Yamaha G9 throttle cable adjustment Slide the cable through the little slit present on the side of the cart. Position the cable so that the wire part is in the spool.
Full Answer
How do I adjust the throttle cable on my electric golf cart?
Ensure that the throttle plate is closed fully and the governor arm is rotated in the counter-clockwise direction completely. Loosen the nut that is near the throttle cable bracket and positioned towards the back of the cart.
Why is the accelerator cable slack on a golf cart?
The slack at the pedal on the first accelerator cable prevents breaking at the lead end while the slack on the second accelerator cable ensures that the cart engine turns over and the throttle shaft opens only after the ignition fires. However, the cable must have the required tightness to render full throttle.
How do you start a golf cart with a loose cable?
Press the accelerator so that the golf cart starts up and begins to idle. Check the cable tension to make sure that it’s still loose. The idle screw can be used to adjust the idling if it’s very fast. Turn the key to the OFF position and put the cable back into the box.
How to adjust the throttle cable on a Honda Accord?
Method 2 1 Fit a heavy spring to the throttle cable at its end. 2 Adjust the throttle cable at the differential to the endpoint of the threads. 3 Bend the throttle cable bracket outwards by about 0.25 inches so that there is a slightly heavy pull on the governor and a short throw on the pedal at the ...
How do you replace an accelerator cable?
1:2611:33How To Replace a 2 Stroke Throttle Cable - YouTubeYouTubeStart of suggested clipEnd of suggested clipSlide that the throttle cable is attached to now to do that we need to gain access to these twoMoreSlide that the throttle cable is attached to now to do that we need to gain access to these two screws that are on the top of the carburetor now to do that we need to loosen. These clamps right here.
How do you remove an accelerator pedal cable?
2:046:44Accelerator Cable Removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust pull out on it. Just snaps right out of the pedal. And then there's a little groove in the armMoreJust pull out on it. Just snaps right out of the pedal. And then there's a little groove in the arm for the cable. And then there it is cable is all free of the pedal.
How do you adjust the throttle cable on a Yamaha golf cart?
0:005:15Yamaha G29 Drive Golf Cart Governor Adjustment - MORE SPEED!!YouTubeStart of suggested clipEnd of suggested clipItself by tightening this nut down you're putting more pressure on the spring. So that the governorMoreItself by tightening this nut down you're putting more pressure on the spring. So that the governor has to work harder to pull back on the throttle. Cable.
Is throttle cable and accelerator cable the same?
An accelerator cable, sometimes called throttle cable, is a metal braided cable that serves as a mechanical link between the gas pedal and the engine's throttle plate. When the gas pedal is pressed, the cable is pulled and opens the throttle.
How do you know if your accelerator cable is bad?
Signs of a bad accelerator cableThe pedal feels stiff or hard to depress.The pedal sticks and does not release normally.There is slack in the pedal's movement.There is a rough or abnormally low idle.The engine stalls.There is a delay in response when you push the pedal down.More items...•
When should I replace my accelerator cable?
If your inspection reveals any damage, you'll need to replace your throttle cables. You might also need to replace them to accommodate a different handlebar.
How do you speed up a Yamaha electric golf cart?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
How can I speed up my gas golf cart?
How to Make Your Gas-Powdered Golf Cart Faster [Updated, 2022]1 Use A Better Golf Cart Battery.2 Increase Torque.3 Upgrade the Golf Cart Motor.4 Install a Torque Converter.5 Install a Higher-Performance Clutch.6 Tweak The Governor.7 Install A Cold Air Intake.8 Get Bigger Golf Cart Tires.More items...
Why does my Yamaha golf cart backfire?
Engine backfiring occurs when there is an air leak within your golf cart or sometimes when there is too much fuel inside. This can cause the piston to slam against the cylinder head and cause a tapping sound. An essential component of any golf cart is the drive belt.
How much does it cost to replace an accelerator cable?
How much does a throttle cable replacement cost? A throttle cable replacement usually costs around $50 to $100. It is usually sold individually but some are sold as part of a kit. Again, remember to check for compatibility before buying a throttle cable replacement.
Where is accelerator cable located?
Step 1: Locate the throttle cable. One end of the throttle cable is located in the engine compartment, attached to the throttle body. The other end is on the driver's side floor, attached to the accelerator pedal.
Can you adjust the accelerator cable?
0:482:18HOW TO ADJUST YOUR THROTTLE CABLE - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith all that said there's also a second location with you where you can adjust the throttle cableMoreWith all that said there's also a second location with you where you can adjust the throttle cable and that is at the pedal. You see there's a small sort of N stock bolt that the throttle pedal rests.
Why is my golf cart not accelerating?
When your electric golf cart does not accelerate, the first thing you need to keep in mind is that it is not a regular vehicle like your car . That's why the methods and solutions you use to get your car to start are not the same as the solutions you can apply to your cart.
What happens if your golf cart doesn't accelerate?
Bad Solenoid. If your golf cart does not accelerate, there is a possibility of the damaged solenoid. The solenoid is basically an electrical switch that enables the battery's flow from the battery into the motor. Check out the signs of the bad solenoid.
Why is my golf cart speed controller not working?
There are many reasons behind a speed controller malfunction. The most common problem that happens in the controller has aged due to infrequent use. These are just some of the issues that could be affecting your vehicle's acceleration. If you have trouble finding the issue of your golf cart accelerator, don't be afraid to take it to the mechanic.
How does a golf cart solenoid work?
The golf cart speed controller and solenoid are both controlled by the accelerator. The pedal is connected to the potentiometer. That means when you are pressing the pedal for acceleration, you are actually going through the potentiometer by pushing a rod. The potentiometer works as a communicator and tells the speed controller how much voltage it ...
How do you know it's an Accelerator Problem?
If your cart does not start smoothly , hesitates before starting, or does not gain speed properly , these are all signs of a bad or damaged accelerator.
How to adjust throttle cable on carburetor?
Adjust the throttle cable from the governor to the carburetor by turning the governor lever in the counterclockwise fully. Ensure that the carburetor throttle valve is open fully. If not, turn the adjustment nuts either inwards or outwards to adjust the throttle cable.
What cable is used to adjust a carburetor?
Often, it’s the throttle cable from the carburetor to the governor that needs adjustment.
What Does the Throttle Cable Do on a Golf Cart?
The throttle cable plays a key role in ensuring smooth power delivery and acceleration of the cart. It ensures that your golf cart operation is smooth and safe.
How to get a golf cart to idle?
Pull the spring that is present around the plastic piece located behind the shifter. Spin it until it falls back. Loosen the throttle cable present in the cable box to adjust the extent to which you can take it out of the housing. Press the accelerator so that the golf cart starts up and begins to idle.
How to prevent backfiring on a carburetor?
The slack in the second cable causes the ignition to fire off, the engine to turn over or the accelerator stop switch to open before the throttle shaft in the carburetor opens up. This will in turn prevent backfiring.
How to adjust carburetor slack?
Adjust the rear cable from the governor arm to the gas pedal until the slack is almost nil. Also, adjust the front cable from the carburetor to the governor arm until the carburetor stops opening before the motor starts getting cranked by the gas pedal switch. The throttle opening at the carburetor is high when the gas pedal is pressed fully.
How to remove throttle cable from bracket?
Loosen the nut on the spring rod to which the throttle cable is fitted. This will help to remove the rod from the bracket used to secure it in place.
