you can get to work adjusting the motor. If you don't have a central governor spring, you can still get your cart to move a little faster.
How fast can a golf cart go?
Adjusting the governor can make your golf cart go 5–10 mph (8 .0–16.1 km/h) faster. If you do this to an E-Z-GO golf cart, you might be able to go from 15 mph (24 km/h) to 22 mph (35 km/h). It will only take about 5 minutes to do it. Steps.
How many screws are in a golf cart engine?
There should be five screws in most models. The engine is in the front of golf carts, underneath this panel. Take off the plastic cover and set it aside with the seats. ...
How to change the speed of a car?
Locate your clutch pedal and line. The clutch is the pedal (sometimes a handle near your knee) that you use to put the car into reverse or change speeds. You can adjust the clutch to send more gas to your engine, moving you faster. ...
Why is it important to adjust the distance of travel on a golf cart?
It is important to adjust this distance of travel to make sure that the brakes are working properly. If there is too much travel distance, the braking capacity or power of the golf cart will be reduced. But if the distance is too short, the brakes may not release fully. So adjustments are necessary in both cases.
How to adjust brakes on a golf cart?
Here are the steps in adjusting the brakes: Turn off the power of the golf cart. Don’t set its parking brake. Put the brick or blocks in front and behind each of the front wheel of the golf cart to prevent it from rolling. Get the floor jack into position at the rear of the golf cart.
How to remove lug nuts on a car?
Use the socket wrench to loosen the lug nuts on the rear wheels. Remove the nuts and the wheels and set them aside. Remove the rubber boots on the underside of the wheels and the brake adjustment screw will be exposed. Pull these rubber boots away from the wheels by using your hands.
Do golf carts have brakes?
As in ordinary vehicles, golf carts have brakes. If you notice that the brakes are not functioning well, they need to be adjusted. Here are some of the ways by which you can adjust the brakes of different types of golf carts. This is also part of the golf cart maintenance checklist that we’ve created. Contents [ show]
Is it safe to drive a golf cart?
Just like any vehicle, safety is very important in driving a golf cart. If not properly handled a golf cart could also cause accidents, although not as serious as the accidents caused by bigger cars and trucks. Nevertheless, you should also know how to safely drive and operate a golf cart. As in ordinary vehicles, golf carts have brakes.
Do old golf carts have low switches?
Some of the old style golf carts may have run/low switches. These switches should be shifted to the tow position before disconnecting their battery packs. Lift the back of the golf cart and put the floor jack in a secure section of the cart which should provide it a stable support.
How to make a golf cart go forward?
If yours is the rocker switch that you use to make the golf cart go forward or reverse than place it in the middle position. Or if yours is the bulky knob down in front of the bottom seat then place it in the straight up or neutral position. Thirdly, lift the seat and place the tow/run switch in the “tow” position.
How fast can a golf cart go?
This is the reason that most golf cart manufacturers suggest not to exceed speeds of five to eight miles per hour while towing the golf cart. Higher speeds produce higher motor rpms which lead to devastating heat!
Where is the shifter knob on a golf cart?
This is an absolute must if your golf cart is a series cart. These are the carts that have a bulky shifter knob located down in front of the bottom seat. Secondly, place the shifter on the FNR switch in the neutral position. If yours is the rocker switch that you use to make the golf cart go forward or reverse than place it in the middle position.
What happens when the armature rpm is high?
This extreme heat melts the brush holder and them burns the field coils and ultimately explodes the windings of the armature which in turn wipes out the motor and eventually locks up.
Where is the tow switch on a golf cart?
On the older Club cars, the tow/run switch is located at the top of the battery compartment toward the front under the seat and also at the top in the middle of the four twelve volt batteries.
Do you need a wrench for a golf cart?
I realize most people do not carry wrenches with them when using a golf cart, however even if you can use a pair of pocket pliers it is advisable to unhook the electrical connection of the batteries to the golf cart. This is an absolute must if your golf cart is a series cart.
Do golf carts break down?
Unfortunately, there are times that they decide it’s quitting time and that they need a break. These times seldom ever happen at a convenient time. You know, like in your garage or at the cart barn. The golf cart will usually break down during usage whether out on the back nine or while your kids have it down at the community center swimming in ...
How to Adjust a Golf Cart Carburetor
The way to adjust the carburetor on a golf cart will depend on the model of golf cart. In most cases, you’ll need to adjust the jet pilot screw, perform a valve clearance adjustment and then clean the carburetor.
Bad Golf Cart Carburetor Symptoms
The engine shows a reduced performance such as a reduction in fuel efficiency or power and sluggish acceleration.
Troubleshooting Golf Cart Carburetor Problems
Adjust the idle jet pilot screw on the carburetor. This can be done by doing a 1/4 turn of the screw.
How to Adjust Yamaha Golf Cart Carburetor
Pull out the pilot adjustment screw. It must be present at a sharp point and not a flat spot.
Yamaha Golf Cart Carb Vs EFI
The carb model is more powerful as well as starts and goes faster when compared to the EFI. The EFI experiences delay to start moving when the pedal is pressed.
How to Adjust EZGO Golf Cart Carburetor
Check the valve adjustment for proper compression using a compression tester. You will have to pull out the plugs and put the tester inside.
EZGO Golf Cart Carburetor Diagram
The EZGO TXT gas golf cart carburetor diagram shows just one adjustment on the engine. This is present above the carburetor towards its rear. In a 2-cycle cart, this is the idle circuit and is initially set for 1-1/2 outward turns.
